FLOOR POLISHER MODELS: U17-10090580 U20-10090600 U17X-10090590 U20X-10090610 UDS20-10090630 SP13-10090220 SP15-10090230 SP17-10090240 SP20-10090310 SP17X-10090280 SP20X-10090320 SPDS20-10090350 SPT17-10090370 SPT20X-10090380 SP17IE-10090270 SP17IA-10090260 SP17XIE-10090300 SP17XIA-10090290 SPDS17IE-10090340 SPDS17IA-10090330 SP17HDIE-10090250 IPX4 Operating Instructions (ENG) 86309580-A 10/08/08
MACHINE DATA LOG/OVERVIEW Model: Date of Purchase: Serial Number: Sales Representative: Address: Phone Number: 2 86309580 FLOOR POLISHER 10/08/08
TABLE OF CONTENTS Machine Data Log.............................2 Table of Contents..............................3 HOW TO USE THIS MANUAL How to use this Manual.....................1-1 SAFETY Important Safety Instructions ............2-1 Hazard Intensity Level. .....................2-2 Grounding Instructions 120V. ...........2-3 Grounding Instructions 230V ............2-4 Safety Label Location .......................2-5 OPERATION Technical Specifications ...................3-1 Handle Installation ........
HOW TO USE THIS MANUAL This manual contains the following sections: - HOW TO USE THIS MANUAL SAFETY OPERATIONS MAINTENANCE PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authorized dealers. When placing an order for parts, the machine model and machine serial number are important. Refer to the MACHINE DATA box which is filled out during the installation of your machine.
SAFETY IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Use only indoors. Do not use outdoors or expose to rain. Use only as described in this manual. Use only manufacturer’s recommended components and attachments.
SAFETY The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words – WARNING and CAUTION and FOR SAFTEY. The level of hazard intensity is determined by the following definitions: WARNING – Hazards or unsafe practices which COULD result in severe personal injury or death. CAUTION – Hazards or unsafe practices which could result in minor personal injury or product or property damage.
SAFETY GROUNDING INSTUCTIONS-120V Grounding Pin THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: In the USA this machine operates on a one 15 amp nominal 120V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors.
SAFETY GROUNDING INSTRUCTIONS-230V THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors. EXTENSION CORDS: If an extension cord is used, the wire size must be at least one size larger than the power cord on the machine, and must be limited to 50 feet (15.5m) in length. GROUNDING INSTRUCTIONS: This appliance must be grounded.
SAFETY SAFETY LABEL LOCATION NOTE: These drawings indicate the location of safety labels on the Machine. If, at any time, the labels become illegible contact your authorized representative for prompt replacement. WARNING LABEL P/N 86219740 PRV NO.
TECHNICAL SPECIFICATIONS ITEM DIMENSION/CAPACITY/MODEL Heavy-duty die cast aluminum deck with heavyduty rubber bumper, tubular steel adjustable handle with die cast aluminum handle housing CONSTRUCTION MOTOR 1HP 115V induction 1.5HP 115V induction 1.75 HP 115V 175/300RPM 1HP 230V induction 1.5 HP 230V induction 1.
HANDLE INSTALLATION WHEN INSTALLING THE HANDLE ASSEMBLY, CHECK ORIENTATION OF THE CORD ASM AND CORD HOOK. 4 MOTOR PLUG RECEPTACLE 5 6 MOTOR PLUG DECK ASSEMBLY PIVOT HOLE 3 2 1 (SEE NOTE) The handle must be installed by qualified personnel. Read all instructions thoroughly. The machine is shipped with handle unassembled. The machine is shipped with handle unassembled. Follow these steps for installation: 1. Remove handle and deck assembly from carton. 2.
OPERATION CONTROLS 1. Safety Lock – Prevents unintended operation of the machine. 2. Switch Levers – Turns machine on/off. 3. Adjustment Handle – Allows the handle to be adjusted to a comfortable operating position. 1 NOTE: It is incorrect to make it lock opposite from the way it was assembled by applying more force to the nut. The pivot pin is off center in relationship to the axis of the handle. To adjust handle, tighten nut on handle while in the locked position.
OPERATION MACHINE OPERATION DAILY MAINTENANCE 1. Inspect power cord for wear. To prevent electrical shock replace cords with frayed or cracked insulation immediately. For indoor use only. 2. Place machine in the storage position. When using the pad, always keep the machine moving when in contact with the floor. 3. Check pad condition. Change if soiled or torn. PAD INSTALLATION 1. Lay machine back, exposing the under side. High starting torque. Hold machine firmly with both hands. 1.
NOTES: 3-5 86309580 FLOOR POLISHER 10/08/08
MAINTENANCE SCRUB BRUSHES FINISHED FLOORS NOTE: All original equipment brushes are equipped with “Perform Alert©”. This feature will tell the operator when it is time to replace the scrub brushes. “Perform Alert©” brushes have pre-trimmed bright yellow tufts to indicate the length of a worn out brush. When the tufts in the scrub brush wear to a length equal to the yellow tufts, the scrub brushes should be replaced. Nylon Polish is the softest brush.
MACHINE TROUBLESHOOTING PROBLEM Machine will not run CAUSE Circuit breaker tripped in building.
NOTES: 86309580 FLOOR POLISHER 10/08/08 4-3
BRUSH/PAD DRIVER 3 3 1 1A-1E 2A-2W 5-1 86309580 FLOOR POLISHER 10/08/08
BRUSH/PAD DRIVER REF PART NO. PRV NO. QTY DESCRIPTION 1A 1B 1C 1D 1E 2A 86284280 86284330 86000120 86284290 86284300 86283720 02216 02396 02218 02217 02219 02232 - 2B 86283730 02233 - 2C 86283740 02234 - PAD DRIVER, 13" POLISHER PAD DRIVER, 15" POLISHER PAD DRIVER, 17" POLISHER PAD DRIVER, 19” HS PAD DRIVER, 20" POLISHER BRUSH, 13" NYL.POL. W/CLT.PLT BRUSH, 13" NYL.SCRUB W/CLT.PLT BRUSH, 13" MILD GRIT W/CLT.PLT BRUSH, 13" AGG. GRIT W/CLT.PLT BRUSH, 13" POLYPRO W/CLT. PLT BRUSH, 15” NYL.POL.
ELECTRICAL-120V 8 9 7 11 6 14 A-C 5 10 2 1 3 13 12 4 5-3 86309580 FLOOR POLISHER 10/08/08
ELECTRICAL-120V REF PART NO. PRV NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 86002010 86198450 86234150 86216920 86268450 86136780 86007110 86224750 86137290 86137330 86215140 86224930 86224300 DESCRIPTION SERIAL NO. FROM NOTES 14942 20005 23167 23206 70689 70801 72123 73993 87057 87208 140674 730012 730021 1 1 1 1 1 2 2 1 2 1 1 1 1 BOOT, 3/8 CIRCUIT BREAKER CLAMP, 5/16 NYLON CORD SET, 14/3 ST X 50FT, YLW CORDSET, 14/3 X 52 IN, SJT, BLK SCR, M4.8 X 10 HHTF TYPE B SCR, M3.
ELECTRICAL-230V 8 9 7 11 6 14 A-C 5 10 2 1 3 A-B 13 12 4 5-5 86309580 FLOOR POLISHER 10/08/08
ELECTRICAL-230V REF PART NO. PRV NO. QTY 1 1 DESCRIPTION SERIAL NO. NOTES FROM 1 2 86002010 86198450 14942 20005 BOOT, 3/8 CIRCUIT BREAKER CLAMP, 5/16 NYLON 3A 86216950 23212 CORD SET, EURO 1.5MM X 75 BLK SP17HDIE, SP17IE, SPX17IE, SPDS17IE 3B 86216970 23217 CORD SET, SAA33 1.
DECK 9A-9F 1 4 12 10 13 6 11 2A-2D 7 5 3 14 5-7 8 86309580 FLOOR POLISHER 10/08/08/08
DECK REF PART NO. PRV NO. QTY DESCRIPTION 1 86214930 2A 86216350 2B 86216330 03111 14373 14371 1 1 - AXLE, MAIN POLISHER BUMPER, EXTRUSION 53.4 IN. BUMPER, EXTRUSION 37.3” 2C 86216340 14372 - BUMPER, EXTRUSION 43.8" 2D 86216350 14373 - BUMPER, EXTRUSION 53.4" 3 4 5 6 7 8 9A 9B 27871 51328 57220 57276 70262 70691 29211 29212 2 2 2 2 2 2 1 1 CAP, EXTRUSION LINK, HANDLE ADJUST NUT, M6 X 1 NYLOCK NUT, PUSH FLAT RD .51 ID SCR, M8-1.
HANDLE 5 17 6 27 3 16 12 13 7 1 2 9 22 14 19 14 10 21 24 20 8 25 15 20 20 8 4 11 18 23 23 18 11 5-9 86309580 FLOOR POLISHER 10/08/08 26
HANDLE REF PART NO. PRV NO.
MOTOR 3 2 9 1 A-D 8 A-B 7 7 6 6 DUAL SPEED ONLY 5 4 5-11 86309580 FLOOR POLISHER 10/08/08
MOTOR REF PART NO. PRV NO. QTY DESCRIPTION 1A 86312270 - 1 MOTOR, 1HP 115V INDUCTION 1B 86312280 - 1 MOTOR, 1.5HP 115V INDUCTION 1C 86312300 - 1 MOTOR, 1HP 230V INDUCTION 1D 86312310 - 1 MOTOR, 1.5 HP 230V INDUCTION 2 86217490 27884 1 COVER, MOTOR 3 4 5 6 7 86223690 86136710 86279090 86223700 86223030 70702 70698 87067 70723 62917 3 4 4 6 1 SCR, M5 X .8 X 15MM BLK SCR, 5/16-18 X 3/4 HHCS GR5 BLK WASHER, 5/16 LOCK INT STAR PLT SCR, M5 X .
WIRING-120V CORD SET WHT GRN BLK -CB1 120V AC 15A 1 -SWITCH -SWITCH WHT WHT BLK BLK GRN -MOTOR GRN REF PART NO. PRV NO. QTY 1 86311830 - 1 5-13 DESCRIPTION WIRE, 125MM, BLK/14, 76029X76029 86309580 FLOOR POLISHER 10/08/08 SERIAL NO.
WIRING –230V CORD SET WHT BLK GRN -CB1 120V AC 15A 1 EMC FILTER -SWITCH -SWITCH EMC FILTER2 WHT WHT BLK BLK GRN -MOTOR M GRN REF PART NO. PRV NO. QTY 1 86311830 - 1 DESCRIPTION SERIAL NO.
SUGGESTED SPARE PARTS SERIAL NO. FROM PART NO. PRV NO. 86225710 86224740 86224750 86007110 86215130 86222560 86223550 87202 73990 73993 72123 14344 66334 67430 WASHER, BEARING (HANDLE ADJ) SPRING, EXT .5 OD X 3.5L SPRING, COMP .48 OD X .91 L SWITCH.
86309580 FLOOR POLISHER
