Operating Instructions (ENG) MODELS: CS26 10061500 CSC26 10061510 CSM26 10061580 CSCM26 10061590 CS26SP 10061520 CSC26SP 10061530 CSM26SP 10061600 CSCM26SP 10061610 Read these instructions before using the machine.
Machine Data Label / Overview Overview The Chariot Scrubber is a battery powered, stand-on, hard floor scrubber intended for commercial use. The appliance applies a cleaning solution onto a hard floor, scrubs the floor with brushes or pads, and then vacuums the soiled water back into the recovery tank. Warranty Registration Thank you for purchasing a Windsor product. Warranty registration is quick and easy. Your registration will allow us to serve you better over the lifetime of the product.
Table of Contents Machine Data Label / Overview . . . . . . . . . . . . . . . .2 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . .5 HAZARD INTENSITY LEVEL . . . . . . . . . . . . . . . . . . 7 Safety Label Locations . . . . . . . . . . . . . . . . . . . . . . . 9 To Repair or Replace Vacuum Motor . . . . . . . . . . . 47 Drive Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How To Use This Manual This manual contains the following sections: • • • • • How to Use This Manual Safety Operations Maintenance Parts List The SAFETY section contains important information regarding hazardous or unsafe practices of the machine. Levels of hazards are identified that could result in product damage, personal injury, or severe injury resulting in death. The OPERATIONS section is to familiarize the operator with the operation and function of the machine.
Safety IMPORTANT SAFETY INSTRUCTIONS When using this machine, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Use only indoors. Do not use outdoors or expose to rain. Use only as described in this manual. Use only manufacturer's recommended components and attachments.
Safety MESURES DE SÉCURITÉ IMPORTANTES Lors de l'utilisation d'un appareil à batteries, il est nécessaire de respecter systématiquement des mesures de sécurité de base, comme suit: PRENEZ NOTE DE TOUTES CES MESURES AVANT D'UTILISER CETTE MACHINE. Pour réduire les risques d'incendie, de chocs électriques, ou de blessures: N'utiliser cette machine qu'en intérieur. Ne jamais l'utiliser à l'extérieur ou dans la pluie. N'utiliser cette machine que comme décrit dans le présent manuel.
Safety The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death. CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage.
Safety Les symboles ci-dessous sont utilisés à travers ce manuel comme illustré dans leurs descriptions: DEGRÉS DE RISQUES EN CAS DE DANGER Il existe trois degrés de risques identifiés par les termes signalétiques -AVERTISSEMENT et ATTENTION et POUR VOTRE SÉCURITÉ. Le degré de risque est défini de la manière suivante: AVERTISSEMENT - Dangers ou méthodes dangereuses qui POURRAIENT provoquer de graves blessures ou entraîner la mort.
Safety Safety Label Locations These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them. EMPLACEMENT DE L'ÉTIQUETTE DE SÉCURITÉ REMARQUE : Ces dessins indiquent l'emplacement des étiquettes de sécurité sur la machine.
Operations Technical Specifications ITEM Nominal power Rated Voltage Rated Amperage Batteries Battery Compartment Dimensions Scrub Brush Motors - Disk Machine Scrub Brush Motors - Cylindrical Machine Vacuum Motor(s) Maximum flow rate of vacuum motor Maximum suction of vacuum motor Propelling Motor Mass (GVW) Weight empty without batteries Solution Control Solution capacity Recovery capacity Scrub brush diameter - Disk Machine Scrub brush diameter - Cylindrical Machine Scrub brush pressure Scrub brush pressu
Operations ITEM MEASURE 50.0 inches (1270 mm) 56.1 inches (1425 mm) 29.5 inches (749 mm) 32.7 inches (830 mm) 33.
Operations How This Machine Works The Chariot® is a battery powered, self-propelled, hard floor scrubber intended for commercial use. The appliance applies a cleaning solution onto a hard floor, scrubs the floor with brushes, and then vacuums the soiled water back into the recovery tank. The machine's primary systems are the solution system, scrub system, recovery system, and operator control system. The function of the solution system is to store cleaning solution and deliver it to the scrub system.
Operations 2 7 1 11 3 5 6 8 4 10 9 12 Components 7. Recovery Sight Dome 1. Control Panel-Drive 8. Solution Drain Hose 2. Control Panel-Scrub 9. Scrub Deck Aqua-Mizer™ 3. Console 10. Scrub Deck Skirt 4. Pedal Platform 11. Recovery Lid 5. Rear Cover 12. Recovery Drain Hose 6.
Operations 8 9 5 2 3 7 1 6 4 14 86367610 Chariot CS26
Operations Drive Controls 1. Key Switch 2. Emergency Stop/Brake Switch 3. Directional Control / Drive Reset Switch 4. Throttle Pedal 5. Horn Button 6. Steering Wheel 7. Speed Control 8. Battery Discharge Indicator 9. Hour Meter 1. KEY SWITCH Controls the power for machine functions. To turn the machine power on, rotate key clockwise. To turn the machine off, rotate key counterclockwise.
Operations 4. THROTTLE PEDAL Controls the speed of the vehicle within the speed control setting selected. Pressing the pedal causes the machine to travel in the direction selected by the Directional Control Switch. To increase speed, increase pressure on the pedal. To decrease speed, decrease pressure on the pedal. 5. HORN BUTTON The horn is activated by pressing the horn button. 6. STEERING WHEEL The steering wheel turns the front wheel causing the machine to change direction. 7.
Operations 8. BATTERY CHARGE LEVEL INDICATOR Indicates the charge level of the batteries. The meter display is divided into 10 bars. Bars illuminated on the far right indicate full charge. Bars flashing near the left side indicate the batteries should be recharged. Further operation of the machine could damage the machine or the batteries. When the machine is left overnight with less than a full charge, the display may initially indicate a full charge.
Operations Scrub Controls 2 1 c 1. Function Mode Dial The first two positions are for transport only. See drive controls section. A1 - Daytime cleaning/light cleaning This mode is used for light cleaning. In this mode the machine will propel at a maximum of medium speed. The scrub deck will automatically lower to a lower down pressure setting. The water will flow at a low rate. Water will automatically shut off in neutral and restart when pressure resumes.
Operations A4 - Heavy scrub level cleaning This mode is used for heavy level cleaning. In this mode the machine will propel at a maximum of slow speed. The scrub deck will lower to a heavy down pressure. The water will flow at a high rate. The vacuum will flow at a high rate. B - Vacuum only mode This mode is used for picking up solution only. The brushes and water will both be up and off. In this mode the machine will propel at a maximum of slow speed.
Operations Machine Operation Filling Solution Tank Pre-Run Machine Inspection Do a pre-run inspection to find possible problems that could cause poor performance or lost time from breakdown. Follow the same procedure each time to avoid missing steps. NOTE: Perform Pre-run Machine Check before operating machine listed in Service Schedule in Maintenance Section. Starting Machine FOR SAFETY: Before starting machine, make sure that all safety devices are in place and operating properly. 1.
Operations Optional Chemical Metering System 1. Fill chemical container and place into console recess. Attach lid. 2. Open rear cover and turn chemical selection knob to chemical manufacturers recommended dilution. 3. Press and hold prime button for 30 seconds or until chemical has filled line to scrub deck. If the machine is allowed to stand in neutral with the scrub deck down, the solutions flow stops and brush motors stop.
Operations To Begin Scrubbing When operating the machine around people, pay close attention for unexpected movement. Use extra caution around children. Lorsque vous utilisez la machine en présence de gens, portez une attention particulière aux mouvements inattendus. Soyez plus prudent, surtout en présence d’enfants. NOTE: The solution flow can be adjusted up or down approximately 10 percent by changing the dip switch settings on the control board.
Operations brushes down to further loosen soil. The additional application of solution will further assist the difficult cleaning job. FOR SAFETY: When using machine, go slow on inclines and slippery services. Solution Tank 1. Remove the recovery tank lid. 2. Pull the solution drain hose from its mounting pocket. Unscrew the cap, then lower hose in direction of drain. 3. Remove the solution tank cap. 4. Flush the solution tank out with clean water and run several gallons of clean water through systems.
Operations Squeegee Disk 3 2 1 1. Squeegee Handle The squeegee handle holds the squeegee in place. 2. Squeegee Hose and Tube The squeegee hose and tube carry the recovered solution to the recovery tank. 3. Squeegee Wheels The squeegee wheels support the squeegee at the correct height and angle to automatically obtain optimum suction. The squeegee requires no adjustment.
Operations Squeegee - Cylindrical 3 1 2 1. Squeegee Knobs The squeegee knobs hold the squeegee in place. 2. Squeegee Hose and Tube The squeegee hose and tube carry the recovered solution to the recovery tank. 3. Squeegee Wheels The squeegee wheels support the squeegee. The height can be adjusted by turning the knobs.
Notes 26 86367610 Chariot CS26
Maintenance Service Schedule BEFORE EACH WORK PERIOD MAINTENANCE Check water level of batteries after charging; add distilled water if necessary. (Wet cell only) Check that recovery lid seals tightly. Visually check for damaged or worn wheels. Check brushes or pads for proper installation. Check vacuum hose connections. Check that squeegee is securely attached. Check for securely attached drain hoses, plug and cap. Check pedal, brake and steering for proper operation.
Maintenance 1 2 3 4 5 7 6 Batteries 1. Rear Cover Latch 2. Rear Cover 3. Battery Connector-Machine 4. Battery Connector-Battery 5. Batteries 6. Battery Tray Liner 7.
Maintenance Batteries (Wet Cell Only) The batteries provide the power to operate the machine. The batteries require regular maintenance to keep them operating at peak efficiency. The machine batteries will hold their charge for long periods of time, but they can only be charged a certain number of times. To get the greatest life from the batteries, charge them when their charge level reaches 25% of a full charge. Use a hydrometer to check the charge level.
Maintenance Checking Battery Specific Gravity Charging Batteries Use a hydrometer to check the battery specific gravity. When servicing machine, avoid contact with battery acid. Lors de l'entretien de la machine, évitez tout contact avec l'acide de batterie. Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging. CHECKING GRAVITY a. Hydrometer Battery b.
Maintenance Use a 36 volt, 20 amp maximum output DC charger which will automatically shut off when the batteries are fully charged. 1. Stop the machine in a clean, well ventilated area next to the charger. 2. Turn “OFF” machine. FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key. 3. Open rear cover, unplug batteries from machine, unlatch battery tray and pull out to expose batteries. Batteries emit hydrogen gas. Explosion or fire can result.
Maintenance Changing Batteries Stop the machine in a clean area next to the charger. Turn off machine. FOR SAFETY: Before leaving or servicing the machine; stop on level surface, turn off machine and remove key. 1. Remove the rear cover. 2. Disconnect battery pack from machine. 3. Unlatch battery tray from machine and pull out to expose batteries. 4. Use the proper size open end wrench to disconnect main ground wire first and secure cable terminal away from batteries. 5.
Maintenance Onboard Charger (Optional) Circuit Breaker must be off before unplugging batteries. Onboard Charger Programming For machines equipped with optional on-board charger. When replacing batteries, charger programming changes may be required. If replacing batteries with same type, (e.g. maintenance free batteries with maintenance free) no programming is required. When batteries with different type (e.g.maintenance free with wet cell), programming change are required.
Maintenance 2 1 Squeegee - Disk 1. Squeegee 2. Squeegee Retainer Knob 2 1 Squeegee - Cylindrical 1. Squeegee 2.
Maintenance Squeegee Blades The front squeegee blade allows solution to pass through channels in the blade into the squeegee assembly while maintaining vacuum to provide lift. The front blade has four wear surfaces and can be rotated for extended life. The front blade should not require regular replacement under normal use. The squeegee is self adjusting. The rear blade wipes the floor to a near dry condition. It is important the rear blade be in good condition to properly do its job.
Maintenance 2 1 6 3 4 5 Scrub Deck - Disk 1. Scrub Deck Aqua-mizer™ 4. Scrub Deck Skirt Brush Strip 2. Aqua-mizer™ Retainer Knob 5. Scrub Brush Motor 3. Scrub Deck Skirt 6.
Maintenance Scrub Brushes There are four different types of brushes available to cover applications from cleaning heavily soiled floors to polishing. A pad driver is also available to take advantage of the many cleaning pads on the market. Please refer to the following to assist in selecting the proper brush or pad for the work at hand. Uncoated Floors Aggressive Grit is a nylon fiber impregnated with silicone carbide grit. It grinds away stain, soil, and removes surface material.
Maintenance Replacing or Installing Scrub Brushes Disk NOTE: Damage to driver or brush could occur if not securely attached. FOR SAFETY: Before leaving or servicing the machine; stop on level surface, turn OFF machine and remove key. 1. Turn machine power off. 2. Open access cover on deck shroud. 3. Locate release lever, press release lever towards front of machine to release brush pad. The pad will drop down when released. Lift deck shroud up and slide brush/pad assembly out. 4.
Maintenance Brush Motor Carbon Brush Replacement Do not use a pressure washer to clean around the brush motors. Use tap pressure only. 1. Scribe alignment mark on motor barrel to motor cap. Remove two bolts. 2. Remove end cap from motor. NOTE: Motors contain two wave washers in cap. Do not lose these. N’utilisez pas de nettoyeur haute pression pour nettoyer autour des moteurs des brosses. Utilisez seulement la pression du robinet.
Maintenance 1 2 3 Scrub Deck - Cylindrical 1. Scrub Deck Skirt 2. Debris Hopper 3.
Maintenance Replacing or Installing Scrub Brushes Cylindrical 1. Turn machine function dial to transport mode, allowing deck to return to “up” position. Turn the machine power off. FOR SAFETY: Before leaving or servicing the machine; stop on level surface, turn OFF machine and remove key. 2. On right and left sides of deck, turn both brush and skirt releases 1/4 turn counter-clockwise. 3. Swing deck skirts out. Remove brush end caps. Slide brushes out the sides of deck. 4.
Maintenance Actuator Scrub Deck Removal / Replacement Scrub Deck Actuator Adjustment FOR SAFETY: Before leaving or servicing machine, stop on a level surface. Turn off machine. To adjust the actuator: The actuator will need to be adjusted when replaced. 1. Remove the two screws that secure actuator spring plate and pull actuator barrel from stud on actuator spring bracket. 2. Remove clevis pin from upper bracket of actuator. 3. Disconnect actuator from wiring harness. 4. Reverse steps to install. 1.
Maintenance Circuit Protection 1 Circuit Breakers 1. MAIN CIRCUIT BREAKER Interrupts the flow of power from batteries in the event of an electrical overload. When the circuit breaker is tripped, it can be reset by pressing the toggle switch. If the circuit breaker continues to trip, the cause of the electrical overload must be corrected.
Maintenance 4 2 6 1 5 3 Solution 1. Strainer 2. Solution Cap 3. Solenoid Valve 4. Chemical Bottle (Optional) 5. Chemical Pump (Optional) 6.
Maintenance Solution Strainer Located in bottom of tank. Protects system from debris. Solenoid Valve The solenoid valve is mounted on the front of the scrub deck, on left side. The solenoid valve opens and closes to meter the correct amount of solution to the scrub deck. The solenoid valve shuts off solution flow to scrub deck whenever scrubbing stops. To repair or replace solenoid valve, remove screws that secure it to deck. Chemical Bottle (Optional) Holds chemical for optional metering system.
Maintenance 1 3 2 Vacuum 1. Recovery Tank Float Shut-off 2. Vacuum Motor 3.
Maintenance Recovery Tank Float Shut-off When water is no longer being vacuumed from the floor and the vacuum fan is operating, the ball float has engaged. The vacuum motor will not vacuum water with recovery tank full. The recovery tank must be drained. Vacuum Motor Carbon Brushes End Cap 1. The float shut-off screen can be cleaned in or out of the machine. Carbon Brushes 2. To clean the float shut-off while it is inside the machine wipe material off screen then rinse.
Maintenance Drive Motor 1. Drive Motor 2.
Maintenance Electric Parking Brake Engagement FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and remove key. Electric Brake Engagement Drive Motor Carbon Brush Replacement Do not use a pressure washer to clean around the motors. Use tap pressure only. This machine is equipped with an electric parking brake. The brake automatically engages and keeps the machine from moving whenever the operator steps off the platform or when emergency stop is engaged.
Maintenance Transporting Preparation for Loading/Unloading Trailer Pushing Machine The machine may be pushed for short distances at speeds not to exceed 5 mph. Be careful to avoid damaging machine. The machine may be pushed by hand from the rear. NOTE: To avoid damage caused by regenerative voltage, disconnect traction motor before towing or pushing machine.
Maintenance Troubleshooting PROBLEM No power to machine Little or no propel CAUSE Battery disconnected Emergency shut-off activated Battery cables corroded Faulty key switch On board charger plugged in Main circuit breaker tripped Low battery charge Machine turned on with pedal not in neutral position Tripped circuit breaker Wheels spin Controller overheated Faulty drive reset circuit or switch Faulty platform circuit or switch Faulty speed control circuit or switch Check wires & connections Faulty for
Maintenance PROBLEM Vacuum motor does not run, or runs slowly Squeegee will not go up/down Poor scrubbing performance Little or no solution flow to the floor Brush motors do not run, or run slowly CAUSE Faulty vacuum circuit or switch Check wires connections and motor Worn vacuum motor brushes Faulty circuit or actuator Faulty cables or pulleys Debris caught in scrub brushes Worn brushes or pads Replace brushes, check commutator Check wires, connectors and actuator Repair/replace cables or pulleys Re
Maintenance Controller Fault Codes ERROR CODE DELUXE PROBLEM SOLUTION LOW BATTERY VOLTAGE THE BATTERY NEEDS CHARGING OR THERE IS A BAD CONNECTION TO THE BATTERY TRACTION MOTOR DISCONNECTED THE TRACTION MOTOR HAS A BAD CONNECTION, CHECK CONNECTIONS TO MOTOR TRACTION MOTOR CIRCUIT SHORT THE TRACTION MOTOR HAS A SHORT CIRCUIT TO THE BATTERY AUX FAULT or ACTUATOR (DECK or SQUE) CHECK AUX OUTPUT DEVICES, CHECK ALL ASSOCIATED WIRING TO AUX DEVICES OVERCURRENT VACUUM MOTOR TRIP THE VACUUM MOTOR HAS E
Notes 54 86367610 Chariot CS26
Parts Parts 86367610 Chariot CS26 55
Bumper 4 1 5 2 3 56 86367610 Chariot CS26
Bumper REF PART NO. QTY 1 2 3 4 5 86361960 86361950 86359000 86358960 86276890 2 2 1 1 2 DESCRIPTION SERIAL NO. FROM NOTES SCR, 5/16-18 X 3.0 PTHMS SS SCR, 5/16-18 X 2.
Console 12 19 11 8 5 4 1 15 23 22 14 3 9A 9B 9C 9D 6 17 25 26 13 18 16 10 24 21 7 58 20 2 86367610 Chariot CS26
Console REF PART NO. QTY 1 2 3 4 5 6 7 8 9A 9B 9C 9D 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 86005620 86199840 86272020 86361770 86361760 86361410 86360770 86360700 86367990 86368010 86368000 86359210 86006530 86360260 86360140 86359560 86359220 86359100 86359090 86359050 86359020 86324210 86323300 86279610 86161800 86277620 86273750 86010650 86329570 1 1 2 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 2 1 2 1 2 2 DESCRIPTION NUT, 1/4-20 X .
Console Mounting 5 6 1 3 4 2 60 86367610 Chariot CS26
Console Mounting REF PART NO. QTY 1 2 3 4 5 6 86360300 86276490 86010670 86360290 86367960 86367250 1 5 5 1 2 2 DESCRIPTION SERIAL NO. FROM NOTES BRKT, CONSOLE MT LT SCREW 5/16-18 X 5/8 HHCS SS WASHER 5/16 FLAT SS BRKT, CONSOLE MT RT SCR, 5/16-18 X 1.38 HHCS SS WASHER, .344ID X 1.13OD X .
Control Panel - Upper 19 2 10 8 18 10 6 11 1 3 7 15 4 13 14 5 17 11 9 12 16 62 86367610 Chariot CS26
Control Panel - Upper REF PART NO. QTY DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 86362590 86360690 86358440 86358430 86354870 86354810 86354560 53217380 86315470 86295200 86292780 86292590 86255900 86198460 86012670 86007190 86005640 63130140 86367100 1 1 2 2 1 1 1 1 1 2 2 1 6 2 1 1 2 1 1 SWITCH, SPDT 3 POSN MOM, ARROW PANEL, CONTROL UPPER, CS26 O-RING, 4MM ID, 1.
Control Panel-Lower 1 6 3 9 13 5 12 2A 2B 15 14 16 17 11 10 4 7 18 19 64 86367610 Chariot CS26 8
Control Panel-Lower REF PART NO. QTY DESCRIPTION 1 2A 2B 3 4 5 6 7 8 9 10 11 12 13 14 15 16 86366910 86370780 86370510 86361870 86361520 86361420 86360890 86360880 86369020 86006620 86270920 86275260 86255910 86255900 86006850 86005710 86005640 1 1 1 1 4 1 1 1 1 2 4 2 1 2 1 4 2 17 86006760 1 18 86369480 1 19 86271910 1 PANEL, LOWER. CS26 KIT, PICDUO CONTROLLER PICDUO ASSEMBLY, MC, CS26SP CONTROLLER, I-DRIVE CS26 CLIP, CABLE ENTRY HINGE, PANEL GASKET, .125 X .31 X 23.
Control Panel Mounting 1 1 2 66 86367610 Chariot CS26
Control Panel Mounting REF PART NO. QTY 1 2 86371410 86172980 12 3 DESCRIPTION SERIAL NO. FROM NOTES SCR, 10-32 X .
Decals 68 86367610 Chariot CS26
Decals REF PART NO. QTY 1 2 3A 3B 4A 4B 5 6 7 86361790 86361800 86362780 86370090 86362790 86370100 86004970 86362160 86362940 1 1 1 1 1 1 1 1 1 DESCRIPTION LABEL, CS26, CONTROL, LEFT LABEL, CS26 CONTROL, RIGHT LABEL, CS26, SIDE, LEFT LABEL, CS26SP, SIDE, LEFT LABEL, CS26, SIDE, RIGHT LABEL, CS26SP, SIDE, RIGHT LABEL WINDSOR LOGO DOMED LABEL, CHEMICAL METERING LABEL, BATTERY CABLING 86367610 Chariot CS26 SERIAL NO.
Drive Mounting 70 86367610 Chariot CS26
Drive Mounting REF PART NO. QTY DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 - 86366140 86366130 86364130 86361070 86218360 86357870 86357120 86270990 86264940 86357130 64358540 86223980 66132310 4 4 1 1 1 1 1 1 3 1 1 2 - M10 X 25MM, FLANGE HH BOLT, GR 10.9 3/8-16 X 1, FLANGE HH BOLT, GR 8 ASM, SHAFT DRIVE MOTOR BRKT, WIRING, DRIVE UNIT GROMMET, 3/4 ID X 7/8 GROOVE ASM, BEARING BLOCK, FRT DRIVE HUB, DRIVE WHEEL MOTOR, 36V NUT, 10-32 HEX NYLOCK SS CABLE TIE, 11.
Frame 3 9 3 13 12 1 14 10 11 5 15 2 6 5 4 8 10 7 72 86367610 Chariot CS26
Frame REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 86360820 86360710 86358190 86357950 86277410 86276890 86276490 86010670 86400810 86368240 86361210 86005770 86006640 86270830 86368730 1 1 2 2 6 6 2 2 6 6 2 2 2 2 1 DESCRIPTION ASSY, MAIN SUPPORT, CS26 ASM, WHEEL GUARD GLIDE, BATTERY TRAY PAD, TIP SCR, 5/16-18 X 5/8 CARRIAGE SS SCREW 5/16-18X3/4 PTHMS SS SCREW 5/16-18 X 5/8 HHCS SS WASHER 5/16 FLAT SS SCREW, 1/4-20 X .75 PHFLHMS SS NUT,5/16-18, FLGNYLOCK,SS SCR, 3/8-16 X 0.
Platform 14 2 1 3 18 4 5 7 8 9 6 6 10 12 6 17 10 16 11 10 7 13 5 8 15 74 86367610 Chariot CS26
Platform REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 86359080 86318010 86318000 86361170 86279170 86172980 86254970 86327510 86198440 86264930 86361060 86311560 86005810 86007010 86327910 86007110 86361160 86264940 1 1 1 1 6 10 3 3 6 2 1 1 2 2 4 1 1 2 DESCRIPTION SERIAL NO. FROM NOTES PLATFORM, OPERATOR PEDAL, HEEL PEDAL, ACCELERATOR PIN, DOWEL, .25D X 3.125", STEEL WASHER, #10 X 1.
Platform Footbox & Rear Wheels 76 86367610 Chariot CS26
Platform Footbox & Rear Wheels REF PART NO. QTY DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 86361130 86271840 86361140 86358000 86361120 86357990 86232130 86335520 86326490 86361150 86224320 86008710 2 4 4 1 1 1 2 2 4 2 4 2 PLATE, PLATFORM SUPPORT NUT 5/16-18 HEX NYLOCK THIN SS SPACER, 1.50 X .625OD X .065" WALL FOOTBOX, OPERATOR PLATFORM COLLAR, SHFT 1"ID X 1-5/8"OD X 5/8" AXLE, REAR CAP 2.75 ID X 1.0 L BLK VINYL WHEEL, 10 X 2.5, PLSTC HUB, W/BEARINGS SCR, 5/16+18 X 3.
Rear Cover 1 2 4 78 86367610 Chariot CS26 3
Rear Cover REF PART NO. QTY 1 2 3 4 86277620 86161800 86359070 86272020 2 1 1 2 DESCRIPTION SERIAL NO.
Scrub Deck - Disk 12 1 11 2 3 4 5 6 7 8 10 A TORQUE 84 IN/LBS 80 86367610 Chariot CS26 A
Scrub Deck - Disk REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 86361810 86368290 86008710 86361580 86010790 86276970 86279530 86003420 86392260 86392270 86264940 86002830 2 2 1 8 8 2 2 2 2 1 2 DESCRIPTION MOTOR ASM, 36VDC 300RPM GEAR BRUSH SET, 86361810 MOTOR RING 3/4" EXT SNAP H-D PLATE, MOTOR MOUNT WASHER 3/8 SPLIT LOCK PLTD SCREW 3/8-16 X 3/4 HHCS WASHER .765IDX1.31ODX.09T SS DRIVER, BRUSH SD WASHER, WAVE, 3/4, STL OPEN ASM, SCR, TENSION, 5/16 CABLE TIE 11.38" UL/CSA CABLE TIE .375 X 24.
Scrub Deck - Cylindrical 46 41 23 35 29 34 24 2 17 9 13 47 25 36 40 39 23 17 27 26 4 3 6 15 1 11 5 10 28 38 18 19 12 18 16 7 8 40 21 37 39 34 30 20 26 21 23 38 10 33 14 32 7 8 16 18 31 44 42 5 11 12 19 4 15 13 17 18 6 9 56 58 51 52 55 52 48 54 50 49 57 82 86367610 Chariot CS26 45 3 1 43 2 22 23 35
Scrub Deck - Cylindrical REF PART NO.
Scrub Deck Lift - Disk 1 2 5 6 3 8 7 4 9 10 13 12 11 14 3 84 86367610 Chariot CS26
Scrub Deck Lift - Disk REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 86365440 86008660 86005630 86255450 86275510 86010770 86011950 86273850 86010780 86005810 86361710 86274110 86361720 86002830 1 1 4 2 2 2 1 2 2 2 1 2 1 1 DESCRIPTION SERIAL NO. FROM NOTES PIN, CLEVIS 5/16 X 2.25 PL COTTER 5/16" RING NUT 3/8-16 HEX NYLOCK THIN SS SPRING .96D X 4.0L X.135W SCREW 3/8-16 X 4.5" HHCS GR5 WASHER 7/16ID X1DX.08 FLT SS ACTUATOR, 36VDC 3.
Scrub Deck Lift - Cylindrical 86 86367610 Chariot CS26
Scrub Deck Lift - Cylindrical REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 86370800 86370720 86370280 86370270 86370260 86270250 86370240 86368240 86367250 86320880 86276950 86276490 86272620 86270990 86228790 86010630 86008650 86360310 86008660 86006200 1 1 1 1 1 1 1 2 2 1 2 2 1 1 2 2 2 4 1 1 DESCRIPTION SERIAL NO. FROM NOTES BRKT, SOLENOID CS26 SP PLATE, CYL DECK ATTACHMENT BRKT, LIFT MOUNT, RH BRKT, LIFT MOUNT, LH ASM, DECK LIFT BRKT, ACTUATOR MOUNT PIN, CLEVIS 1/4 X 2.
Scrub Deck Skirts 1 2 3 5 6 7 8 9 9 11 10 15 4 12 13 14 88 86367610 Chariot CS26
Scrub Deck Skirts REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 86358580 86361590 86005810 86364880 86006870 86335450 86358570 86358560 86273810 86358620 86242130 86270990 86358630 86361670 86361680 1 1 6 7 2 2 2 1 10 1 4 7 1 1 1 DESCRIPTION SERIAL NO. FROM NOTES SKIRT, SCRUB DECK, 26" IN FLEX STRIP BRUSH, 26" SKIRT NUT 1/4-20 HEX NYLOCK SS SCREW, 10-32 X 5/8, PH, CSKH, SS SCREW #10B X 1/2 PHSM BLK WASHER, #10 X.75ODX.
Scrub Deck Mounting - Disk 3 1 5 1 2 4 3 5 2 4 7 5 6 4 8 5 4 3 6 1 90 2 86367610 Chariot CS26 3 2
Scrub Deck Mounting - Disk REF PART NO. QTY 1 2 3 4 5 6 7 8 86276920 86278910 86008460 86009050 86005630 86361570 86276470 86224380 6 8 8 8 8 4 2 2 DESCRIPTION SERIAL NO. FROM NOTES SCREW 3/8-16X1 WASHER,3/8IDX7/8ODSS SPACER, .500OD X .391ID X .400 BEARING 1/2 ID X 11/32L NYLON NUT 3/8-16 HEX NYLOCK THIN SS LINKAGE, DECK, 1.00 X .25THK SCREW, 3/8-16 X 2.25 HHCS SS SPACER, 1 OD X .391 ID X 1.
Scrub Deck Mounting - Cylindrical 3 1 3 1 5 4 3 4 2 92 86367610 Chariot CS26
Scrub Deck Mounting - Cylindrical REF PART NO. QTY 1 2 3 4 5 86370830 86370120 86276890 86368240 73031070 4 4 2 6 3 DESCRIPTION SERIAL NO. FROM NOTES SCREW, 5/16-18 X 2.0, PNH, MS, SS SPACER, .32 ID X .75D X .75L, AL SCREW, 5/16-18 X .75 PHTRHMS SS NUT, 5/16-18, FLGNYLOCK,SS SCREW, 5x16 -10.
Scrub Brush/Pads Driver - Disk 7 5 6 9 4 8 7 6 5 9 1 4 8 2A 2B 2C 5 3 94 86367610 Chariot CS26
Scrub Brush/Pads Driver - Disk REF PART NO. QTY 1 2A 2B 2C 3 4 5 6 7 8 9 86000210 86000220 86000230 86000240 86005070 86276590 86276580 86276600 86007910 86007280 86005940 2 2 2 2 1 3 4 3 1 1 1 DESCRIPTION SERIAL NO. FROM NOTES PAD DRIVER, 13" SD BRUSH, 13" POLY SD BRUSH, 13" NYLON SD BRUSH 13" MILD GRIT SD LOCK PAD CENTER SNAP,TWO STEP SCR, #12X1 PPHSMS SS SCR, 8-32 X 3/4 PTHMS SS SCR, #10 X 3/4 PTHSMS SS SPRING EXT .31D X 2.0L X .
Scrub Brush/Pads Driver - Cylindrical 96 86367610 Chariot CS26
Scrub Brush/Pads Driver - Cylindrical REF PART NO. PRV NO. QTY 1A 1B 1C 1D 1E 69069350 69069810 69069820 69069830 69069840 - - DESCRIPTION ROLLER BRUSH ROLLER BRUSH ROLLER BRUSH ROLLER BRUSH ROLLER BRUSH SERIAL NO.
Solution System - Disk 7 4 5 9 3 7 13 2 8 11 1 10 6 12 98 86367610 Chariot CS26
Solution System - Disk REF 1 2 3 4 5 6 7 8 9 10 11 12 13 PART NO. QTY 86280910 86366100 86363970 86362980 86362970 86264940 86281330 86271830 86264940 86233150 86197940 86006520 86001550 1 1 1 1 1 1 2 2 1 2 1 2 2 DESCRIPTION SERIAL NO. FROM NOTES HOSE, 1/2ID WIREBOUND X 23" VALVE, 36V SOL, 1/2 BARB HOSE, 1/2ID WIREBOUND X 8.25" ELBOW, 1/4FPT X 1/2BARB 90 DEG NYL TEE, 1/4 MPT X 3/8 BARBS, NYL CABLE TIE 11.38" UL/CSA HOSE, 3/8ID WIREBOUND X 4" NUT, 3/8 NPT PLASTIC CABLE TIE, 11.
Solution System - Cylindrical 8 7 2 6 3 5 4 100 86367610 Chariot CS26 1
Solution System - Cylindrical REF 1 2 3 4 5 6 7 8 PART NO. QTY 86368310 86366100 86302770 86233150 86197940 86006520 54433750 63621700 1 1 1 4 1 2 1 1 DESCRIPTION SERIAL NO. FROM NOTES HOSE, 1/2ID WIREBOUND X 17.
Squeegee - Disk 10 5 8 32 4 23 28 35 23 26 12 36 7 31 25 30 27 22 9 34 1 24 15 19 20 6 21 33 11 16 29 3 14 2 18 13 17 102 86367610 Chariot CS26
Squeegee - Disk REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 PART NO.
Squeegee - Cylindrical 8 11 9 12 10 13 7 14 15 17 1 3 4 5 22 16 21 6 2A 2B 2C 23 104 86367610 Chariot CS26 20 19 18
Squeegee - Cylindrical REF PART NO. PRV NO.
Squeegee Lift 3 5 10 17 24 12 15A 15B 19 22 26 SEE DETAIL 'A' 2 6 4 7 26 23 16 19 11 29 20 13 9 27 27 14 8 18 21 26 17 23 'A' 106 25 1 28 27 86367610 Chariot CS26
Squeegee Lift REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15A 15B 16 17 18 19 20 21 22 23 24 25 26 27 28 29 86364040 86364030 86364020 86362820 86362310 86362300 86362290 86362270 86362260 86362250 86362240 86362230 86362220 86362210 86354470 86370440 86320880 86317330 86273810 86273750 86272620 86272470 86272330 86271870 86270870 86264920 86010630 86008650 86006560 86005630 1 1 1 1 3 1 1 2 1 1 1 1 1 1 1 1 1 2 1 6 1 2 1 2 2 1 9 4 1 1 DESCRIPTION BUSH, PLN,.251 X .313 X .
Squeegee Swing - Disk 12 10 1 18 15 17 16 6 20 22 11 16 8 16 21 13 9 23 24 19 7 5 4 3 2 14 108 86367610 Chariot CS26
Squeegee Swing - Disk REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 86365530 86364110 86363080 86363060 86363050 86362690 86362370 86362360 86362350 86361730 86358220 86354300 86273830 86273820 86271840 86271560 86271430 86264940 86368800 86010670 86010630 86009080 86008650 86259420 1 2 1 2 1 1 2 2 2 1 1 1 4 2 2 4 2 1 4 2 4 2 1 4 DESCRIPTION SERIAL NO. FROM NOTES CLAMP, RATCHET, 2.13D SCR, 5/16-18 X 3.
Squeegee Swing - Cylindrical 19 14 2 12 20 17 13 6 4 16 8 7 15 3 18 9 10 1 5 11 110 86367610 Chariot CS26
Squeegee Swing - Cylindrical REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 86370640 86370630 86370620 86370610 86367250 86362360 86361770 86272620 86320680 86277470 86276780 86273750 86271560 86271430 86270830 86228790 86009080 86008650 86354300 86365530 1 1 1 2 2 2 1 1 1 1 2 4 4 2 1 4 2 1 1 1 DESCRIPTION SERIAL NO. FROM NOTES BRKT, SQUEEGEE MOUNT PLATE, SQUEEGEE PIVOT PLATE, CABLE PIN ARM, SQUEEGEE PIVOT WASHER, .344 X 1.13 X .
Steering 28 29 13 6 15 4 21 30 16 33 24 32 11 3 31 5 20 18 12 24 9 25 19 27 7 10 23 1 8 34 26 12 17 2 22 14 112 86367610 Chariot CS26
Steering REF PART NO.
Tank 12 10 4 11 22 13 16 5 20 2 8 7 6 23 9 18 15 24 3 17 19 21 25 14 1 26 27 114 86367610 Chariot CS26
Tank REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 PART NO. QTY 86367250 86366450 86362380 86361920 86361780 86361770 86361760 86360780 86360650 86360640 86360630 86359060 86358680 86354270 86353950 86327510 86314080 86277480 86276490 86271940 86010670 86007970 86005620 86002390 86002380 86279130 86276780 4 1 1 1 1 2 1 1 1 2 1 1 1 1 1 1 2 2 4 1 4 1 1 1 1 4 4 DESCRIPTION SERIAL NO. FROM NOTES WASHER, .344IDX1.130ODX.
Vacuum 9 13 14 8 5 7 1 15 14 10 4 11 6 2 12 116 86367610 Chariot CS26 3
Vacuum REF PART NO. QTY DESCRIPTION 1 86360990 1 2 86360320 2 3 4 5 6 7 8 9 10 11 12 13 14 15 86360310 86360270 86359040 86359030 86358110 86327500 86326980 86317630 86312920 86280990 86276350 86270770 86002390 86002380 3 1 1 1 1 3 1 4 1 1 1 1 2 1 HOSE, 1.5 BLK VAC X 40” SCR, SET 1/4-20X3 HEX SKT CUP PT SS NUT, 1/4-20 FLG SS NYL GASKET, .188 X .31 X 22.
Wiring-Batteries 3 10 9 4 7 12 13 6 11 8 2 9 5 1A 1B 1C 14 15 16 19 18 17 118 86367610 Chariot CS26
Wiring-Batteries REF PART NO. QTY 1A 1B 2B 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 86283410 86228430 86228410 86273980 86271910 86270890 86264960 86260610 86260230 86260200 86233360 86010670 86010650 86008920 86008760 86359250 86359500 86272810 86254990 86092910 86360020 3 3 3 1 6 1 2 1 1 2 1 6 1 6 1 1 1 1 1 1 2 DESCRIPTION SERIAL NO.
Wiring-Components 2 2 1 2 2 1 5 6 7 8 9 4 3 8 120 86367610 Chariot CS26
Wiring-Components REF PART NO. QTY 1 2 3 4 5 6 7 8 9 86361230 86361220 86326270 86264940 86239720 86238500 86238430 86006590 86198460 2 4 1 1 1 1 2 2 1 DESCRIPTION SERIAL NO. FROM NOTES CLAMP, PAN 3/4" CLAMP, PAN 1-1/4" CLAMP, 1.5 DIA CABLE TIE 11.38" UL/CSA HORN, 108DB MINATURE W/RING GROMMET,1.703IDX2.5.ODX.125GRV GROMMET 1.
Wiring 1 122 86367610 Chariot CS26
Wiring 1 REF 1 2 3 PART NO. QTY 86356760 86366540 86367100 1 1 1 DESCRIPTION SERIAL NO.
Wiring 2 Disk 124 86367610 Chariot CS26
Wiring 2 Disk REF PART NO.
Wiring 2 Cylindrical 126 86367610 Chariot CS26
Wiring 2 Cylindrical REF PART NO.
Wiring 3 128 86367610 Chariot CS26
Wiring 3 REF A1 A2 G1-G3 M1 M2 M3 M4 M5 M6 S0 S1 S3 S4 S5 S6 S7 Q1 Q2 V8 Y1 Y2 U1 V10 V9 H1 H2 F1 F2 X12/X13/X14/X15 X9/X10/X11 DESCRIPTION IDRIVE CONTROL CPU CONTROL BATTERY 12V BRUSH MOTOR BRUSH MOTOR TRACTION MOTOR VACUUM MOTOR DECK ACTUATOR SQUEEGEE ACTUATOR E STOP KEY SWITCH F/R SWITCH PLATFORM SWITCH WATER SWITCH HORN SWITCH PRIME SWITCH MAIN ROTARY CHEM ROTARY HOUR METER BRAKE WATER SOLENOID CHEM PUMP OPTION FLOW METER OPTION TRUECHARGE WATER LED HORN PCB 60A - U2 IDRIVE 60A - U2 DEUTSCH CONNECTOR
Wiring 4 130 86367610 Chariot CS26
Wiring 4 REF A1 A2 G1-G3 M1 M2 M3 M4 M5 M6 S0 S1 S3 S4 S5 S6 S7 Q1 Q2 V8 Y1 Y2 U1 V10 V9 H1 H2 F1 F2 X12/X13/X14/X15 X9/X10/X11 DESCRIPTION IDRIVE CONTROL CPU CONTROL BATTERY 12V BRUSH MOTOR BRUSH MOTOR TRACTION MOTOR VACUUM MOTOR DECK ACTUATOR SQUEEGEE ACTUATOR E STOP KEY SWITCH F/R SWITCH PLATFORM SWITCH WATER SWITCH HORN SWITCH PRIME SWITCH MAIN ROTARY CHEM ROTARY HOUR METER BRAKE WATER SOLENOID CHEM PUMP OPTION FLOW METER OPTION TRUECHARGE WATER LED HORN PCB 60A - U2 IDRIVE 60A - U2 DEUTSCH CONNECTOR
Wiring 5 132 86367610 Chariot CS26
Wiring 5 REF A1 A2 G1-G3 M1 M2 M3 M4 M5 M6 S0 S1 S3 S4 S5 S6 S7 Q1 Q2 V8 Y1 Y2 U1 V10 V9 H1 H2 F1 F2 X12/X13/X14/X15 X9/X10/X11 DESCRIPTION IDRIVE CONTROL CPU CONTROL BATTERY 12V BRUSH MOTOR BRUSH MOTOR TRACTION MOTOR VACUUM MOTOR DECK ACTUATOR SQUEEGEE ACTUATOR E STOP KEY SWITCH F/R SWITCH PLATFORM SWITCH WATER SWITCH HORN SWITCH PRIME SWITCH MAIN ROTARY CHEM ROTARY HOUR METER BRAKE WATER SOLENOID CHEM PUMP OPTION FLOW METER OPTION TRUECHARGE WATER LED HORN PCB 60A - U2 IDRIVE 60A - U2 DEUTSCH CONNECTOR
Wiring 6 134 86367610 Chariot CS26
Wiring 6 REF A1 A2 G1-G3 M1 M2 M3 M4 M5 M6 S0 S1 S3 S4 S5 S6 S7 Q1 Q2 V8 Y1 Y2 U1 V10 V9 H1 H2 F1 F2 X12/X13/X14/X15 X9/X10/X11 DESCRIPTION IDRIVE CONTROL CPU CONTROL BATTERY 12V BRUSH MOTOR BRUSH MOTOR TRACTION MOTOR VACUUM MOTOR DECK ACTUATOR SQUEEGEE ACTUATOR E STOP KEY SWITCH F/R SWITCH PLATFORM SWITCH WATER SWITCH HORN SWITCH PRIME SWITCH MAIN ROTARY CHEM ROTARY HOUR METER BRAKE WATER SOLENOID CHEM PUMP OPTION FLOW METER OPTION TRUECHARGE WATER LED HORN PCB 60A - U2 IDRIVE 60A - U2 DEUTSCH CONNECTOR
Notes 136 86367610 Chariot CS26
Options Options 86367610 Chariot CS26 137
Chemical Metering Solution System - Disk 10 19 11 22 14 15 28 4 21 25 2 3 20 8 9 12 24 13 5 17 18 27 18 16 23 7 138 26 86367610 Chariot CS26 1 6
Chemical Metering Solution System - Disk REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 - 64290380 86364390 40354760 86363990 86363980 86363970 86363960 86363950 86363940 86363900 86363890 86363880 86362980 86362970 86362850 86362840 86001550 86361690 86281330 86006520 86361230 86359010 86271850 86271830 86264940 86264930 86233150 86197940 86006580 86369920 86370450 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 2 1 1 1 2 1 3 4 1 1 - DESCRIPTION SERIAL NO.
Chemical Metering Solution System - Cylindrical 8 9 16 10 11 13 4 15 20 12 2 3 14 7 18 24 23 22 19 21 5 18 1 SCALE: 1.
Chemical Metering Solution System - Cylindrical REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 - 64290380 86364390 40354760 86363990 86363980 86363950 86363940 86371740 86363890 86363880 86362850 86362840 86361690 86006520 86361230 86359010 86271850 86264930 86233150 86197940 86006580 86370840 86302770 54433750 63621700 86369920 86370450 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 3 6 1 1 1 1 1 1 - DESCRIPTION SERIAL NO.
Control Panel - Chemical Solution Metering 2 19 17 8 16 13 11 10 14 24 12 6 9 18 3 5 15 23 26 25 1A 1B 4 27 21 28 29 22 7 20 142 86367610 Chariot CS26
Control Panel - Chemical Solution Metering REF PART NO.
Onboard Charger 15 11 7 1 14 12 3 8 4 9 6 18 17 16 13 5 10 2 144 86367610 Chariot CS26
Onboard Charger REF PART NO. QTY DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 86366080 86363800 86361440 86361430 86361090 86361080 86360460 86307990 86277640 86256180 86005710 86005700 86005670 86005640 86369470 86005810 86371560 86273740 4 1 1 1 1 1 1 1 2 1 2 3 1 2 1 1 1 1 STANDOFF, 10-32 X 1.
Battery Exchange - 1 12 12 2 21 16 11 8 23 22 5 DETAIL A 7 21 6 4 25 19 24 26 20 21 15 11 1 13 21 SEE DETAIL A 10 7 9 14 18 17 11 146 86367610 Chariot CS26 3
Battery Exchange - 1 REF PART NO.
Battery Exchange - 2 4 9 7 15 10 12 7 10 15 16 8 2 6 14 15 7 13 11 9 13 17 8 7 7 15 7 8 11 13 1 3 6 5 5 148 86367610 Chariot CS26
Battery Exchange - 2 REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 86359440 86359430 86359420 86359410 86277470 86276070 86270830 86259420 86259410 86259400 86254280 86231150 86228840 86226830 86010670 86007020 86006560 1 2 2 2 4 2 10 6 4 4 4 2 6 2 8 2 2 DESCRIPTION SERIAL NO. FROM NOTES BRACKET, PEDAL, CART PLATE, LATCH LINK, CART PLATE, PEDAL LINK, CART PLATE, LATCH, CART SCR, 5/16-18 X 1.5 CARRIAGE SS SCR, 5/16-18 X 3/4 CARRIAGE SS NUT, 5/16-18 HEX NYLOCK SS WASHER, THRUST.
Battery Exchange - 3 13 14 15 2X EXISTING NUTS 7 10 (LEFT) 11 (RIGHT) 8 9 12 6 4 5 150 86367610 Chariot CS26 3 1 (LEFT) 2 (RIGHT)
Battery Exchange - 3 REF PART NO. QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 86360040 86360050 86319670 86363760 86010670 86007020 86279190 86360090 86298200 86360060 86360070 86254890 86010670 86270830 86273780 1 1 2 2 2 2 2 2 2 1 1 2 2 2 2 DESCRIPTION SERIAL NO. FROM NOTES BATTERY STOP, LEFT BATTERY STOP, RIGHT SLEEVE, BEARING PLATE, SHIM .030" THIC WASHER 5/16 FLAT SS SCREW, 5/16-18 X 1.25 HHCS SS NP WASHER, 10 FLT TYPEB FLT ZNPLT STANDOFF, RND, 3/8 OD, 10-32 X3/8 STANDOFF, .43 OD, 1/4-20 X.
Suggested Spare Parts PART NO. 86161800 86362390 86359580 86359570 86359590 86360270 86360990 86280990 86312920 86353950 86354270 86361590 86361670 86361680 152 SERIAL NO. FROM DESCRIPTION LATCH & CONCEALED KEEPER CASTER, SWIVEL 2” WHEEL BLADE, SQUEEGEE, FRONT BLADE, SQEEGEE, REAR WHEEL, 2.0 OD X .31 ID X .875 GRY GASKET, .188 X .31 X 22.8 HOSE, 1.
Serial Numbers REF. MODEL: SERIAL # NO.
