HIGH SPEED BURNISHER MODELS: LB2000I LB2000IA UB2000F LB2000 10090200 10090210 10090620 10090190 Operating Instructions (ENG) 86309600-B 01/29/09
MACHINE DATA LOG/OVERVIEW Model: Date of Purchase: Serial Number: Sales Representative: Address: Phone Number: OVERVIEW The High Speed Burnisher is a mains powered, portable floor burnisher intended for commercial use. The appliance can be fitted with a variety of pads to perform various floor care functions. The appliance employs active dust control, and automatically adjusted pad pressure.
TABLE OF CONTENTS Machine Data Log/Overview................................2 Table of Contents.................................................3 HOW TO USE THIS MANUAL How to use this Manual........................................1-1 SAFETY Important Safety Instructions ...............................2-1 Hazard Intensity Level..........................................2-2 Grounding Instructions. ........................................2-3 OPERATION Technical Specifications....................................
HOW TO USE THIS MANUAL This manual contains the following sections: - HOW TO USE THIS MANUAL SAFETY OPERATIONS MAINTENANCE PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authorized dealers. When placing an order for parts, the machine model and machine serial number are important. Refer to the MACHINE DATA box which is filled out during the installation of your machine.
SAFETY IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To r educe the risk of fire, electric shock, or injury: Use only indoors. Do not use outdoors or expose to rain. Use only as described in this manual. Use only manufacturer’s recommended components and attachments.
SAFETY The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WARNING - Hazards or unsafe practices, which COULD result in severe personal injury or death. CAUTION - Hazards or unsafe practices, which could result in minor personal injury or product or property damage.
SAFETY GROUNDING INSTUCTIONS-120V Grounding Pin THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: In the USA this machine operates on a one 15 amp nominal 120V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors.
SAFETY GROUNDING INSTRUCTIONS-230V THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors. EXTENSION CORDS: If an extension cord is used, the wire size must be at least one size larger than the power cord on the machine, and must be limited to 50 feet (15.5m) in length. GROUNDING INSTRUCTIONS: This appliance must be grounded.
SAFETY SAFETY LABEL LOCATION NOTE: These drawings indicate the location of safety labels on the Machine. If, at any time, the labels become illegible contact your authorized representative for prompt replacement. WARNING LABEL P/N 86219740 PRV NO.
TECHNICAL SPECIFICATIONS ITEM Construction Motor Transmission Pad speed Electrical system: LB2000I, LB2000IA LB2000, UB2000F Cable Switches Pad Holder Wheels Handle Dimensions (L x W x H) Pad size (See note) DIMENSION/CAPACITY Heavy-duty die cast aluminum deck with heavy-duty rubber bumper, tubular steel self adjusting handle with die cast aluminum handle housing. 1.5 hp Direct drive from motor shaft. 2000 rpm 230 volts, 50Hz 115 volts, 60Hz 75’ [22.9 m] Dual levers with safety lock. ∅20” [50.
OPERATION HANDLE ASSEMBLY 2 3 1 HANDLE MOUNT BRACKET DECK ASSEMBLY HANDLE INSTALLATION The machine is shipped with handle unassembled. Follow these steps for installation: 1. Remove handle and deck assembly from carton. 4. Slide Bolt (item 3) through, washers (item 2), Handle Mount Brackets and Handle Assembly as shown. Tighten bolt (item 3) and nut (item 1) until the handle cannot twist in the mount bracket (4550 foot pounds). 5. Check handle for movement up and down. 2.
OPERATION 6. To stop the machine, release the switch levers. CONTROLS 1. Safety Lock – Prevents unintended operation of the machine. 2. Switch Levers – Turns machine on/off. NOTE: The machine is equipped with a circuit breaker to protect the motor in the event an overload condition occurs. The circuit breaker is located on the handle. Push the reset button to restart the machine. If the breaker trips again, correct the cause of overloading before proceeding. 1 2 7. Do not let machine rest on pad.
MAINTENANCE MACHINE TROUBLESHOOTING PROBLEM CAUSE Tripped circuit breaker SOLUTION Reset Circuit breaker tripped in building. Fuse in motor is blown Check and reset Machine will not run Power switch failure Faulty power cord Equipment not grounded Pad not centered Follow grounding instructions exactly. Have an electrician inspect building’s wiring. Ensure that the machine wiring matches the appropriate wiring diagram. Replace any wires or components, which are shortcircuiting.
MAINTENANCE SERVICE SCHEDULE MAINTENANCE Check pad wear to prevent buildup of chemicals Check pad driver system for damage Check handles, switches, and knobs for damage Store with pad off the floor Check all bearings for noise Check skirt/bumpers for damage and replace as necessary Check overall performance of machine 4-2 86309600 (2000) BURNISHER 10/08/08 DAILY MONTHLY * * * * * * *
NOTES: 86309600 (2000) BURNISHER 10/08/08 4-3
DECK 1 2 3 5 6A-B 4 7 8 9 11 10 16 12 15 5-1 14 13 86309600 (2000) BURNISHER 10/08/08
DECK REF PART NO. PRV NO. QTY DESCRIPTION 1 2 3 4 5 86216280 86217520 86001390 86223430 86276810 140449 27918 140441 67463 70738 4 1 1 1 2 BUMPER, RUBBER COVER, FILTER BAG BAG, DUST (PACKAGE OF 10 BAGS) RETAINER, CORD SCR, M5 X .
ELECTRICAL 1 3 4 2 15 14 A-B 5 6 7 12 11 5-3 10 9 8 86309600 (2000) BURNISHER 10/08/08 13 A-C
ELECTRICAL REF PART NO. PRV NO. QTY DESCRIPTION 1 2 3 86136780 86137290 86224750 70801 87057 73993 2 2 1 4 86007110 72123 2 5 86288450 70689 1 6 86137330 87208 1 7 8 9 10 11 12 86198450 86227300 86224930 86215430 86216940 86002010 20005 730021 730012 14407 23209 14942 1 1 1 1 1 1 SCR, M 3.5 X 40 PHTF TYPE B WASHER, M4 SHAKEPROOF SPRING, COMP, .48OD X .91L SWITCH, 25A SPST 125-250V SNAP SCR, M4.
HANDLE-LOWER 16 17 14 19 17 15 18 10 24 7 8 23 6 9 1 2 5 11 3 4 13 12 22 21 20 25 8 5-5 86309600 (2000) BURNISHER 10/08/08
HANDLE-LOWER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PART NO. 86276810 86198450 86223490 86222570 86215480 86223500 86288760 86225720 86224310 86288770 86221720 86226020 86224590 86215390 PRV NO.
HANDLE-UPPER 13 4 6 12 5 1 3 7 2 10 8 10 8 11 5-7 86309600 (2000) BURNISHER 10/08/08 9
HANDLE-UPPER REF PART NO. 1 2 3 4 5 6 7 8 86136670 86136680 86224740 86225370 86004070 86005160 86136350 86279080 PRV NO. 70686 70687 73990 78437 36196 51327 57274 87058 9 86311810 - 1 10 11 86288450 86225390 70689 78473 3 1 12 86311820 - 1 13 86005150 51326 1 QTY DESCRIPTION 2 2 2 1 2 2 4 3 SCR, M6 X 45 SHCS BLK SCR, M6 X 50 SHCS BLK SPRING, EXT, .50D X 3.
MOTOR 3 2 1 A-B 6 4 5 5-9 86309600 (2000) BURNISHER 10/08/08
MOTOR REF PART NO. PRV NO. QTY 1A 86312260 - 1 1B 86312250 - 1 2 3 86217490 86223690 27884 70702 1 3 4 86010790 87163 4 5 86006920 70507 4 6 86219610 48082 1 DESCRIPTION SERIAL NO. FROM MOTOR, 115V 1.5HP 20000RPM MOTOR, 230V 1.5HP 20000RPM COVER, MOTOR 1.25HP SCR, M5 X .8 X15MM BLK WASHER, 3/8 SPLIT LOCK PLTD SCR, 3/8-16 X 3/4 HHCS GR5 PLT KEY, 3/16 SQ X .
PAD/DRIVER 8 1 9 2 4 7 6 5 5-11 86309600 (2000) BURNISHER 10/08/08 3
PAD/DRIVER 1 2 PART NO. 86010720 86006920 PRV NO. 87086 70507 3 86222470 64108 1 4 5 6 7 86279210 86274590 86276740 86246740 87102 70244 70720 51353 1 1 3 1 8 86223660 730065 1 9 86216230 730074 1 REF QTY DESCRIPTION 4 4 WASHER, M10 X 30 PLTD SCR, 3/8-16 X 3/4 HHCS PLT PAD DRIVER, 20 INCH BURNISHER WASHER, 5/16 ID X 1-1/4 OD SCR, 5/16-24 X 1/2 HHMS SS SCR, #10 X 3/8 PPHST TYPE B LOCK, PAD DRIVER BLUE SHROUD, ASM.
WIRING-120V CORD SET WHT GRN BLK -CB1 120V AC 15A 1 -SWITCH -SWITCH WHT WHT BLK BLK GRN -MOTOR GRN REF PART NO. PRV NO. QTY 1 86311830 - 1 5-13 DESCRIPTION WIRE, 125MM, BLK/14, 76029X76029 86309600 (2000) BURNISHER 10/08/08 SERIAL NO.
WIRING-230V CORD SET WHT BLK GRN -CB1 120V AC 15A 1 EMC FILTER -SWITCH -SWITCH EMC FILTER2 WHT WHT BLK BLK GRN -MOTOR M GRN REF PART NO. PRV NO. QTY 1 86311830 - 1 DESCRIPTION SERIAL NO.
SUGGESTED SPARE PARTS PART NO. PRV NO. DESCRIPTION 86224740 86224750 86007110 86312460 86291460 86223460 86003660 86003670 86001020 86246740 86001390 86215390 86216230 86001820 86001720 73990 73993 72123 67499 34378 34379 09135 51353 140441 140420 730074 14404 140785 SPRING, EXT .5OD X 3.5L SPRING, COMP .48OD X .
86309600 (2000) BURNISHER
