® iExtract® MODELS: CE24 10060140 Operating Instructions (ENG) CE24X 10060150 CEE24 10060160 Read these instructions before using the machine 86037880-BW 11/29/12
MACHINE DATA LOG/OVERVIEW OVERVIEW The Chariot iExtract® is a battery powered, stand-on, carpet extractor intended for commercial use. The Chariot iExtract® applies a cleaning solution onto a carpeted floor, sweeps and scrubs the carpet with two counter-rotating brushes and then vacuums the soiled water back into the recovery tank. The brushes also help to raise the pile of the carpet, giving it a lush groomed appearance. Warranty Registration Thank you for purchasing a Windsor product.
TABLE OF CONTENTS Machine Data Log/Overview................................2 Table Of Contents ................................................3 HOW TO USE THIS MANUAL How To Use This Manual.....................................1-1 SAFETY Important Safety Instructions ............................ 2-1 Hazard Intensity Level....................................... 2-2 Safety Label Location........................................ 2-3 OPERATIONS Technical Specifications....................................
HOW TO USE THIS MANUAL This manual contains the following sections: - HOW TO USE THIS MANUAL SAFETY OPERATIONS MAINTENANCE PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authorized Windsor dealers. When placing an order for parts, the machine model and machine serial number are important. Refer to the MACHINE DATA box which is filled out during the installation of your machine.
IMPORTANT SAFETY INSTRUCTIONS When using an battery powered appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Use only indoors. Do not use outdoors or expose to rain. Use only as described in this manual. Use only manufacturer’s recommended components and attachments.
HAZARD INTENSITY LEVEL The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
SAFETY LABEL LOCATION NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them.
TECHNICAL SPECIFICATIONS ITEM Nominal Power Rated Voltage Rated Amperage Batteries Battery Compartment Dimensions Propelling Motor Mass (GVW) Weight Empty Without Batteries Solution Control Spray Pump Pressure Solution Capacity Spray Jets Recovery Capacity Vacuum Motors Maximum Flow Rate of Vacuum Motor Maximum Suction Of Vacuum Motor Scrub Brush Diameter Scrub Brush Motors Scrub Brush Pressure Scrub Brush Speed Tires Extracting Speed 1 Extracting Speed 2 Maximum (Transport) Speed Frame Construction Brake M
TECHNICAL SPECIFICATIONS ITEM Height Length Width Width of scrub path MEASURE 50.6 inches (1285 mm) 52.5 inches (1330 mm) 26.5 inches (670 mm) 23 inches (585 mm) WIDTH LENGTH SPECIAL NOTES: The sound pressure level at the operator’s ear was measured to be 70 dBA. This was a nearfield, broadband measurement taken in a typical industrial environment on a tile floor. This appliance contains no possible source of impact noise. The instantaneous sound pressure level is below 63 Pa.
HOW THIS MACHINE WORKS The Chariot iExtract® is a battery powered, selfpropelled Carpet Extractor intended for commercial use. The machine is designed to apply a cleaning solution onto carpeted floor, sweep and scrub the carpet with two counter-rotating brushes, then vacuum the soiled water back into the recovery tank. The machine's primary systems are the solution system, scrub system, recovery system and operator control system.
COMPONENTS 1 2 9 3 11 5 6 12 7 4 1. 2. 3. 4. 5. 6. 8 Control Panel-Drive Control Panel-Scrub Control Housing Pedal Platform Rear Cover Tank 10 7. Scrub Deck 8. Vacuum Shoes 9. Recovery Dome 10. Recovery Drain Hose 11. Solution Cover 12.
DRIVE CONTROLS 10 2 8 6 3 7 11 1 9 5 3-5 4 86037880 CHARIOT EXTRACTOR 01/16/07
DRIVE CONTROLS 1. 2. 3. 4. 5. 6. Key Switch Emergency Stop/Brake Switch Directional Control Switch Throttle Pedal Operator Presence PedalPrior to Serial Number (11*) Speed Control Switch 7. 8. 9. 10. 11. Drive Reset Switch Horn Button Steering Wheel Battery Discharge Indicator Hour Meter 1. KEY SWITCH Controls the power for machine functions. To turn the machine power on, rotate key clockwise. To turn the machine off, rotate key counterclockwise. 2.
DRIVE CONTROLS 4. THROTTLE PEDAL Controls the speed of the vehicle within the speed control setting selected. Pressing the pedal causes the machine to travel in the direction selected by the Directional Control Switch. To increase speed, increase pressure on the pedal. To decrease speed, decrease pressure on the pedal. 5. OPERATOR PRESENCE PEDAL - Prior to Serial Number (11*) This safety feature is designed to ensure that the operator has their left foot on pedal platform whenever machine is moving.
DRIVE CONTROLS 10. BATTERY DISCHARGE INDICATOR Indicates the charge level of the batteries. The meter display is divided into 10 vertical bars. Bars illuminated on the far right indicate full charge. Bars flashing near the left side indicate the batteries should be recharged. Further operation of the machine could damage the machine or the batteries. When the machine is left overnight with less than a full charge, the display may initially indicate a full charge.
SCRUB CONTROLS 2 3 1 4 1. Vacuum Shoe Lift Lever 2. Scrub Deck Actuator Switch 3-9 3. Solution Control Switch 4.
SCRUB CONTROLS 1. VACUUM SHOE Raises and lowers the vacuum shoes, and turns the vacuum motors on and off. To lower vacuum shoes and start vacuum motors, lift the lever from its raised position. To raise vacuum shoes and stop vacuum motors, lift the lever from its lowered position. 2. SCRUB DECK SWITCH Raises and lowers the scrub deck, turns the scrub brush motors on and off. To lower the scrub deck and turn on scrub brush motors, press the bottom of the switch.
MACHINE OPERATION PRE-RUN MACHINE INSPECTION Do a pre-run inspection to find possible problems that could cause poor performance or lost time from breakdown. Follow the same procedure each time to avoid missing steps. EMERGENCY STOP PROCEDURES 1. Release the throttle pedal by lifting right foot. NOTE: See maintenance section for pre-run machine inspection checklist items. 2. Turn machine power off with key switch by turning key switch counterclockwise. STARTING MACHINE 3.
MACHINE OPERATION FILLING SOLUTION TANK NORMAL SCRUBBING FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key. Plan the scrubbing pattern in advance. For efficient operation, the runs should be the longest possible without turning, stopping, or raising or lowering scrub deck. The longest track is around the perimeter of the area to be cleaned and a collapsing rectangle pattern is most efficient. 1. Turn the machine power off. 2.
MACHINE OPERATION TO BEGIN SCRUBBING PRIMING PUMP When operating the machine around people, pay close attention for unexpected movement. Use extra caution around children. If the solution system has gone dry or has been unused for a period of time, it may be necessary to follow the pump priming procedure. 1. Fill solution tank. 2. Loosen, but do not completely remove the strainer bowl. Solution should flow out of the strainer. If it does not, check the strainer screen inside the solution tank.
MACHINE OPERATION 2. Remove the recovery tank dome. Flush the recovery bag out with clean water. Do not use water hotter than 140°F (60°C) to clean tank. Damage may occur. 3. Clean debris from dome basket. 4. FOR SAFETY: Before leaving or servicing machine: stop on level surface, turn off machine and remove key. Clean off the float shut-off system and inspect for free movement of float. The float shut-off system is located in the rear of the recovery tank. 5.
NOTES: 3-15 86037880 CHARIOT EXTRACTOR 01/16/07
SERVICE SCHEDULE BEFORE EACH WORK PERIOD MAINTENANCE Check water level of batteries after charging; add distilled water if necessary. (Wet cell only) Check that dome and cover seal tightly. Visually check for damaged or worn tires. Check brushes for proper installation. Check vacuum hose connections. Check that vacuum shoes are securely attached. Check for securely attached drain hoses and caps. Check pedal(s), brake and steering for proper operation. Clean out recovery tank and dome basket.
MAINTENANCE- BATTERIES 3 4 5 6 1 2 1. Rear Cover Retainer Knob 2. Rear Cover 3. Battery Connector-Machine 4-2 4. Batteries 5. Battery Tray 6.
MAINTENANCE-BATTERIES When servicing machine, avoid contact with battery acid. BATTERIES The batteries provide the power to operate the machine. The batteries require regular maintenance to keep them operating at peak efficiency. The machine batteries will hold their charge for long periods of time, but they can only be charged a certain number of times. To get the greatest life from the batteries, charge them when their charge level reaches 25% of a full charge. Use a hydrometer to check the charge level.
MAINTENANCE-BATTERIES CHECKING BATTERY SPECIFIC GRAVITY CHARGING BATTERIES Use a hydrometer to check the battery specific gravity. When servicing machine, avoid contact with battery acid. Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging. Battery Check Wear eye protection and protective clothing when working with batteries. Charge batteries in a well ventilated area. CHECKING GRAVITY A. Hydrometer B.
MAINTENANCE-BATTERIES CHANGING BATTERIES 1. Replace the battery caps, and leave them in place while charging. Stop the machine in a clean area next to the charger. Turn off machine. 2. Unplug the battery connector from the machine. FOR SAFETY: When charging, connect the charger to the batteries before connecting the charger to the AC wall outlet. Never connect the charger to the AC wall outlet first. Hazardous sparks may result. 3. Plug the charger connector into the battery connector.
MAINTENANCE-VACUUM SHOES 2 1 3 1. Vacuum Shoes 2. Vacuum Shoes Glides 3.
MAINTENANCE - VACUUM SHOES VACUUM SHOES TO CLEAN VACUUM SHOES The dual offset vacuum shoes are designed to extract soiled solution from the carpet. The plastic vacuum shoe glides minimize damage to carpet and flooring. 1. With the vacuum shoes in the raised position, turn key switch “off”. MAINTENANCE 3. Flush vacuum shoes from top with water. If necessary, clean blockage from narrow opening with knife, scraper or similar device.
MAINTENANCE-SCRUB DECK 3 4 7 1. 2. 3. 4. 4-8 6 Hopper Hopper Retainer Plate Scrub Brush Motor Scrub Deck Lift Actuator 5 1 2 5. 6. 7. 8.
MAINTENANCE-SCRUB DECK SCRUB HEAD SCRUB BRUSH REPLACEMENT The dual cylindrical scrub head is designed to sweep and scrub the carpet. The brushes, turning in a counterclockwise rotation, pick up the debris and throw it into a removable hopper, and raise the pile of the carpet, giving it a lush groomed appearance. 1. Lift the drive side of the brush and push it onto drive hub until a positive stop is felt. The brush door cannot be installed until the brush is fully seated on the drive hub. 2.
MAINTENANCE-SCRUB DECK SCRUB DECK ADJUSTMENT ADJUSTMENT OF INDIVIDUAL BRUSHES Scrub deck adjustment consists of three types of adjustments. The first is to insure the individual brushes make the same width pattern end to end. Any tapered brush pattern should be adjusted out. The second is to make the pattern of equal width between front and rear brushes. Unequal patterns are caused by the scrub deck not being parallel to the floor. The third is to make the contact patterns on the floor the correct width.
MAINTENANCE-SCRUB DECK Do not use a pressure washer to clean around the brush motors. Use tap pressure only. BRUSH MOTOR CARBON BRUSH REPLACEMENT TO REPLACE SCRUB BRUSH MOTORS 1. Scribe alignment mark on motor barrel to motor cap. Remove two bolts. 1. With the scrub deck in the raised position, disconnect brush motor wiring connector from harness. 2. Remove end cap from motor. NOTE: Motors contain two wave washers in cap. Do not lose these. 2. Remove brushes and brush door. 3.
MAINTENANCE-SCRUB DECK SCRUB DECK ACTUATOR ADJUSTMENT ACTUATOR SCRUB DECK REMOVAL/REPLACEMENT FOR SAFETY: Before leaving or servicing machine, stop on a level surface. Turn off machine. 1. Lower scrub deck. 2. Disconnect spring assembly from actuator slide link. 3. Remove the clevis pin retaining the top of the actuator. 4. Remove slide link and actuator as an assembly by removing the two bolts connecting them to the deck through the bushings. 5.
MAINTENANCE–CIRCUIT PROTECTION CIRCUIT BREAKERS 1. CIRCUIT BREAKERS Circuit breakers interrupt the flow of power in the event of an electrical overload. When a circuit breaker is tripped, reset it by pressing the exposed button. If a circuit breaker continues to trip, the cause of the electrical overload should be found and corrected. 30 Amp. Protects the left vacuum motor circuit. 30 Amp. Protects the right vacuum motor circuit. 25 Amp. Protects the left scrub brush motor. 25 Amp.
MAINTENANCE-SOLUTION STRAINER & PUMP 1 2 6 1. Solution Strainer – Coarse 2. Solution Strainer – Fine 3. Pump 4-14 3 4 5 4. Solenoid Valve 5. Jets 6.
MAINTENANCE – SOLUTION STRAINER & PUMP 1. SOLUTION STRAINER – COARSE Located in bottom of tank. The coarse strainer protects the finer strainer from large debris. If the fine strainer is clean and the pump and solenoid valve are not working, then check the coarse strainer for debris. Drain the solution tank and clean the coarse strainer. To remove the strainer, rotate the strainer counterclockwise. Cleanout the debris from wire mesh and reassemble. 2.
MAINTENANCE-VACUUM & FLOAT SHUT-OFF 1 2 1. Recovery tank float shut-off 2.
MAINTENANCE – VACUUM & FLOAT SHUT-OFF RECOVERY TANK FLOAT SHUT-OFF When water is no longer being vacuumed from the floor and the vacuum fan is operating, the ball float has engaged. The vacuum motors will not vacuum water with recovery tank full. The recovery tank must be drained. FOR SAFETY: before leaving or servicing machine, stop on a level surface, turn off machine and disconnect power. TO REPAIR OR REPLACE VACUUM MOTORS 1. Remove rear cover from machine. 1.
MAINTENANCE- DRIVE MOTOR & BRAKE 1. 2.
MAINTENANCE-DRIVE MOTOR & BRAKE ELECTRIC PARKING BRAKE ENGAGEMENT To disengage brake: FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and remove key. Electric Brake Engagement This machine is equipped with an electric parking brake. The brake automatically engages and keeps the machine from moving whenever the operator steps off the platform or when emergency stop is engaged.
MAINTENANCE-DRIVE MOTOR & BRAKE DRIVE MOTOR CARBON BRUSH REPLACEMENT Do not use a pressure washer to clean around the motors. Use tap pressure only. FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and remove key. 7. Install new brush and reinstall connecting screw and lead. 8. When all new brushes are installed. Place all in retracted position, held into brush holder by spring tension. 9. Carefully replace brush cap. Reinstalling: 10.
MAINTENANCE-BAG REPLACEMENT REPLACING BAG REMOVING BAG 1. Install mandrel in bottom of bag. 1. Disconnect batteries and make sure parking brake is not overridden. 2. Place new bag in tank making sure hole for strainer basket is oriented properly. 2. Under left front side of machine loosen hose clamp on recovery dump hose. Do not remove hose. 3. Remove Dome and set aside 4. Remove Float cage, loosen screws that secure manifold assembly and remove manifold. 5.
MAINTENANCE-TRANSPORTATION PREPARATION FOR LOADING /UNLOADING TRAILER PUSHING MACHINE The machine may be pushed for short distances at speeds not to exceed 5 mph. Be careful to avoid damaging machine. The machine may be pushed by hand from the rear. NOTE: To avoid damage caused by regenerative voltage, disconnect traction motor before towing or pushing machine. MACHINE TIE-DOWNS Before loading or unloading machine from trailer, remove scrub brushes and vac shoes to eliminate interference with tie-downs.
MAINTENANCE-TROUBLESHOOTING PROBLEM No power to machine Little or no propel CAUSE Battery disconnected SOLUTION Check all battery cable connections Emergency shut-off activated Reset Battery cables corroded Faulty key switch Clean connections Replace switch Low battery charge Machine turned on with pedal not in neutral position Tripped circuit breaker Controller overheated Loose motor connection Charge batteries Allow pedal to return to neutral.
MACHINE TROUBLESHOOTING PROBLEM Vacuum motor(s) not running, or run slowly CAUSE Circuit breaker tripped SOLUTION Reset circuit breaker Faulty vacuum circuit or switch Check wires, connections and switch Worn vacuum motor brushes Replace brushes, check commutator Vacuum shoes will not go up/down Faulty cables or pulleys Repair/replace cables and pulleys Poor scrubbing performance Debris caught in scrub brushes Remove debris Worn brushes Replace brushes Low scrub brush down pressure Low batter
MACHINE TROUBLESHOOTINGCONTROLLER FAULT CODES PROPEL CIRCUIT BOARD TROUBLESHOOTING Curtis 1228 LED DIAGNOSTICS- Basic and Cylindrical During normal operation, with no faults present, the status LED is steadily on. If the controller detects a fault, the status LED provides two types of information. First, it displays a slow flash (2 Hz) or a fast flash (4 Hz) to indicate the severity of the fault. Slow-flash faults are self-clearing; as soon as the fault is corrected, the vehicle will operate normally.
MACHINE TROUBLESHOOTINGCONTROLLER FAULT CODES LED CODE 3,1 PROGRAMMER LCD DISPLAY PROC/WIRING FAULT EXPLANATION POSSIBLE CAUSE HPD fault present for >10 sec. 1. Misadjusted throttle. 2. Broken throttle pot or throttle mechanism. 3,2 BRAKE ON FAULT brake On fault 1. Electromagnetic brake driver shorted. 2. Electromagnetic brake coil open. 3,3 PRECHARGE FAULT precharge fault 1. Low battery voltage. 2. KSI and throttle turned on at same time. 3,4 BRAKE OFF FAULT brake Off fault 1.
PARTS 86037880 CHARIOT EXTRACTOR 01/16/07
BUMPER 1 2 6 7 10 9 3 6 10 7 11 5 8 1 4 5-1 86037880 CHARIOT EXTRACTOR 01/16/07
BUMPER REF 1 2 3 4 5 6 7 8 9 10 11 PART NO. 86276890 86007070 86063230 86063240 86071020 86270830 86010670 86070730 86197040 86279130 86251750 PRV NO. 70752 70849 140813 140814 140783 57023 87029 140729 57264 87083 67602 QTY 6 2 1 1 1 4 4 2 4 4 2 DESCRIPTION SCR, 5/16-18X3/4 PTHMS SS SCR, #12 X 1.
CONTROL PANEL- UPPER 4 3 5 2 1 6 1 2 8 9 3 10 18 16 17 18 11 16 13 12 15 19 13 14 7 13 13 5-3 86037880 CHARIOT EXTRACTOR 01/16/07
CONTROL PANEL - UPPER REF 1 2 3 4 5 6 PART NO. 86002010 86008900 86007130 86007140 86007180 86007190 PRV NO.
CONTROL PANEL- LOWER 1 13 2 14 3 4 5 13 11 10 7 8 12 6 5-5 9 86037880 CHARIOT EXTRACTOR 01/16/07 6
CONTROL PANEL-LOWER REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PART NO. 86223740 86273820 86277480 86070720 86008760 86005810 86075310 86271840 86006370 86010670 86279130 86271120 86005700 86027740 PRV NO. 70872 70019 70850 140728 80682 57245 61039 57285 67315 87029 87083 57125 57104 27911 QTY 6 2 3 1 1 8 1 3 3 6 6 6 8 1 DESCRIPTION SCR, 1/4-20 X .59 PPHMS SS C SCR, 1/4-20 X 1.
CONTROL PANEL HOUSING 2 3 3 1 6 5 11 10 4 7 9 8 5-7 86037880 CHARIOT EXTRACTOR 01/16/07
CONTROL PANEL HOUSING REF 1 2 3 4 5 6 7 8 9 10 11 PART NO. 86005810 86290540 86277480 86070710 86237900 86031730 86070700 86279750 86089650 86277420 86010630 PRV NO. 57245 70850 140726 35278 270084 140725 87252 78524 70841 87013 QTY 4 6 6 1 3 1 1 4 4 4 4 DESCRIPTION NUT, 1/4-20 HEX NYLOCK SS SCR, 10-32 X 1/2 TORX SS BLK NP SCR, 5/16-18 X1/2 PTHMS SS BRKT, LEFT CONSOLE MOUNT GASKET, .125 X .25W X 23L CONSOLE BRKT, RIHGT CONSOLE MOUNT WASHER, RET, PUSHNUT, 5/16 BOLT TUBE, 5/8 OD X .357 ID X 1.
DECAL 5 4 3 7 2 1 8 5-9 86037880 EXTRACTOR 01/06/09
DECAL REF 1 2 3 4 5 6 7 8 PART NO. 86004970 86244820 86244190 86243990 86244510 OPEN 86244830 86298970 PRV NO. 50990 501230 500882 500780 501108 QTY 1 1 1 1 1 501231 - 1 1 DESCRIPTION LABEL, WINDSOR LOGO DOMED DECAL, CHARIOT IEXTRACT LT LABEL, PANEL BASIC LEFT LABEL, COVER PANEL LABEL, PANEL, EXTRACTOR, RT SERIAL NO. FROM NOTES: DECAL, CHARIOT IEXTRACT RT LABEL, CLEAN BRUSHES AND DECK NOTE: See “SAFETY LABEL LOCATION” page for safety label information.
FRAME-LOWER 1 3 2 4 5 4 17 7 6 9 16 8 8 10 8 11 8 15 4 8 21 8 18 19 20 5-11 4 14 86037880 CHARIOT EXTRACTOR 01/16/07 4 13 12
FRAME-LOWER REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 PART NO. 86070750 86071130 86070760 86276070 86092500 86197040 86279130 86270830 86071120 86071430 86070740 86079320 86064300 86010670 86091420 86088760 86088750 86079290 86010630 86271870 86276950 PRV NO.
FRAME-UPPER 1 2 3 2 4 5 4 7 2 3 4 2 6 SEE VACUUM SHOE LIFT GROUP 4 5-13 86037880 CHARIOT EXTRACTOR 01/16/07
FRAME-UPPER REF 1 2 3 4 5 6 7 PART NO. 86091610 86270830 86010670 86276070 86083080 86277460 86073500 PRV NO. 140129 57023 87029 70593 66437 70847 270090 QTY 1 8 5 7 1 1 1 DESCRIPTION BRKT, HORIZ ELECT, EXTRACTOR NUT, 5/16-18 HEX NYLOCK SS WASHER, 5/16 FLAT SS SCR, 5/16 X 3/4 CARRIAGE SS PLATE, VERT BEARING SUPPORT SCR, 5/16-18 X 5/8 BSHCS SS BRKT, SIDE CHANNEL L 86037880 CHARIOT EXTRACTOR 01/16/07 SERIAL NO.
PEDAL PLATFORM-From Serial Number (11*) 21 18 8 16 19 9 17 25 2 1 22 15 30 6 14 3 4 24 10 22 5 29 15 12 26 28 13 11 23 27 20 7 5-15A 86037880 CHARIOT EXTRACTOR 03/31/10 11
PEDAL PLATFORM-From Serial Number (11*) REF PART NO. PRV NO.
PEDAL PLATFORM-To Serial Number (11*) 1 2 9 30 28 3 10 4 11 12 5 6 31 8 9 23 22 27 26 25 24 20 10 13 11 12 15 29 14 17 7 16 17 32 18 19 21 20 17 5-16A 86037880 CHARIOT EXTRACTOR 11/18/09
PEDAL PLATFORM-To Serial Number (11*) REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 PART NO. 86217650 86222700 86216380 86007110 86279720 86272040 86223580 86222520 86277390 86233170 86279730 86277380 86222510 86254970 86222780 86277360 86274340 86224360 86222810 86279140 86288720 86250280 86222790 86278060 86224350 86277370 86221850 86218810 86136310 86264920 86224750 86223260 PRV NO.
PEDAL PLATFORM 2 3 17 16 6 1 6 9 14 12 5 10 8 13 11 7 15 8 4 18 5 8 5 5 5-17 86037880 CHARIOT EXTRACTOR 01/16/07
PEDAL PLATFORM REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 PART NO. 86248920 86274690 86264920 86231070 86010670 86259430 86010770 86270830 86256470 86278850 86008680 86064480 86276980 86007780 86279630 86259440 86271190 86256130 PRV NO. 66487 70258 27049 730328 87029 87485 87143 57023 70852 80613 80607 629993 70775 73576 87212 87486 57142 730402 QTY 1 2 3 2 5 4 2 5 2 2 1 1 1 1 1 2 2 1 DESCRIPTION PIN, CLEVIS 1/2 X 2.25 SCR, 5/16-18 X 1.5 HHCS GR5PLT CABLE TIE, 7” UL/CSA BUMPER, 1 X 1.
REAR COVER 21 23 18 20 22 18 14 13 1 10 2 3 9 19 18 3 2 11 12 15 16 9 8 7 6 17 5 4 5-19 86037880 CHARIOT EXTRACTOR 04/16/09
REAR COVER REF PART NO. PRV NO.
SCRUB DECK 1 1 2 2 3 19 18 17 23 HOSE ROUTING 4 16 5 39 40 6 2 SEE DETAIL 'A' FROM PUMP OUTLET 9 37 38 34 8 43 7 10 11 12 13 32 36 33 34 24 25 14 15 42 41 35 20 2 1 42 31 27 30 26 28 FROM MAIN HARNESS 21 22 DETAIL 'A' 5-21 86037880 CHARIOT EXTRACTOR 09/13/08 21
SCRUB DECK REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 PART NO.
SCRUB DECK MOTORS 1 2 12 11 10 13 14 15 3 12 4 10 1 11 9 7 8 6 5 5-23 86037880 CHARIOT EXTRACTOR 01/16/07
SCRUB DECK MOTORS REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PART NO. 86277880 86222330 86279790 86137310 86217710 86219290 86219450 86223520 86228960 86279770 86279140 86277870 86219440 86279780 86004820 PRV NO. 70855 57504 87489 87098 29268 34418 41488 67598 09149 87487 87085 70854 41487 87488 48041 QTY 8 2 6 6 2 2 2 2 4 4 4 4 2 2 2 DESCRIPTION SCR, M8-1.25 X 35 LG SHCS SS NUT, M8 -1.
SCRUB DECK LIFT ACTUATOR 2 1 3 39 4 7 5 6 8 40 9 10 11 14 15 12 16 13 14 19 12 10 17 20 18 21 34 32 33 22 31 35 23 24 36 21 25 26 2 16 14 30 2 37 38 10 19 29 28 5-25 86037880 CHARIOT EXTRACTOR 05/11/07 27
SCRUB DECK LIFT ACTUATOR REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PART NO. 86011950 86248980 86006910 86090330 86278400 86066920 86273820 86070190 86276760 86010670 86228840 86259420 86091840 86005810 86231360 86010630 86277500 PRV NO.
SCRUB DECK LIFT LINKAGE 29 28 27 1 2 3 26 25 30 4 31 20 5 24 4 19 21 23 22 21 6 7 8 3 11 9 3 4 10 12 8 10 9 12 13 14 18 15 16 17 5 5-27 86037880 CHARIOT EXTRACTOR 02/10/07
SCRUB DECK LIFT LINKAGE REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PART NO. 86276070 86272380 86010770 86005630 86271530 86270830 86009400 86274660 86009050 86008460 86093180 86224370 86001320 86005830 86223540 86005800 86008810 PRV NO.
SOLUTION 2 1 42 1 2 4 12 5 2 11 10 3 9 6 TO TANK TO VALVE 13 37 7 8 16 FROM STRAINER 15 14 17 18 19 20 SEE DETAIL 'A' 21 32 TO SCRUB DECK 28 27 30 33 2 26 29 31 28 34 23 5 24 35 36 DETAIL ' B ' 2 25 TO TANK CLOSED 38 41 39 40 OPEN DETAIL ' B ' BOTTOM VIEW 5-29 86037880 CHARIOT EXTRACTOR 07/24/08 DETAIL 'A' 22
SOLUTION REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 PART NO. PRV NO. QTY DESCRIPTION 86197940 40027 2 HOSEBARB, 3/8MPT X 1/2 OD 90D DL 86233150 20042 5 CLAMP, 3/8 HOSE (D-SLOT) 86270990 57090 4 NUT, 10-32 HEX NYLOCK SS 86006100 65176 1 PUMP ASM, 36 V ACCESSORY 86010650 87018 6 WASHER, #10 X 6/16 OD 86070690 140724 1 BRKT, SOLUTION PUMP 86271820 57270 1 NUT, 5/16-18 CAPTIVE “J” PLTD 86274410 70195 4 SCR, 10-32 X 1.
STEERING 1 2 3 4 5 6 8 7 28 9 10 11 12 13 27 26 25 14 15 24 14 19 29 23 20 22 19 21 18 16 17 7 5-31 86037880 CHARIOT EXTRACTOR 01/16/07
STEERING REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 - PART NO. 86271610 86234810 86259610 86224050 86228790 86091740 86270830 86005610 86219600 86272900 86224060 86219650 86228670 86276070 86224800 86010670 86135970 86275190 86008610 86001030 86224320 86224810 86005630 86002750 86278940 86010780 86274330 86279130 86253200 86232780 PRV NO.
TANK 1 4 5 2 33 6 7 3 8 10 9 11 12 13 15 16 19 14 20 17 21 18 22 32 23 13 31 28 25 17 16 28 26 34 24 29 27 5-33 30 86037880 CHARIOT EXTRACTOR 12/12/08
TANK REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 PART NO. 86221900 86006470 86001510 86003710 86006480 86010630 86271940 86246080 86003350 86004010 86310180 86310190 86006860 86256100 86276840 86006760 86279630 86064920 86275800 86002620 86004000 86277560 86033570 86027800 86227120 86199840 86311740 PRV NO.
VACUUM 1 2 3 4 5 6 7 8 17 9 15 10 14 11 12 13 16 5-35 86067880 CHARIOT EXTRACTOR 01/16/07
VACUUM REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PART NO. 86236540 86238040 86236530 86090140 86082110 86064740 86078650 86274070 86237890 86237880 86005500 86083100 86083010 86270990 86270830 86083030 86270860 PRV NO. 34437 36243 34436 270139 62913 270100 36241 70086 35277 35276 53809 66439 66428 57090 57023 66430 57028 QTY 2 4 1 1 1 1 1 4 2 2 2 2 2 8 6 2 4 DESCRIPTION FOAM, POLY, 1/2 X 2 CURVED W/ADH GASKET, .25 T X .
VACUUM SHOES 1 2 4 3 5 6 7 9 16 8 14 13 12 11 10 5-37 86037880 CHARIOT EXTRACTOR 06/29/09 15
VACUUM SHOES REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PART NO. 86006580 86075450 86237910 86237920 86237930 86237940 86237950 86295390 86275950 86293190 86310740 86310750 86296410 86302700 86296550 86296350 PRV NO. 70085 27246 35279 35280 35281 35282 35283 70568 - QTY 10 1 1 1 1 1 1 1 4 3 1 1 1 10 1 1 DESCRIPTION SCR, 1/4-20 X 1/2 PPHMS SS COVER, VAC SHOE GASKET, VAC SHOE OUTER GASKET, 5.0 OD X 2.0 ID X .
VACUUM SHOES LIFT 1 2 6 1 3 5 8 16 7 8 14 9 8 13 10 17 15 5-39 86037880 CHARIOT EXTRACTOR 11/15/08 12
VACUUM SHOES LIFT REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PART NO. 86276690 86278330 86224370 86259420 86228840 86010670 86080420 86270830 86080410 86093700 OPEN 86219690 86276650 86310730 86276070 86259400 86295380 PRV NO. 70715 70641 730335 87232 09124 87029 62416 57023 62415 62424 48080 70707 70593 87205 - QTY 8 1 4 4 4 4 1 13 4 1 2 2 2 4 4 2 DESCRIPTION SCR, 5/16-18 X 1.75 CARR SS SHOULDER BOLT, 3/8OD X 3/8L SS SPACER, 1 OD X .391 ID X .500 WASHER, THRUST .51ID X 1 OD BEARING, FLANGED .
VACUUM SHOE LIFT HANDLE 1 2 3 6 26 4 7 12 8 11 9 5 10 12 11 18 14 24 15 12 12 17 19 16 13 17 13 11 17 14 12 27 20 21 23 13 11 22 24 11 12 25 5-41 12 86037880 CHARIOT EXTRACTOR 08/14/07
VACUUM SHOE LIFT HANDLE REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 PART NO. 86238360 86076610 86257120 86008650 86279450 86277490 86259420 86009560 86270920 86007020 86010670 86270830 86231150 86276760 86277460 86083440 86223370 86231570 86073600 86083500 86083490 86066130 86254280 86276070 86091820 86295860 86274720 PRV NO.
VACUUM HOSES 4 5 TO DOME 6 2 1 3 7 8 5-43 86037880 CHARIOT EXTRACTOR 01/24/09
VACUUM HOSES REF 1 2 3 4 5 6 7 8 PART NO. PRV NO. QTY DESCRIPTION 86240320 39729 1 HOSE ASM, 1.5 BLK VAC X 36 86177050 03-000176 3 CLAMP, HOSE #20 86320330 2 HOSE ASM, 1.5 BLK VAC X 12 86003010 27759 1 CUFF, HOSE 1.5” BLK A 2161 86264950 27746 2 CABLE TIE, .19 W X 11.5L BLK 86277460 70847 2 SCR, 5/16-18 X 5/8 BSHCS SS 86270830 57023 2 5/16 HEX NYLOCK SS 86093200 54212 1 MANIFOLD 86037880 CHARIOT EXTRACTOR 01/24/09 SERIAL NO.
WHEEL-FRONT DRIVE, GEAR 1 2 40 GEAR REPLACEMENT KIT 19 20 37 36 4 33 21 3 35 31 6 5 7 18 38 8 29 34 23 39 9 10 11 12 32 17A 17B 16 13 19 15 14 28 27 26 22 30 25 24 5-45 86037880 CHARIOT EXTRACTOR 10/21/11
WHEEL-FRONT DRIVE, GEAR REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17A 17B 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 PART NO. PRV NO. QTY DESCRIPTION 86275190 70377 4 SCR, 3/8-16 X 1.25 HHCS SS 86010790 87163 4 WASHER, 3/8 SPLIT LOCK PLTD 86002830 27196 1 CABLE TIE, .375 X 24.7 86006170 66031 1 PIN, ROLL 1/8” X 3/4”L 86264930 27050 1 CABLE TIE, 3.
WHEEL-REAR 1 2 3 5-47 86037880 CHARIOT EXTRACTOR 01/16/07
WHEEL-REAR REF 1 2 3 PART NO. 86259950 86008710 86232130 PRV NO. 89276 80623 17309 QTY DESCRIPTION 2 WHEEL, 10X2.5X.787ID BEARINGS 2 RING, ¾” EXT SNAP H-D 2 CAP, 2.75 ID X 1.0 L BLK VINYL 86037880 CHARIOT EXTRACTOR 01/16/07 SERIAL NO.
WIRING-BATTERIES 2 3 4 1 20A 20B 5 9 7 24 25 23 10 26 11 6 8 12 22 13 14 15 16 19 17 18 5-49 86037880 CHARIOT EXTRACTOR 08/14/07
WIRING-BATTERIES REF 1A 1B 2 3 4 5 6A 6B 7A 7B 8 9 10 11 12 13 14 PART NO. 86260200 86002510 86008920 86271910 86010670 86264960 86260610 86002570 86260230 86002580 86008760 86229700 86008300 86008410 86272810 86092910 86254990 PRV NO.
WIRING-COMPONENTS 2 1 3 4 6 4 5 7 8 9 10 11 13 12 5-51 86037880 CHARIOT EXTRACTOR 02/03/09
WIRING-COMPONENTS REF 1 2 3 4 5 6 7 8 9 10 11 12 13 PART NO. 86010780 86273830 86255910 86005710 86010630 86006850 86008920 86238500 86276070 86239720 86233410 86270830 86010670 PRV NO. 87162 70020 73659 57105 87013 70393 80889 81427 70593 41520 81270 57023 87029 QTY 2 2 2 4 2 2 2 1 1 1 1 1 1 DESCRIPTION WASHER, 1/4 SPLIT LOCK PLTD SCR, 1/4-20 X 1/2 HHCS SS NP STANDOFF, 1/4-20 X 1.0 HEX INS NUT, 1/4-20 HEX W/STAR WASHER WASHER, 1/4 ID X 5/8 OD SS SET SCR, 1/4-20 1.25L BOOT, RUBBER TERM.
WIRING-CONTROL PANEL 67 BLK 49 RED E F G 2 BLK 1 WHT 61 RED 1 73 RED 54 RED 3A 53 RED 30A 74 RED 20 RED 21 RED 25A 17 RED 25A 14 RED 16 RED 15 RED 30A 14 RED 30A 13 RED 3 LT BLU 70 LT BLU J 42 GRN 41 YLW 40 YLW 43 GRN 71 ORG 69 BLK 57 YLW 3A ACTUATOR SWITCH 7 BRN 8 BRN 79 BLK 34 BLK 31 RED WATER FLOW SWITCH 46 DK BLU 26 WHT-RED 56 RED K 45 GRY 37 WHT-YLW 62 YLW 50 RED 26 WHT/RED 33 BLK 51 RED 28 RED 4 RED 64 RED 65 WHT 12 RED 18 RED 85 GRN 35 LT BLU 79 RED 70 LT BL
WIRING-CONTROL PANEL REF 1 2 3 4 5 6 PART NO. 86261210 86239250 86010860 86260540 86261250 86311210 PRV NO. 29204 41559 880353 880426 29273 - QTY 4 1 1 1 1 1 DESCRIPTION DIODE ASM, 76008 X 76008 HARNESS, CNL PNL EXTRACTOR WIRE, 4X20 BK CTERM X5/16REING WIRE, 4X13 RD C.TERM X 5/16RING DIODE ASM, FAST RECOVERY LIGHT ASM, INDICATOR, CODE 86037880 CHARIOT EXTRACTOR 05/27/08 SERIAL NO.
WIRING-DRIVE MOTOR RED BLK 1 WHT 2 BLK 1 1 WHT 2 BLK WHT BLK CONTROL PANEL HARNESS 5-55 86037880 CHARIOT EXTRACTOR 01/16/07
WIRING-DRIVE MOTOR REF 1 PART NO. 86239120 PRV NO. 41522 QTY DESCRIPTION 1 HARNESS, CHARIOT PROPEL 86037880 CHARIOT EXTRACTOR 01/16/07 SERIAL NO.
WIRING-MAIN HARNESS 31 RED 32 BLK HORN DIAGRAM A 13 ORG 24 BLK 37 WHT/YLW 84 BLK 8 BRN 55 WHT/BLK 58 BLK 14 BLK BRAKE DRIVE MOTOR 6 WHT BLK 12 1 7 6 23 ORG 36 LT BLU 32 WHT 7 BRN 38 WHT-ORG 57 YLW BRN BRN 1 SOLENOID DIAGRAM B 10 BLK DECK SWITCH 21 WHT/ORG 16 BLK 22 WHT/BLK 15 YLW 11 RED 87 WHT/BLK RIGHT BRUSH MOTOR LEFT BRUSH MOTOR 86 BLK SCRUB LIFT ACTUATOR 10 BLK 11 RED 9 BLK 12 RED PUMP 2 DIAGRAM C 30 BLK 31 RED 26 BLK 1 18 LT BLU 3 17 WHT/YLW 3 4 6 23 RED 29 RED
WIRING-MAIN HARNESS REF 1 2 3 4 5 6 PART NO. 86239170 86239130 86260400 86239160 86239260 86260620 PRV NO. 41528 41523 880212 41527 41561 881000 QTY 1 1 REF 1 1 2 DESCRIPTION HARNESS, BRAKE HARNESS, MAIN WIRE ASM, REV POLARITY JUMPER HARNESS, DECK SWITCH HARNESS, EXTRACTOR LEVER WIRE, 2” BLK/16 76042 X 76042 86037880 CHARIOT EXTRACTOR 01/16/07 SERIAL NO.
WIRING-PEDAL PLATFORM-From Serial Number (11*) B A 1 8 BLU 9 RED DIAGRAM A DIAGRAM B ORG BRN GRN GRN BRN ORG LT BLU RED 5-59A 86037880 CHARIOT EXTRACTOR 11/18/09
WIRING-PEDAL PLATFORM-From Serial Number (11*) REF PART NO. PRV NO. QTY 1 86315100 - 1 DESCRIPTION SERIAL NO. FROM NOTES: HARNESS, PEDAL *SEE SERIAL NUMBER PAGE.
WIRING-PEDAL PLATFORM-To Serial Number (11*) B A 1 BRN BLU BRN RED DIAGRAM A DIAGRAM B ORG BRN GRN 5 GRN 1 2 3 7 BRN 4 5 6 ORG LT BLU RED 5-60A 86037880 CHARIOT EXTRACTOR 11/18/09
WIRING-PEDAL PLATFORM-To Serial Number (11*) REF 1 PART NO. 86218810 PRV NO. 23717 QTY DESCRIPTION 1 HARNESS, TWISTER PEDAL SERIAL NO. FROM NOTES: *SEE SERIAL NUMBER PAGE.
5-61 CURTIS 1228 MOTOR CONTROLLER 47 DK GRN BLK BRUSH RELAY 72 RED 73 RED 60 BLK 1 B+ 55 WHT-BLK 29204 18 RED VACUUM RELAY 29215 29204 52 RED MAIN RELAY WHT 86311210 28 RED STATUS LED 36V 86037880 CHARIOT EXTRACTOR 08/30/11 56 RED KEY SWITCH 4 RED RUN/RESET RELAY 64 RED 66 WHT 66 WHT 300K 61 RED 47 DK GRN BATTERY METER 40 YLW 42 GRN 41 YLW 43 GRN FORWARD/REV SWITCH 79 BLK 46 BLU 45 GRY 33 BLK 56 RED RESET SWITCH 49 RED 22 ORG 4 RED HORN SWITCH E-STOP 220K 23 ORG 43 GRN
DRAIN HOSE 86004310 PRV 39505 HOSE DIAGRAM TANK 12 MESH (COARSE) STAINER 86281940 PRV 39540 PUMP 86282360 PRV 39734 86282370 PRV 39735 100 MESH (FINE) STAINER 86281150 PRV 39282 VALVE 86281100 PRV 39274 86037880 CHARIOT EXTRACTOR 07/24/08 5-62
SUGGESTED SPARE PARTS PART NO. 86001910 86002000 86251410 86007140 86007190 86007240 86001740 86002730 86001730 86007130 86006370 86028890 86252980 86241730 5-63 PRV NO. 14606 14717 67506 72130 72161 72190 140816 270085 140804 72128 67315 84098 730369 44107 DESCRIPTION BREAKER, 30A 50VDC CIRCUIT BREAKER, 3 AMP RELAY, 15A 36V MINI SWITCH, SPST 2-POSITION ROCKER SWITCH KEY DPST SWITCH, SEALED PB ROUND BRAKE, 36 VDC W/CONNECTOR CHAIN, ISO 08B 12.
OPTIONS 86037880 CHARIOT EXTRACTOR 01/16/07
BACK-UP ALARM - OPTION 3 1 2 4 5-65 86037880 CHARIOT EXTRACTOR 01/16/07
BACK-UP ALARM - OPTION REF 1 2 3 4 PART NO. 86071140 86231500 86276780 86271840 PRV NO. 140817 80882 70728 57285 QTY 1 1 1 1 DESCRIPTION BRKT, BACK UP ALARM BUZZER, PIEZO 6-28VCD SCR, 5/16-18 X 3/4 HHCS SS NUT, 5/16-18 HEX NYLOCK THN SS 86037880 CHARIOT EXTRACTOR 01/16/07 SERIAL NO.
BATTERY CART - OPTION 27 26 28 3 30 5 24 3 8 9 29 25 2 6 1 2 15 3 4 3 23 3 22 5 10 5 3 3 6 9 8 7 13 12 5 3 14 20 11 21 19 16 15 18 17 5-67 31 3 86037880 CHARIOT EXTRACTOR 09/17/09 3
BATTERY CART - OPTION REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 PART NO. 86006930 86254290 86270830 86077010 86010670 86228840 86259410 86259400 86254890 86068490 86231090 86083120 86076600 86004070 86276790 86276690 86199430 86078890 86277130 86007020 86232590 86001350 86011020 86271840 86008130 86274730 86070790 86087340 86070800 86271870 86276070 PRV NO.
BATTERY CART - OPTION 1 2 4 5 3 7 7 5 6 10 3 6 17 3 8 9 10 11 12 13 14 15 6 10 10 3 3 16 5-69 86037880 CHARIOT EXTRACTOR 01/16/07
BATTERY CART - OPTION REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PART NO. PRV NO. 86078330 66478 86276070 70593 86270830 57023 86087800 730307 86228840 09124 86259410 87206 86006560 70083 86077140 51404 86226830 73268 86010670 87029 86244280 500934 86276060 70590 86254280 730331 86231150 09151 86259400 87205 86276690 70715 86077530 51403 QTY DESCRIPTION 1 PEDAL, BATTERY CART 2 SCR, 5/16-18 X 3/4 CARRIAGE SS 12 NUT, 5/16-18 HEX NYLOCK SS 2 STIFFENER, PEDAL, BATTERY CART 4 BEARING, FLANGED .314ID X .
SEAT - OPTION 2 13 14 1 12 11 3 4 5 6 10 9 8 7 15 16 17 18 19 20 23 24 22 21 5-71 86037880 CHARIOT EXTRACTOR 01/16/07
SEAT - OPTION REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 PART NO. PRV NO. QTY DESCRIPTION 86248390 730324 1 PAD, REAR REST 86082640 629995 1 PLATE, SEAT COVER 86276890 70752 4 SCR, 5/16-18 X 3/4 PTHMS SS 86279460 87164 2 WASHER, 1/2 SPLIT LOCK 86270710 01-000277 1 NUT, WING 3/8-16 86271930 57297 1 NUT, 3/8-16 HEX NYLOCK SS 86278910 87003 3 NUT, 3/8-16 HEX NYLOCK SS 86070830 140742 1 BRKT, LEFT REAR SEAT 86070840 140743 1 BRKT, RIGHT REAR SEAT 86277710 730347 1 SCR, 3/8-16 X 2.
WARNING LIGHTS - OPTION 1 6 2 3 3 4 FRONT 5 7 3 1 2 6 5-73 REAR 86037880 CHARIOT EXTRACTOR 01/16/07
WARNING LIGHTS - OPTION REF 1 2 3 4 5 6 7 PART NO. 86270990 86010650 86276820 86071490 86270990 86246200 86071500 PRV NO. 57090 87018 70740 140871 57090 51454 140872 QTY 4 4 4 1 2 2 1 DESCRIPTION NUT, 10-32 HEX NYLOCK SS WASHER, #10 X 6/16 OD SCR, 10-32 X 1/2 PTHMS BLK BRKT, UPPER WARNING LIGHT NUT, 10-32 HEX NYLOCK SS LED AMBER LIGHT, 12V BRKT, LOWER WARNING LIGHT 86037880 CHARIOT EXTRACTOR 01/16/07 SERIAL NO.
SERIAL NUMBERS REF. NO.
