Operating instructions (ENG) MODELS: SCX364 10052410 IPX4 Read these instructions before using the machine.
Machine Data Label Overview The Saber Cutter is a battery powered, self-propelled, hard floor scrubber intended for commercial use. The appliance applies a cleaning solution onto a hard floor, scrubs the floor with brushes or pads, and then vacuums the soiled water back into the recovery tank. Warranty Registration Thank you for purchasing a Windsor product. Warranty registration is quick and easy. Your registration will allow us to serve you better over the lifetime of the product.
Table of Contents Machine Data Label . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Axle - Recommended Greasing . . . . . . . . . . . . . . .33 Machine Troubleshooting . . . . . . . . . . . . . . . . . . . .34 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 How To Use This Manual . . . . . . . . . . . . . . . . . . . . . 4 Safety Important Safety Instructions . . . . . . . . . . . . . . . . . .
How To Use This Manual The SAFETY section contains important information regarding hazardous or unsafe practices of the machine. Levels of hazards are identified that could result in product damage, personal injury, or severe injury resulting in death. This manual contains the following sections: • • • • • How to Use This Manual Safety Operations Maintenance Parts List The OPERATIONS section is to familiarize the operator with the operation and function of the machine.
Safety Important Safety Instructions When using an battery powered appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Use only indoors. Do not use outdoors or expose to rain. Use only as described in this manual. Use only manufacturer's recommended components and attachments.
Safety The following symbols are used throughout this guide as indicated in their descriptions: Hazard Intensity Level There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death. CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage.
Safety Safety Label Location NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them. SAFETY DECAL 86252530 PREV NO. 81494 PINCH POINT WARNING 86243830 PRV NO. 500663 BATTERY CAUTION 86252520 PRV NO. 80885 SEE MANUAL CIRCUIT BREAKER DECAL 86243530 PRV NO.
Operations Technical Specifications ITEM Nominal power Rated Voltage Rated Amperage Batteries Scrub Brush Motors Vacuum Motor Propelling Motor Mass (GVW) Weight empty without batteries Solution Control Solution tank capacity Recovery tank capacity Scrub brush diameter for 36 in. (90 cm) scrub head Scrub brush pressure Scrub brush speed Tires Casters Foundation Pressure (at recommended tire psi) Maximum Speed Frame Construction Brakes (optional) Minimum aisle u-turn width with 36 in.
Operations ITEM MEASURE Height Length with 36 in. (90 cm) scrub head Width without squeegee and scrub head Width of squeegee for 36 in. (90 cm) scrub head Width of scrub path for 36 in. (90 cm) scrub head Battery Compartment Dimensions 45 in. (114 cm) 72 in. (183 cm) 24 in. (61 cm) 35 in. (89 cm) 36 in. (90 cm) 23.5" L (60 cm) x 15" W (38 cm) x 14" H (36 cm) LENGTH WIDTH HEIGHT SPECIAL NOTES: The sound pressure level at the operator's ear was measured to be 68 dBA.
Operations How The Machine Works The Saber Cutter is a battery powered, self-propelled, hard floor scrubber intended for commercial use. The appliance applies a cleaning solution onto a hard floor, scrubs the floor with brushes, and then vacuums the soiled water back into the recovery tank. The machine's primary systems are the solution system, scrub system, recovery system, and directional control system. The function of the solution system is to store cleaning solution and deliver it to the scrub system.
Operations Components 11 13 3 1 7 2 4 16 9 6 12 8 10 5 15 14 1. Control Panel 2. Front Cover 3. Recovery Tank 4. Recovery Tank Drain Hose 5. Scrub Head Fixed 6. Solution Tank 7. Solution Tank Cover 8. Solution Tank Drain Hose 9. Solution Strainer 10. Rear Squeegee 11. Top Cover 12. Vacuum Motor 13. Recovery Tank Dome 14. Scrub Head Swinging 15. Front Side Squeegee 16.
Operations Controls 2 13 17 3 5 6 9 8 7 16 1 15 4 10 14 12 11 12 86037150 SCX364
Operations 4. PROPEL CONTROL LEVERS Controls the machine direction, and scrub brushes and solution flow. 1. Key Switch 2. Emergency Shut Off Switch (Optional) To propel machine forward, squeeze either propel lever. 3. Speed Control Knob 4. Propel Control Lever 5. Reverse Button The scrub brushes will not rotate and the solution will not flow to scrub deck with the propel levers in neutral. 6. Brush Switch 5. REVERSE BUTTON 7. Actuator Switch Deck Up-Down Controls the reverse function. 8.
Operations 7. ACTUATOR SWITCH DECK UP-DOWN 11. SQUEEGEE PITCH ADJUSTMENT KNOB Adjusts the amount of brush pressure to the floor by raising or lowering the scrub deck. Use the brush pressure indicator to determine the correct pressure. Adjusts the deflection at the ends of the squeegee. To increase brush pressure, press the bottom of the switch. To decrease brush pressure or rise the scrub deck, press the top of the switch. To increase squeegee blade deflection at the ends, turn knob counterclockwise.
Operations 13. BATTERY CHARGE LEVEL INDICATOR 16. BRUSH PRESSURE INDICATOR Indicates the charge level of the batteries. The brush pressure indicator corresponds to the amp draw of the scrub brush motors to tell how hard the motors are working. The green zone indicates medium or proper operating brush pressure. The red zone indicates heavy or excessive brush pressure. Operating in the red zone may cause the brush circuit breakers to trip. The meter display is divided into 10 vertical bars.
Operations Machine Operation Filling Solution Tank Pre-Run Machine Inspection Do a pre-run inspection to find possible problems that could cause poor performance or lost time from breakdown. Follow the same procedure each time to avoid missing steps. NOTE: See maintenance section for pre-run machine inspection checklist items. FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key. 1. Turn the machine power off. 2.
Operations Normal Scrubbing To Begin Scrubbing Plan the scrubbing pattern in advance. The longest track is around the perimeter of the area to be cleaned. For efficient operation, the runs should be the longest possible without turning, stopping, or raising and lowering scrub deck/squeegee. When operating the machine around people, pay close attention for unexpected movement. Use extra caution around children.
Operations Double Scrub Solution Tank For floors which are heavily soiled or have thick accumulations of floor finish may not clean sufficiently with one pass. In these cases it will be necessary to double scrub. 1. Loosen small drain hose from the retainer, then lower hose in direction of the drain. 1. To double scrub, make the first pass over the surface being cleaned with both squeegees up, vacuum off, the solution on and brushes down.
Maintenance Service Schedule MAINTENANCE Check batteries after charging; add water if necessary Check pad wear to prevent buildup of chemicals Check linkages and connectors for wear and damage Check hoses for wear, blockages, or damage Clean squeegee; check for adjustment; inspect for wear Check handles, switches, knobs, domes, and gaskets for damage Clean out recovery tank Clean out solution tank; remove and clean screen Clean outside of all tanks; check for damage Run vac motor for at least one minute to
Maintenance 4 1 11 8 5 6 7 10 2 12 13 3 1. Batteries 2. Rear Squeegee 3. Scrub Brushes 4. Float Shut-Off 5. Solution Strainer 6. Brush Motor 7. Traction Motor 8. Circuit Breakers 9. Scrubhead Fixed and Swinging 10. Vacuum Motor 11. Actuator Scrub Deck Up-Down 12. Actuator Scrub Deck In-Out 13.
Maintenance Batteries The batteries provide the power to operate the machine. The batteries require regular maintenance to keep them operating at peak efficiency. When servicing machine, avoid contact with battery acid. The machine batteries will hold their charge for long periods of time, but they can only be charged a certain number of times. To get the greatest life from the batteries, charge them when their charge level reaches 25% of a full charge. Use a hydrometer to check the charge level.
Maintenance Checking Battery Specific Gravity To Charge the Batteries Use a hydrometer to check the battery specific gravity. When servicing machine, avoid contact with battery acid. Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging. Wear eye protection and protective clothing when working with batteries. Charge batteries in a well ventilated area. Leave the battery cover open.
Maintenance 5. Replace the battery caps, and leave them in place while charging. 6. Unplug the battery connector from the machine. FOR SAFETY: When charging, connect the charger to the batteries before connecting the charger to the AC wall outlet. Never connect the charger to the AC wall outlet first. Hazardous sparks may result. 7. Plug the charger connector into the battery connector. Connect the charger AC plug to a wall outlet. The charger gauge should indicate that the batteries are charging. 8.
Maintenance Rear Squeegee To Remove Squeegee Assembly The front squeegee blade allows solution to pass through channels in the blade into the squeegee assembly while maintaining vacuum to provide lift. The front blade has four wear surfaces and can be rotated for extended life. The front blade should not require regular replacement under normal use. 1. With the squeegee in the up position, turn key switch "OFF". The rear blade wipes the floor to a near dry condition.
Maintenance To Adjust Squeegee Pitch 1. Choose a smooth, level surface. Turn "ON" the key switch. Lower the squeegee and drive forward at least 2 feet (60cm.). 2. With the squeegee down, stop the machine. Do not allow machine to roll back. FOR SAFETY: Before leaving or servicing the machine; stop on level surface, turn off machine and remove key. 3. Determine the differences, if any, in deflection of the squeegee blade between each end and the middle.
Maintenance Scrub Brushes Replacing or Installing Scrub Brushes There are four different types of brushes available to cover applications from cleaning heavily soiled floors to polishing. A pad driver is also available to take advantage of the many cleaning pads on the market. Please refer to the following to assist in selecting the proper brush or pad for the work at hand. 1. With the scrub deck up, turn "OFF" the machine. Uncoated Floors 3. Locate release lever on top of brush or pad driver.
Maintenance Solution Strainer Brush Motor Carbon Brush Replacement The solution strainer is located in front of the left front wheel. The solution strainer protects the solenoid valve from debris. If there is little or no solution flow to the ground, check the strainer for debris. Drain the solution tank and clean the solution strainer. To remove the strainer, turn the bottom part of the strainer counterclockwise until the bottom is separated. Clean out the debris from the wire mesh and re-assemble.
Maintenance Traction Motor Circuit Breakers Do not use a pressure washer to clean around the motors. Use tap pressure only. Circuit breakers interrupt the flow of power in the event of an electrical overload. When a circuit breaker is tripped, reset it by pressing the exposed button. If a circuit breaker continues to trip, the cause of the elec- Traction Motor Carbon Brush Replacement 20 Amp. Protects the left scrub brush motor.
Maintenance Vacuum Motor (Refer to the Vacuum Group in the parts section of manual) Vacuum Motor Carbon Brushes Replacement (Ametek) End Cap Carbon Brushes Do not use a pressure washer to clean around the vacuum motors. Use tap pressure only. Care must be taken so that water is not directed into vacuum motor air intakes. Changing Vacuum Motor If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center. 1.
Maintenance Actuator Scrub Deck Up-Down Removal/ Replacement FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and set parking brake (If option is installed). Actuator Scrub Deck In-Out Removal/ Replacement FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and set parking brake (If option is installed). 1. Remove front cover. 1. Remove front cover. 2.
Maintenance Front Side Squeegee The front blade allows solution to pass through channels in the blade into the squeegee assembly while maintaining vacuum to provide lift. The front blade has two wear surfaces and can be rotated for extended life. The front blade should not require regular replacement under normal use. The rear blade wipes the floor to a near dry condition. It is important the rear blade be in good condition to properly do its job.
Maintenance To Adjust Front Side Squeegee Deflection 1. Choose a smooth, level surface. Lower the front squeegee and deck and drive forward at least 2 feet (60cm) until the desired brush pressure is obtained. 2. With the squeegee down, stop the machine. Do not allow machine to roll back. FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key. 3. Observe the amount of squeegee deflection. It should deflect 1/4 in. (6.
Maintenance Axle - Recommended Greasing 1-2 strokes of Mobiltemp®78 or compatible claybased or calcium-based grease.
Maintenance Machine Troubleshooting PROBLEM Poor or no water pick-up on either squeegee CAUSE Squeegee out of adjustment Adjust squeegee Debris caught on squeegee Worn squeegee blades Vacuum hose clogged Vacuum hose disconnected from squeegee or recovery tank Vacuum hose damaged Remove debris Rotate or replace squeegee blades Clear obstruction from hose Recovery tank not sealed Foam filling recovery tank Vacuum motor does not run, or runs slowly Poor scrubbing performance Brush motors do not run, or
Maintenance PROBLEM Little or no solution flow to the floor No power to machine Little or no propel CAUSE Solution tank empty Solution flow turned off or set too low Solution strainer plugged Solution hoses obstructed Solution solenoid valve obstructed or stuck Vent hole in solution tank lid obstructed Battery disconnected Emergency shut-off activated (If included) Battery connections corroded Faulty main contactor Faulty key switch Low battery charge Wheels spin Controller overheated Uneven scrubbing
Notes: 36 86037150 SCX364
Parts PARTS 86037150 SCX364 37
Control Handle 1 10 6 3 5 2 4 7 8 9 11 38 86037150 SCX364
Control Handle REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 86238730 86257230 86254920 86231480 86277070 86240990 86277060 86277050 86238740 86004120 86004130 1 2 2 2 2 2 4 4 1 - DESCRIPTION HANDLE, LEFT SWITCH SPST MOM NO W/LEVER SPRING, COMP .24ODX1.25X.018 BUTTON, PROPEL SCREW, 4-40 X .625 PHPNHMS STL ZNPLT HOUSING, BUTTON SCREW, 8-32 X .875 PHPNHTC SCREW, 5/16-18 X .75 SCHCS SS HANDLE, RIGHT PROPEL HANDLE ASM LEFT PROPEL HANDLE ASM RIGHT 86037150 SCX364 SERIAL NO.
Cover (Front) & Tank Mount 4 5 2 6 1 3 40 86037150 SCX364
Cover (Front) & Tank Mount REF 1 2 3 4 5 6 PART NO. QTY 86069500 86010670 86276780 86062620 86004790 86276380 1 5 5 1 2 4 DESCRIPTION SERIAL NO. FROM NOTES BRKT, REC TO SOL BACK WASHER 5/16 FLAT SS SCREW, 5/16-18 X .75 HHCS SS COVER, FRONT SQZ PLAY 24V KNOB, 5/16-18 4 PRONG SCREW, 5/16-18 X 1.
Cover (Top) & Tank Mount 1 3 5 7 9 2 3 4 11 8 3 10 5 3 6 42 86037150 SCX364
Cover (Top) & Tank Mount REF PART NO. PRV NO. QTY 1 2 3 4 5 6 7 8 9 10 11 86062540 86271840 86010670 86239630 86276780 86073700 86069630 86233390 86271870 86276490 86292630 86276780 27926 57285 87029 41429 70728 140484 140485 80887 57290 70670 58004 70728 1 3 10 1 4 1 1 1 1 3 1 3 DESCRIPTION COVER, TOP, 24V, GRY NUT 5/16-18 HEX NYLOCK THIN SS WASHER 5/16 FLAT SS HINGE, COVER TO TANK SCREW, 5/16-18 X .
Decal 1 7 2 3 4 5 6 44 86037150 SCX364
Decal REF 1 2 3 4 5 6 7 PART NO. QTY 86243560 86243880 86243530 86243600 86243550 86243180 86004970 1 1 1 1 1 1 1 DESCRIPTION SERIAL NO. FROM NOTES LABEL, CUTTER RIGHT LABEL, ELEC. PANEL, SQZ.
Electrical Panel 1 45 2 3 47 33 48 7 DETAIL 'A' 30 13 42 49 24 32 35 34 27 4 40 41 31 5 37 29 38 39 36 12 26 10 6 11 25 8 28 9 18 44 24 43 DETAIL 'A' 23 22 19 32 14 15 20 16 9 17 21 46 86037150 SCX364
Electrical Panel REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 45 46 47 48 49 PART NO.
Lift Handle 6 1 7 9 5 2 1 48 86037150 SCX364 8 4 3
Lift Handle REF PART NO. QTY 1 2 3 4 5 6 7 8 9 86010670 86271840 86066860 86238360 86259400 86082390 86276780 86228840 86006930 5 1 1 1 1 1 4 1 1 DESCRIPTION SERIAL NO. FROM NOTES WASHER 5/16 FLAT SS NUT 5/16-18 HEX NYLOCK THIN SS BAR, SQG LIFT SWING 36V GRIP, 3/16 X 1.0 ORANGE WASHER, THRUST .51ID X 1OD BRO PLATE, LEVER NOTCH DELUXE SCREW, 5/16-18 X .75 HHCS SS BUSHING, .314 X .502 X .
Lift Handle Linkage 3 2 4 1 5 7 16 6 8 9 6 11 15 12 10 14 50 86037150 SCX364 13
Lift Handle Linkage REF PART NO. PRV NO. QTY DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 86276920 86238430 86276780 86010670 86082270 86010630 86273820 86069610 86271870 86009560 86005630 86077480 86003240 86008650 86228900 86259400 86278910 70755 36191 70728 87029 62946 87013 70019 140482 57290 82053 57022 51365 27942 80604 09138 87205 87003 2 1 4 4 1 2 1 1 1 1 2 1 1 1 1 1 2 SCREW, 3/8-16 X 1 HHCS SS NP GROMMET 1.00 ID 3/16 GRIP SCREW, 5/16-18 X .
Recovery Tank 1 2 3 4 12 5 25 11 7 24 20 23 22 6 21 19 8 11 10 7 9 11 28 27 11 18 12 11 27 17 16 28 15 26 13 14 52 86037150 SCX364
Recovery Tank REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 86274220 86003340 86003990 86246080 86014810 86032540 86276290 86001190 86089630 86237650 86372080 86002400 86004180 86002840 86008400 86006240 86004450 86004260 86271870 86075540 86069780 86010630 86273810 86236410 86257860 86257350 86089640 86233140 1 1 1 1 1 1 5 1 1 5 5 2 1 1 1 1 1 1 2 1 1 2 2 1 1 1 2 2 DESCRIPTION SERIAL NO. FROM NOTES SCREW, 6-32 X .
Scrub Brush/Pad Driver 7 6 5 9 4 8 7 6 5 9 4 8 1 5 3 54 86037150 SCX364 2A 2B 2C
Scrub Brush/Pad Driver REF PART NO. QTY 1 2A 2B 2C 3 4 5 6 7 8 9 86000170 86000180 86000190 86000200 86005070 86276590 86276580 86276600 86007910 86007280 86005940 2 2 2 2 1 3 4 3 1 1 1 DESCRIPTION SERIAL NO. FROM NOTES PAD DRIVER, 12" SD BRUSH 12" POLYPROPYLENE SD BRUSH 12" NYLON SD BRUSH 12" MILD GRIT SD LOCK PAD CENTER SNAP,TWO STEP SCREW, 12-11 X 1 PHPNHSMS SS TYPEA SCREW, 8-32 X .75 PHTRHMS SS SCREW, 10-12 X .75 PHTRHSMS SS TYPEA SPRING EXT .31D X 2.0L X .
Scrub Deck Motors 1 2 3 4 5 6 7 8 9 10 A 11 A TORQUE TO 84.
Scrub Deck Motors REF 1 2 3 4 5 6 7 8 9 10 11 PART NO. QTY 86361810 86216170 86092450 86010790 86276970 86279640 86279530 86004810 86003420 86279630 86279130 86007020 2 1 8 8 2 4 2 2 2 2 2 DESCRIPTION MOTOR ASM, 36VDC 300RPM GEAR BRUSH SET MOTOR 53644 FRAME, SQZ PLAY ASM, L WASHER, 3/8 X .680 X .094 SPL STL ZNPLT SCREW, 3/8-16 X .75 HHCS SS WASHER, .780 X 1.63 X .25 FLT YW ZNPLT WASHER, 3/4 X 1.312 X .09 FLT PSVT KEY, 1/4 X 1/4 X 1 LCSTL DRIVER, BRUSH SD WASHER, 5/16 X 1.13 X .09 FLT WASHER, 5/16 X .
Scrubdeck Right Frame 25 1 2 3 7 2 26 4 5 8 6 12 11 10 24 26 9 23 13 16 17 14 15 18 19 20 21 A 22 58 A TORQUE TO 84.
Scrubdeck Right Frame REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 86361810 86065050 86065040 86233560 86234820 86001350 86277150 86253980 86007650 86011020 86087990 86274070 86271840 86010790 86276920 86279640 86279530 86004810 86003420 86279630 86279130 86007020 86092440 86271900 86279930 86010670 1 2 1 2 1 2 2 1 2 2 1 6 2 4 4 1 2 1 1 1 1 1 1 6 1 4 DESCRIPTION MOTOR ASM, 36VDC 300RPM GEAR SPACER, SIDE SQG SPACER, TOP SQG LINKAGE CLIP, TREE .
Scrubdeck Left Frame 1 2 3 21 19 20 4 3 1 19 17 16 5 18 15 13 14 6 7 3 8 9 10 12 11 60 86037150 SCX364
Scrubdeck Left Frame REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 86008670 86070290 86271840 86014670 86231280 86233560 86234820 86272530 86272520 86253970 86087980 86274070 86271900 86070390 86011020 86001350 86277150 86271950 86256500 86010670 86254930 2 1 6 1 3 4 2 1 1 1 1 8 8 1 1 1 1 1 2 3 1 DESCRIPTION SERIAL NO. FROM NOTES COTTER 3/8" RING BRKT, ACTUATOR MOUNT NUT 5/16-18 HEX NYLOCK THIN SS SP ACTUATOR, 24V 4.9 STROKE DBLS BUSHING, .377 X .627 X .63 CLIP, TREE .
Scrubdeck 1 2 3 4 5 6 7 8 62 86037150 SCX364
Scrubdeck REF PART NO. QTY 1 2 3 4 5 6 7 8 86070360 86228900 86070260 86259420 86006930 86228840 86271870 86271840 1 4 1 14 2 2 4 2 DESCRIPTION SERIAL NO. FROM NOTES BRKT, SQZ PLAY SLIDER BUSHING, .252 X .503 X .75 FLG BRKT, SIDE ACTUATOR WASHER, .510 X 1 X .093 THR SCREW, 5/16-18 X 1 SCHBTNHCS SS BUSHING, .314 X .502 X .
Scrubdeck Linkage 1 1 2 3 4 5 6 7 12 8 9 10 11 64 86037150 SCX364
Scrubdeck Linkage 1 REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 86076170 86070280 86076160 86271870 86076150 86259410 86070270 86076140 86010630 86273740 86271840 86228920 1 1 1 4 1 16 1 1 8 4 8 4 DESCRIPTION SERIAL NO. FROM NOTES GUIDE, SQZ PLAY DECK, RR BRKT, DECK LINKAGE RIGHT GUIDE, SQZ PLAY DECK, RL NUT, 1/4-20 HEXTHIN NYLOCK SS GUIDE, SQZ PLAY DECK LL WASHER, .510 X 1 X .063 THR BRKT, DECK LINKAGE LEFT GUIDE, SQZ PLAY DECK LR WASHER, 1/4 X .625 FLT SS SCREW, 1/4-20 X 1.
Scrubdeck Linkage 2 11 10 9 8 2 7 1 2 3 4 5 6 66 86037150 SCX364
Scrubdeck Linkage 2 REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 86226830 86007020 86010670 86276790 86278910 86278330 86224290 86006560 86238510 86271840 86075860 1 4 2 1 2 2 6 2 2 9 1 DESCRIPTION SERIAL NO. FROM NOTES SPRING EXT .68D X3.00L X.098W SCREW, 5/16-18 X 1.25 HHCS SS NP WASHER 5/16 FLAT SS SCREW, 5/16-18 X 1.75 HHCS SS WASHER, 3/8 X .875 X .05 FLT SS SHOULDER BOLT, 3/8 X .375L SS SPACER, .317ID X .5OD X .44LG SCREW, 5/16-18 X 1 HHCS SS NP GROMMET, 1.75ID X2.50OD X .
Scrubdeck Lift 1 2 17 3 4 16 15 5 6 4 7 8 14 9 7 10 11 12 13 68 86037150 SCX364
Scrubdeck Lift REF PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 86276920 86276430 86279590 86005630 86070230 86070240 86008670 86276670 86068140 86255280 86005840 86005730 86233410 86248970 86011960 86272410 86069930 PRV NO. QTY 2 4 2 6 1 1 2 2 1 4 2 2 1 1 1 1 1 DESCRIPTION SCREW, 3/8-16 X 1 HHCS SS NP SCREW, 3/8-16 X 1.
Solution 1 1 2 3 4 5 6 HOSE FROM FILTER ASM.
Solution 1 REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 86273950 86234790 86246080 86014810 86008270 86240460 86282050 86233110 86271840 86276380 86233150 86197910 86010670 86276780 1 1 1 1 1 1 1 1 3 3 1 1 4 1 DESCRIPTION SERIAL NO. FROM NOTES SCR, 6-32 X 1/2 PPHMS SS COVER, CLP SOLUTION LANYARD, 18.0 W/LOOP & EYE NUT, 6-32 ACORN SS TANK SOLUTION, 24V, BLU HOSEBARB 1/2MPT X 1.0 HOSE HOSE 1ID X .12W CLR X 24.5" CLAMP, 1.0" WORM GEAR NUT 5/16-18 HEX NYLOCK THIN SS SCREW, 5/16-18 X 1.
Solution 2 TO SOLUTION TANK 1 2 3 4 8 9 5 7 6 7 72 86037150 SCX364
Solution 2 REF 1 2 3 4 5 6 7 8 9 PART NO. QTY 86282190 86233150 86007560 86005870 86007750 86313160 86273750 86281100 86010540 86003460 86136820 86271870 86070380 86264940 1 3 1 1 1 2 1 1 4 1 2 DESCRIPTION HOSE, 1/2ID WIRE BOUND X 13" CLAMP, 3/8 HOSE (D-SLOT) STRAINER 1/2 HOSE 20 MESH O-RING SEAL FILTER SEAL RON-VIK SCREEN, 20 MESH STRAINER SCRBR CAP, STRAINER SHORT SCREW, 1/4-20 X .625 HHCS SS NP HOSE 1/2ID WIRE BOUND X 7" VALVE 24VDC SOL.
Solution Hose Asm 1 10 9 8 7 6 2 5 4 3 74 86037150 SCX364
Solution Hose Asm REF PART NO. 1 2 3 4 5 6 7 8 9 10 86282220 86200280 86271830 86282230 86282240 86001530 86264940 86033220 86198010 86282210 PRV NO. QTY 1 3 3 1 1 1 3 1 3 1 DESCRIPTION SERIAL NO. FROM NOTES HOSE, 1/4ID NYLOBRD X 19" HOSEBARB, 3/8 MPT X 1/4 90D NUT, 3/8-16 LK NYL BLK HOSE, 1/4ID NYLOBRD X 29" HOSE, 1/2ID WIRE BOUND X 6" HOSEBARB, 1/2MPT X 1/2 HOSE 90 CABLE TIE 11.
Squeegee - Front Side 11 1 2 10 3 4 5 6 7 8 9 76 86037150 SCX364
Squeegee - Front Side REF PART NO. 1 2 3 4 5 6 7 8 9 10 11 86010670 86011020 86001350 86088000 86004790 86007590 86094210 86007600 86088010 86271900 86279750 PRV NO. QTY 1 1 1 1 2 1 1 1 1 6 1 DESCRIPTION SERIAL NO. FROM NOTES WASHER 5/16 FLAT SS WHEEL 3" DIA CUSHION RUBBER BUSHING, SPANNER .435 X 1.
Squeegee-Rear 38 2 37 36 3 4 34 35 5 14 16 13 34 5 33 6 32 8 17 9 7 15 10 31 1 30 22 29 12 18 7 2 19 28 20 21 26 24 27 25 78 23 86037150 SCX364 11
Squeegee-Rear REF PART NO.
Squeegee Lift Linkage (Lower) 1 2 20 3 4 5 6 19 7 1 18 8 17 16 9 15 10 11 12 14 13 80 86037150 SCX364
Squeegee Lift Linkage (Lower) REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 86008670 86069450 86271840 86228840 86259420 86009200 86279510 86082150 86009560 86007270 86005630 86072530 86276870 86277130 86249060 86008870 86010630 86008650 86259400 86008860 2 1 2 2 2 1 1 1 1 1 1 1 1 2 1 2 1 1 2 1 DESCRIPTION SERIAL NO. FROM NOTES COTTER, 3/8" RING BRKT, SQG PIVOT LIFT NUT 5/16-18 HEX NYLOCK THIN SS BUSHING, .314 X .502 X .5 FLG WASHER, .510 X 1 X .
Front Squeegee Linkage 16 17 13 11 15 3 12 14 1 10 2 3 9 8 4 5 3 6 7 82 86037150 SCX364
Front Squeegee Linkage REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 86070250 86276780 86010670 86077500 86082970 86271840 86004790 86271870 86089700 86078480 86278190 86254950 86066880 86278370 86078470 86224290 86089690 1 2 11 1 2 2 2 2 1 1 1 1 1 1 1 1 1 DESCRIPTION SERIAL NO. FROM NOTES BRKT, SIDE SQG PIVOT SCREW, 5/16-18 X .75 HHCS SS WASHER 5/16 FLAT SS LINKAGE, SIDE SQG PLATE, SIDE SQG. ADJ.
Vacuum 14 13 12 11 10 1 3 15 1 3 2 8 2 1 3 1 7 6 4 5 84 86037150 SCX364 2
Vacuum REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PART NO. QTY 86278910 86005630 86276920 86004250 86001620 86002400 86271870 86070370 86120190 86233430 86091170 86005460 86230810 86326980 86010630 86273810 86064910 7 5 5 1 1 2 3 1 1 1 1 1 3 3 1 DESCRIPTION WASHER, 3/8 X .875 X .05 FLT SS NUT, 3/8-16 HEXTHIN NYLOCK SS SCREW, 3/8-16 X 1 HHCS SS NP HOSE 1.0 BLK VAC X 8 FT HOSE ASSEMBLY 1.5 BLK VAC X 67 CLAMP, 2.0" WORM GEAR X .
Wheels And Frame 1 2 5 9ABCDE 11 3 12 4 6 10 7 8 86 86037150 SCX364
Wheels And Frame REF 1 2 3 4 5 6 7 8 9A 9B 9C 9D 9E 10 11 12 PART NO. QTY 86006560 86075870 86002310 86270880 86238430 86000800 86216150 OBSOLET E 86241840 86230330 86271840 86011050 86137420 86011040 86354660 86354670 86271860 86081870 86278910 DESCRIPTION SERIAL NO. FROM NOTES 4 1 2 8 1 1 - SCREW, 5/16-18 X 1 HHCS SS NP FRAME, MAIN SQZ PLAY CASTER, 4DIA X 2 W X 3.56 R NUT, 3/8-16 SERFLG STL ZNPLT GROMMET 1.
Wiring-Battery 1 13 2 8 11 3 5 1 12 4 9 10 6 7 88 86037150 SCX364
Wiring-Battery REF PART NO. QTY DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 86010120 86271870 86271910 86008920 86009000 86010850 86010860 86260520 86233360 86270890 86010650 86273980 2 2 8 8 3 1 1 2 1 1 1 1 CONNECTOR 175 DCA RED W/O TERMS NUT, 1/4-20 HEXTHIN NYLOCK SS NUT, 5/16-18 FLEX LK STL GRA CDPLT BOOT, RUBBER TERM. ISOLATOR WIRE, 4X9.
Wiring-Control Panel DIAGRAM C DIAGRAM B DIAGRAM A 51 RED 30 RED 73 RED 49 BLK 56 RED 18 BLU 66 BLU 48 BLK 71 BLU 47 RED 52 RED 41 BLU 29 YLW 43 BLK 50 BLK 72 BLK 63 BLK 62 RED 63 BLK 26 RED 61 BLK 28 WHT 27 GRN 61 BLK 26 RED BATTERY METER REV SWITCH FORWARD SWITCH 1 E-STOP 69 RED 26 RED 6 BLK 67/68 BLK 4 POT 7 RED 11 RED 58 RED 69/70 RED 58 RED 30 RED 14/15 RED 65 RED 66 BLU 3 20 BLU 12 RED 13 RED 62 RED FORWARD SWITCH 2 32 RED 71 BLU 68 BLK 2/25 BLK 33 RED 59 BLK
Wiring-Control Panel REF PART NO. QTY 1 2 3 4 5 6 7 86239040 86238990 86261210 86003410 86267340 86269300 86267360 1 1 2 1 2 1 1 DESCRIPTION SERIAL NO.
Wiring-Main Harness ACTUATOR DECK IN-OUT 80 RED 82 BRN 83 BLK 76 RED LEFT BRUSH MOTOR 74 RED RIGHT BRUSH MOTOR 75 BLK 77 BLK 72 RED VAC MOTOR 81 BLK SWING BRUSH MOTOR 73 BLK 5 BRN ACTUATOR DECK UP-DOWN 6 BLK 69 RED DIAGRAM A 68 GRN/YLW SOLENOID VALVE 75 BLK 78 RED 79 BLK 76 RED 77 BLK 1,2 74 RED DIAGRAM B 5 BRN 82 BRN PROPEL MOTOR 68 GRN/YLW 69 RED 83 BLK 6 BLK 78 RED 79 BLK A B C DIAGRAM C 80 RED 81 BLK 92 86037150 SCX364
Wiring-Main Harness REF 1 2 PART NO. QTY 86239030 86238980 1 1 DESCRIPTION SERIAL NO.
WHT BLK SWITCH DECK SWITCH DECK 86261210 86261210 86003410 WHT BLK Wiring-Schematic INDICATES OPTIONAL ACCESSORY 94 86037150 SCX364
Options OPTIONS 86037150 SCX364 95
Brake 10 8 14 9 11 12 15 11 14 13 17 2 1 6 9 4 4 10 3 2 1 5 11 7 9 2 12 96 86037150 SCX364 8 16
Brake REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 86248370 86006220 86252070 86231330 86255060 86070070 86234850 86272610 86231820 86008660 86010630 86271870 86070150 86259400 86228900 86273820 86077280 2 3 1 2 2 1 1 2 1 2 6 5 1 2 1 1 1 DESCRIPTION SERIAL NO. FROM NOTES PAD, BRAKE PIN, ROLL 1/4 X 1.25L ROD, BRAKE 24V BUSHING, .6270 X .753 X 1 FLG BRZ SPRING, EXT .43D X2.50L X.047W BRKT, LOWER BRAKE MOUNT 24V CRANK, BRAKE PIN, CLEVIS 5/16 X .
Emergency Stop 1 98 86037150 SCX364
Emergency Stop REF PART NO. QTY 1 2 86007180 86269300 1 1 DESCRIPTION SWITCH EMERGENCY STOP WIRE, 16" RED/18 STRIP X STRIP 86037150 SCX364 SERIAL NO.
Suggested Spare Parts PART NO.
Serial Numbers REF. NO.
