iScrub Operating Instructions (ENG) MODELS: CSX24 10061090 CSX26SP 10061160 Read these instructions before using the machine 86317500-A 11/15/08
MACHINE DATA LOG/OVERVIEW OVERVIEW The Chariot Scrubber is a battery powered, stand-on, hard floor scrubber intended for commercial use. The appliance applies a cleaning solution onto a hard floor, scrubs the floor with brushes or pads, and then vacuums the soiled water back into the recovery tank.
TABLE OF CONTENTS Machine Data Log/Overview. ...............................2 Table Of Contents ................................................3 HOW TO USE THIS MANUAL How To Use This Manual.....................................1-1 SAFETY Important Safety Instructions ............................ 2-1 Hazard Intensity Level....................................... 2-2 Safety Label Location........................................ 2-3 OPERATIONS Technical Specifications....................................
HOW TO USE THIS MANUAL This manual contains the following sections: - HOW TO USE THIS MANUAL SAFETY OPERATIONS MAINTENANCE PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authorized Windsor dealers. When placing an order for parts, the machine model and machine serial number are important. Refer to the MACHINE DATA box which is filled out during the installation of your machine.
IMPORTANT SAFETY INSTRUCTIONS When using an battery powered appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Use only indoors. Do not use outdoors or expose to rain. Use only as described in this manual. Use only manufacturer’s recommended components and attachments.
HAZARD INTENSITY LEVEL The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
SAFETY LABEL LOCATION NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them. 86244300 PRV NO. 500955 WARNING LABEL 86252520 PRV NO.
TECHNICAL SPECIFICATIONS ITEM Nominal power Rated Voltage Rated Amperage Batteries Battery Compartment Dimensions Scrub Brush Motors - Disk Machine Scrub Brush Motors - Cylindrical Machine Vacuum Motor(s) Maximum flow rate of vacuum motor Maximum suction of vacuum motor Propelling Motor Mass (GVW) Weight empty without batteries Solution Control Solution capacity Recovery capacity Scrub brush diameter - Disk Machine Scrub brush diameter - Cylindrical Machine Scrub brush pressure Scrub brush speed - Disk Mach
TECHNICAL SPECIFICATIONS ITEM Height Length Width without squeegee Width of squeegee - Disk Machine Width of squeegee - Cylindrical Machine Width of scrub path - Disk Machine Width of scrub path - Cylindrical Machine MEASURE 50.6 inches (1285 mm) 52.5 inches (1330 mm) 26.5 inches (670 mm) 32.7 inches (830 mm) 37 inches (970 mm) 24 inches (610 mm) 26 inches (650 mm) LENGTH WIDTH HEIGHT SPECIAL NOTES: The sound pressure level at the operator’s ear was measured to be 68 dBA (Disk), 76dBA (cylindrical).
HOW THIS MACHINE WORKS The Chariot® is a battery powered, self-propelled, hard floor scrubber intended for commercial use. The appliance applies a cleaning solution onto a hard floor, scrubs the floor with brushes, and then vacuums the soiled water back into the recovery tank. The machine's primary systems are the solution system, scrub system, recovery system, and operator control system. The function of the solution system is to store cleaning solution and deliver it to the scrub system.
COMPONENTS 7 2 1 11 3 5 6 8 12 10 4 1. 2. 3. 4. 5. 6. Control Panel-Drive Control Panel-Scrub Control Housing Pedal Platform Rear Cover Tank 7. 8. 9. 10. 11. 12.
DRIVE CONTROLS 7 8 9 5 2 3 1 6 4 3-5 86317500 CHARIOT SCRUBBER 11/15/08
DRIVE CONTROLS 1. 2. 3. 4. 5. 1. Key Switch Emergency Stop/Brake Switch Directional Control / Drive Reset Switch Throttle Pedal Horn Button 6. 7. 8. 9. Steering Wheel Speed Control Battery Discharge Indicator Hour Meter KEY SWITCH Controls the power for machine functions. To turn the machine power on, rotate key clockwise. To turn the machine off, rotate key counterclockwise.
DRIVE CONTROLS 5. HORN BUTTON The horn is activated by pressing the horn button. 6. STEERING WHEEL The steering wheel turns the front wheel causing the machine to change direction. 7. SPEED CONTROL Controls the maximum speed of the machine. There are two transport settings, slow and fast. To change speed, rotate the dial to either slow or fast position. The slow position is to the left (counterclockwise), fast to the right (top position).
DRIVE CONTROLS 8. BATTERY CHARGE LEVEL INDICATOR Indicates the charge level of the batteries. The meter display is divided into 10 vertical bars. Bars illuminated on the far right indicate full charge. Bars flashing near the left side indicate the batteries should be recharged. Further operation of the machine could damage the machine or the batteries. When the machine is left overnight with less than a full charge, the display may initially indicate a full charge.
SCRUB CONTROLS A1 1 A2 A3 C B 1. FUNCTION MODE SWITCH The first two positions are for transport only. See drive controls section. A1 – Daytime cleaning/light cleaning This mode is used for light cleaning. In this mode the machine will propel at a maximum of medium speed. The scrub deck will automatically lower to a lower down pressure setting. The water will flow at a low rate. Water will automatically shut off in neutral and restart when pressure resumes.
SCRUB CONTROLS A3 – Heavy scrub level cleaning This mode is used for heavy level cleaning. In this mode the machine will propel at a maximum of slow speed. The scrub deck will lower to a heavy down pressure. The water will flow at a high rate. The vacuum will flow at a high rate. B – Vacuum only mode This mode is used for picking up solution only. The brushes and water will both be up and off. In this mode the machine will propel at a maximum of medium speed.
SCRUB CONTROLS-SQUEEGEE 1 2 1. Squeegee Deflection Adjustment Knobs 2.
SCRUB CONTROLS-SQUEEGEE 1. SQUEEGEE DEFLECTION ADJUSTMENT KNOBS (DISK SCRUBBER) 3. SQUEEGEE DEFLECTION ADJUSTMENT (CYLINDRICAL SCRUBBER) Adjusts the deflection along the entire length of the squeegee. Adjusts the deflection along the entire length of the squeegee. To increase squeegee blade deflection, turn the two knobs at the ends of the squeegee counterclockwise. To increase squeegee blade deflection, loosen the bolt at the wheel axle and raise in the slots.
MACHINE OPERATION PRE-RUN MACHINE INSPECTION EMERGENCY STOP PROCEDURES Do a pre-run inspection to find possible problems that could cause poor performance or lost time from breakdown. Follow the same procedure each time to avoid missing steps. 1. Push in emergency stop button. This will also engage the parking brake and cause the machine to stop immediately. NOTE: See maintenance section for pre-run machine inspection checklist items.
MACHINE OPERATION FILLING SOLUTION TANK NORMAL SCRUBBING FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key. Plan the scrubbing pattern in advance. The longest track is around the perimeter of the area to be cleaned. For efficient operation, the runs should be the longest possible without turning, stopping, or raising or lowering scrub deck/squeegee. 1. Turn the machine power off. 2. Remove solution cover. 3.
MACHINE OPERATION TO BEGIN SCRUBBING PRIMING PUMP When operating the machine around people, pay close attention for unexpected movement. Use extra caution around children. If the solution system has gone dry or has been unused for a period of time, it may be necessary to follow the pump priming procedure. Flammable liquids and/or reactive metals can cause explosions or fire! Do not pick up. 1. Fill solution tank. 1. Stand on the operator platform. Throttle pedal must be in neutral position. 2.
MACHINE OPERATION DOUBLE SCRUB TO STOP SCRUBBING 1. Rotate the function knob to either transport position. The brush motors will stop and the scrub deck will rise to the park position. After 10 seconds the squeegee will raise, and 10 seconds later the vacuum motor will turn off. This delay is to clear the vacuum hose of recovered solution. 2. Allow the throttle pedal to return to neutral. 3. Turn machine power off.
MACHINE OPERATION SOLUTION TANK RECOVERY TANK DOME 1. Remove the recovery tank dome. 2. Pull the solution drain hose from its mounting pocket. Unscrew the cap, then lower hose in direction of drain. RECOVERY DRAIN HOSE 3. Remove the solution tank lid. 4. Flush the solution tank out with clean water and run several gallons of clean water through systems. Do not use water hotter than 140°F (60°C) to clean tank. Damage may occur. NOTE: Never allow solution to remain in tank.
NOTES: 86317500 CHARIOT SCRUBBER 11/15/08 3-18
MAINTENANCE SERVICE SCHEDULE MAINTENANCE Check water level of batteries after charging; add distilled water if necessary. (Wet cell only) Check that dome and cover seal tightly. Visually check for damaged or worn tires. Check brushes or pads for proper installation. Check vacuum hose connections. Check that squeegee is securely attached and properly adjusted. Check for securely attached drain hoses, plug and cap. Check pedal, brake and steering for proper operation. Clean out recovery tank and dome basket.
MAINTENANCE-BATTERIES 1 2 3 4 6 5 1. 2. 3. Rear Cover Retainer Knob Rear Cover Battery Connector-Machine 4. 5. 6.
MAINTENANCE-BATTERIES When servicing machine, avoid contact with battery acid. BATTERIES (WET CELL ONLY) The batteries provide the power to operate the machine. The batteries require regular maintenance to keep them operating at peak efficiency. The machine batteries will hold their charge for long periods of time, but they can only be charged a certain number of times. To get the greatest life from the batteries, charge them when their charge level reaches 25% of a full charge.
MAINTENANCE-BATTERIES CHECKING BATTERY SPECIFIC GRAVITY CHARGING BATTERIES Use a hydrometer to check the battery specific gravity. When servicing machine, avoid contact with battery acid. Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging. Battery Check Wear eye protection and protective clothing when working with batteries. Charge batteries in a well ventilated area. CHECKING GRAVITY A. Hydrometer B.
MAINTENANCE-BATTERIES 5. Replace the battery caps, and leave them in place while charging. 6. Unplug the battery connector from the machine. FOR SAFETY: When charging, connect the charger to the batteries before connecting the charger to the AC wall outlet. Never connect the charger to the AC wall outlet first. Hazardous sparks may result. 7. Plug the charger connector into the battery connector. Connect the charger AC plug to a wall outlet.
MAINTENANCE-SQUEEGEE 4 5 6 1 2 1. 2. 3. 3 Squeegee Squeegee Deflection Adjustment Knobs Squeegee Level Indicator 4. 5. 6.
MAINTENANCE-SQUEEGEE SQUEEGEE BLADES TO REMOVE SQUEEGEE ASSEMBLY The front squeegee blade allows solution to pass through channels in the blade into the squeegee assembly while maintaining vacuum to provide lift. The front blade has four wear surfaces and can be rotated for extended life. The front blade should not require regular replacement under normal use. 1. With the squeegee in the up position, turn key switch “OFF”. The rear blade wipes the floor to a near dry condition.
MAINTENANCE-SQUEEGEE TO ADJUST SQUEEGEE PITCH 1. Choose a smooth, level surface. Turn “ON” the key switch. Lower the squeegee and drive forward at least 2 feet (60cm.). 2. With the squeegee down, stop the machine. Do not allow machine to roll back. FOR SAFETY: Before leaving or servicing the machine; stop on level surface, turn off machine and remove key. 3. Determine the differences, if any, in deflection of the squeegee blade between each end and the middle.
MAINTENANCE-SCRUB BRUSHES SCRUB BRUSHES FINISHED FLOORS There are four different types of brushes available to cover applications from cleaning heavily soiled floors to polishing. A pad driver is also available to take advantage of the many cleaning pads on the market. Please refer to the following to assist in selecting the proper brush or pad for the work at hand. Nylon bristles are used in a variety of applications on coated or uncoated surfaces.
MAINTENANCE-SCRUB DECK 4 3 1 2 5 6 1. Scrub deck Aqua-Mizer™ 2. Aqua-Mizer™ retainer knob 3. Scrub deck skirt 4. Scrub deck skirt stop 5. Scrub brush motor 6.
MAINTENANCE-SCRUB DECK Do not use a pressure washer to clean around the brush motors. Use tap pressure only. BRUSH MOTOR CARBON BRUSH REPLACEMENT TO REPLACE SCRUB BRUSH MOTORS 1. Scribe alignment mark on motor barrel to motor cap. Remove two bolts. 1. With the scrub deck in the raised position, disconnect brush motor wiring connector from harness. 2. Remove end cap from motor. NOTE: Motors contain two wave washers in cap. Do not lose these. 2.
MAINTENANCE-SCRUB DECK ACTUATOR SCRUB DECK REMOVAL/REPLACEMENT SCRUB DECK ACTUATOR ADJUSTMENT FOR SAFETY: Before leaving or servicing machine, stop on a level surface. Turn off machine. 1. Remove the two screws that secure actuator spring plate and pull actuator barrel from stud on actuator spring bracket. 2. Remove clevis pin from upper bracket of actuator. 3. Disconnect actuator from wiring harness. The actuator will need to be adjusted when replaced. To adjust the actuator: 1.
MAINTENANCE-CIRCUIT PROTECTION 1 1. CIRCUIT BREAKERS Circuit breakers interrupt the flow of power in the event of an electrical overload. When a circuit breaker is tripped, reset it by pressing the exposed button. If a circuit breaker continues to trip, the cause of the electrical overload should be found and corrected. 18 Amp. Protects the left scrub brush motor. 18 Amp. Protects the right scrub brush motor.
MAINTENANCE-SOLUTION STRAINER & PUMP-DISK 1 5 2 6 3 4 1. Solution Strainer-Coarse 2. Solution Strainer-Fine 3. Pump 4. Pump Mounting Plate 5. Solenoid Valve 6.
MAINTENANCE-SOLUTION STRAINER & PUMP-CYLINDRICAL 1 2 1. Solution Strainer-Coarse 2. Solution Strainer-Fine 3. Pump 4-15 4 6 3 5 4. Solenoid Valve 5. Jets 6.
MAINTENANCE-SOLUTION STRAINER & PUMP 1. SOLUTION STRAINER-COARSE Located in bottom of tank. The coarse strainer protects the finer strainer from large debris. If the fine strainer is clean and the pump and solenoid valve are not working, then check the coarse strainer for debris. Drain the solution tank and clean the coarse strainer. To remove the strainer, rotate the strainer counterclockwise. Cleanout the debris from wire mesh and reassemble. 2. 3.
MAINTENANCE-VACUUM & FLOAT SHUT-OFF 1 2 1. 2.
MAINTENANCE-VACUUM & FLOAT SHUT-OFF RECOVERY TANK FLOAT SHUT-OFF When water is no longer being vacuumed from the floor and the vacuum fan is operating, the ball float has engaged. The vacuum motor will not vacuum water with recovery tank full. The recovery tank must be drained. 1. The float shut-off screen can be cleaned in or out of the machine. 2. To clean the float shut-off while it is inside the machine wipe material off screen then rinse. Check that the ball is also clean and moves freely. 3. 4.
MAINTENANCE-DRIVE MOTOR & BRAKE 2 1 1. 2.
MAINTENANCE-DRIVE MOTOR & BRAKE ELECTRIC PARKING BRAKE ENGAGEMENT To disengage brake: FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and remove key. Electric Brake Engagement This machine is equipped with an electric parking brake. The brake automatically engages and keeps the machine from moving whenever the operator steps off the platform or when emergency stop is engaged.
MAINTENANCE-DRIVE MOTOR & BRAKE DRIVE MOTOR CARBON BRUSH REPLACEMENT 5. Install new brush and reinstall connecting screw and lead. Do not use a pressure washer to clean around the motors. Use tap pressure only. 6. When all new brushes are installed. Place all in retracted position, held into brush holder by spring tension. FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and remove key. 7. Carefully replace brush cap. Reinstalling: 10.
MAINTENANCE-BAG REPLACEMENT REMOVING OR REPLACING BAG 1. Disconnect batteries and make sure parking brake is not overridden. 2. Remove Dome and set aside. 3. Drain all solution from both sides of the bag and rinse well. 4. Remove float cage, loosen screw on elbow and remove elbow. (You can remove the bag by only removing the float cage and sliding the bag opening over the elbows.) 5. Remove threaded mandrel from the bottom of the bag. Turn counterclockwise, remove by grabbing the attached handle.
MAINTENANCE-BAG TRANSPORTING PUSHING MACHINE The machine may be pushed for short distances at speeds not to exceed 5 mph. Be careful to avoid damaging machine. The machine may be pushed by hand from the rear. NOTE: To avoid damage caused by regenerative voltage, disconnect traction motor before towing or pushing machine. MACHINE TIE-DOWNS There are two tie points located at front and each side of foot box frame and two at the front side of frame. Tie-down devices must be of the proper type and strength.
MAINTENANCE-TROUBLESHOOTING PROBLEM No power to machine Little or no propel CAUSE Battery disconnected SOLUTION Check all battery cable connections Emergency shut-off activated Reset Battery cables corroded Faulty key switch Clean connections Replace switch Low battery charge Charge batteries Machine turned on with pedal not in neutral position Tripped circuit breaker Wheels spin Controller overheated Loose motor connection Faulty drive reset circuit or switch Allow pedal to return to neutral.
MACHINE TROUBLESHOOTING PROBLEM Vacuum motor does not run, or runs slowly Squeegee will not go up/down Poor scrubbing performance Little or no solution flow to the floor Brush motors do not run, or run slowly Scrub deck goes down, then raises 4-25 CAUSE Faulty vacuum circuit or switch SOLUTION Check wires & connections Worn vacuum motor brushes Faulty circuit or actuator Replace brushes, check commutator Check wires, connectors and actuator Faulty cables or pulleys Repair/replace cables or pulley
MACHINE TROUBLESHOOTING- CONTROLLER FAULT CODES ERROR CODE DELUXE PROBLEM SOLUTION LOW BATTERY VOLTAGE THE BATTERY NEEDS CHARGING OR THERE IS A BAD CONNECTION TO THE BATTERY TRACTION MOTOR DISCONNECTED THE TRACTION MOTOR HAS A BAD CONNECTION, CHECK CONNECTIONS TO MOTOR BRUSH MOTOR DISCONNECTED THE BRUSH MOTOR HAS A BAD CONNECTION, CHECK CONNECTIONS TO MOTOR AUX FAULT CHECK AUX OUTPUT DEVICES, CHECK ALL ASSOCIATED WIRING TO AUX DEVICES VACUUM MOTOR DISCONNECTED THE VACUUM MOTOR HAS A BAD CONNECTI
NOTES: 4-27 86317500 CHARIOT SCRUBBER 11/15/08
PARTS 86317500 CHARIOT SCRUBBER 11/15/08
BUMPER 1 4 8 9 2 5 6 1 3 4 7 10 5-1 86317500 CHARIOT SCRUBBER 11/15/08
BUMPER REF 1 2 3 4 5 6 7 8 9 10 PART NO. 86270830 86197040 86276070 86276890 86010670 86279130 86070730 86315790 86314170 86314180 PRV NO. 57023 57264 70593 70752 87029 87083 140729 - QTY 4 4 2 6 4 4 2 1 1 1 DESCRIPTION SERIAL NO.
CONTROL PANEL 24 13 23 25 17 30 19A 19B 6 16 21 7 12 26 1 15 2 10 18 14 4 3 10 5 29 SUPPLED WITH CONTROLLER 28 11 27 22 20 9 5-3 8 86317500 CHARIOT SCRUBBER 11/15/08 SUPPLED WITH HARNESS
CONTROL PANEL PRV NO. QTY REF PART NO.
CONTROL PANEL HOUSING 2 3 5 3 1 6 11 4 7 10 5-5 9 8 86317500 CHARIOT SCRUBBER 11/15/08
CONTROL PANEL HOUSING REF 1 2 3 4 5 6 7 PART NO. 86005810 86290540 86277480 86317890 86237900 86031730 86317900 PRV NO. 57245 70850 35278 270084 - QTY 4 6 6 1 3 1 1 8 86279750 87252 4 9 10 11 86089650 86277420 86010630 78524 70841 87013 4 4 4 DESCRIPTION NUT, 1/4-20 HEX NYLOCK SS SCR, 10-32 X 1/2 TORX SS BLK NP SCR, 5/16-18 X1/2 PTHMS SS BRKT, LEFT CONSOLE MOUNT GASKET, .125 X .25W X 23L CONSOLE BRKT, RIGHT CONSOLE MOUNT WASHER, RET, PUSHNUT, 5/16 BOLT TUBE, 5/8 OD X .357 ID X 1.
DECAL 3 2 5 4 1 6 5-7 86317500 CHARIOT SCRUBBER 11/15/08
DECAL REF 1A 1B 2A PART NO. 86318570 86318590 86318580 PRV NO. - QTY 1 1 1 2B 3 4 5 6 86318600 86317040 86017030 86243990 86004970 500780 50990 1 1 1 1 1 DESCRIPTION LABEL, CHAR, ISCURB 24, LEFT LABEL, CHAR, ISCRUB 26C, LEFT LABEL, CHAR, ISCRUB 24, RIGHT LABEL, CHAR, ISCRUB 26C, RIGHT LABEL, PANEL, RIGHT LABEL, PANEL, LEFT LABEL, COVER PANEL LABEL, WINDSOR LOGO DOMED 86317500 CHARIOT SCRUBBER 11/15/08 SERIAL NO.
FRAME-LOWER 18 5 20 10 2 2 15 16A 16B 11 10 3 12 2 2 7 17 11 3 21 5 19 8 22 2 5 13 2 2 6 12 15 1 14 9 5-9 4 86317500 CHARIOT SCRUBBER 11/15/08
FRAME - LOWER REF PART NO. PRV NO.
FRAME-UPPER 2 3 4 2 3 5 6 2 2 7 1 2 5-11 86317500 CHARIOT SCRUBBER 11/15/08
FRAME-UPPER REF 1 2 3 4 5 6 7 PART NO. 86074160 86270830 86276070 86314760 86073500 86314770 86277460 PRV NO. 270101 57023 70593 270090 70847 QTY 1 10 12 1 1 2 1 DESCRIPTION BRKT, SIDE CHANNEL R NUT, 5-16-18 HEX NYLOCK SS SCR, 5-16-18 X 3/4 CARRIAGE SS TRAY, CABLE BRKT, SIDE CHANNEL L BRKT, STEERING SUPPORT SCR, 5/16-18 X 5/8 BSHCS SS 86317500 CHARIOT SCRUBBER 11/15/08 SERIAL NO.
PEDAL PLATFORM 21 18 8 16 19 9 17 25 2 1 22 15 6 14 3 4 24 10 22 15 5 12 26 28 13 11 23 27 20 7 5-13 86317500 CHARIOT SCRUBBER 11/15/08 11
PEDAL PLATFORM REF PART NO. PRV NO.
PEDAL PLATFORM 2 3 13 15 6 11 14 6 12 10 9 7 1 4 8 5 8 5 5-15 86317500 CHARIOT SCRUBBER 11/15/08
PEDAL PLATFORM REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PART NO. 86008680 86274690 86264920 86231070 86010670 86259430 86010770 86270830 86256470 86278850 86248920 86064480 86271190 86007780 86259440 PRV NO. 80607 70258 27049 730328 87029 87485 87143 57023 70852 80613 66487 629993 57142 73576 87486 QTY 1 2 3 2 5 4 2 4 2 2 1 1 2 1 2 DESCRIPTION COTTER, 1/2” RING SCR, 5/16-18 X 1.5 HHCS GR5PLT CABLE TIE, 7” UL/CSA BUMPER, 1 X 1.375 RUBBER WASHER, 5/16 FLAT SS M12 FLAT WASHER WASHER, 7/16ID X1D.
REAR COVER 11 12 9 10 14 13 1 2 3 9 8 3 2 15 16 7 6 5-17 4 5 86317500 CHARIOT SCRUBBER 11/15/08
REAR COVER REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PART NO. 86276780 86279130 86010670 86031780 86005860 86228980 86275870 86242140 86010770 86248380 86005630 86071030 86010780 86271940 86006560 86066940 PRV NO. 70728 87083 87029 270082 57273 09152 70556 72193 87143 66433 57022 140786 87162 57299 70083 140891 QTY 3 5 5 1 2 2 2 1 2 1 1 1 2 2 2 1 DESCRIPTION SCR, 5/16-18 X 3/4 HHCS SS WASHER, 5/16 SPLIT LOCK PLTD WASHER, 5/16 FLAT SS COVER, REAR, DELUXE NUT, 1/4-20 X 12MM HEX BARREL BEARING FLANGED .
SCRUB BRUSH/PAD DRIVER-DISK 7 5 6 9 4 8 7 5 6 9 4 8 1 5 3 5-19 86317500 CHARIOT SCRUBBER 11/15/08 2A 2B 2C 2D
SCRUB BRUSH/PAD DRIVER-DISK REF 1 2A 2B 2C 2D 3 4 5 6 7 8 9 PART NO. 86000170 86000180 86000190 86000200 86283820 86005070 86276590 86276580 86276600 86007910 86007280 86005940 PRV NO.
SCRUB BRUSH/PAD-CYLINDRICAL 5-21 86317500 CHARIOT SCRUBBER 11/15/08
SCRUB BRUSH/PAD-CYLINDRICAL REF 1 2 3 4 5 6A 6B 6C 6D 7A 7B 7C 7D 7E 8 PART NO. 41150040 74010050 51128230 50052670 73430370 63693890 63694540 63694550 63694560 69069350 69069810 69069820 69069830 69069840 47624320 PRV NO.
SCRUB DECK – DISK 20 19 19 1 20 2 8 18 3 FROM PUMP 4 8 17 5 16 15 8 9 14 10 11 12 13 5-23 86317500 CHARIOT SCRUBBER 11/15/08 6 7
SCRUB DECK-DISK REF PART NO. PRV NO.
SCRUB DECK-CYLINDRICAL 5-25 86217500 CHARIOT SCRUBBER 11/15/08
SCRUB DECK-CYLINDRICAL SERIAL NO. FROM REF PART NO. PRV NO.
SCRUB DECK MOUNTING-CYLINDRICAL 1 2 8 3 4 5 6 7 9 5-27 86217500 CHARIOT SCRUBBER 11/15/08
SCRUB DECK MOUNTING-CYLINDRICAL REF 1 2 3 4 5 6 7 8 9 PART NO. 86315230 86274660 86224370 86008460 86009050 86010770 86005630 86314850 86314840 PRV NO. 70255 730335 80102 81324 87143 57022 - QTY 1 2 2 2 2 2 2 1 1 DESCRIPTION PIN, BALL LOCK SCR, 3/8-16 X 1.5 HHCS GR5 PLT SPACER, 1 OD X .391 ID X .500 SPACER, .500OD X .391ID X .400 BEARING, 1/2 ID X 11/32L NYLON WASHER, #6 LOCK NUT, 3/8-16 HEX NYLOCK THIN SS ARM ASSY, DECK, RIGHT ARM ASSY, DECK, LEFT 86317500 CHARIOT SCRUBBER 11/15/08 SERIAL NO.
SCRUB DECK LIFT-DISK 10 SEE DETAIL 'A' 6 13 11 14 9 12 15 16 7 5 17 4 18 3 29 19 22 16 19 23 21 20 28 24 27 26 1 21 19 2 22 20 16 8 25 5-29 86317500 CHARIOT SCRUBBER 11/15/08 DETAIL 'A'
SCRUB DECK LIFT-DISK REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 PART NO. 86276920 86008810 86273850 86010780 86079030 86091760 86274110 86005830 86008660 86277030 86224370 86270830 86272460 86011950 86275510 86010770 86070810 86255450 86005630 86271530 86009050 86008460 86224380 86274010 86001320 86077330 86223540 86005800 86005810 PRV NO.
SCRUB DECK ACTUATOR-CYLINDRICAL 16 19 18 17 16 23 19 18 17 14 23 2 9 28 17 17 20 26 26 10 13 21 12 5 22 17 3 4 28 1 27 28 11 18 6 1 17 8 27 18 25 5-31 7 2 21 86317500 CHARIOT SCRUBBER 11/15/08 15 24
SCRUB DECK ACTUATOR-CYLINDRICAL REF PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 86317340 86317330 86316550 86315290 86315260 86315250 86315240 86270770 86315150 86315140 86315120 86315110 86315090 86314810 86273740 86224380 86010780 86010670 86231090 86006980 86136850 86274460 86273920 86273820 86273780 86273750 86005810 86270990 PRV NO.
SCRUB DECK SKIRTS-DISK 1 2 3 6 4 5 20 5 21 7 8 9 24 10 19 11 18 12 5 23 22 17 16 15 7 14 13 5-33 86317500 CHARIOT SCRUBBER 11/15/08
SCRUB DECK SKIRTS-DISK REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 PART NO. 86270830 86070960 86276070 86228900 86005810 86276330 86276950 86277410 86271950 86079130 86007650 86007070 86066460 86001560 86091770 86001700 86066480 86091780 86001570 86066470 86277500 86271870 86026470 86026460 PRV NO.
SCRUB DECK AQUA-MIZER™ 16 15 1 14 2 13 17 4 5A 5B 3 6 7 8 9 3 12 11A 11B 10 18 9 5-35 86317500 CHARIOT SCRUBBER 11/15/08
SCRUB DECK AQUA-MIZER™ REF PART NO. PRV NO. QTY 1 2 3 4 5A 5B 6 7 8 9 10 11A 11B 12 13 14 15 16 17 18 86270830 86277050 86276950 86066430 86001540 86283550 86071000 86219690 86277230 86005810 86070990 86001520 86283560 86066420 86272540 86091800 86008670 86091790 86024990 86025000 57023 70782 70772 140747 140753 140939 140779 48080 70815 57245 140778 140752 140940 140746 66465 140776 80606 140774 47456 47457 4 2 9 1 1 1 1 2 2 9 1 1 1 1 2 1 2 1 - DESCRIPTION SERIAL NO.
SOLUTION-DISK 28 5 7 12 TO SOLENOID 28 5 8 34 6 23 24 19 9 22 11 TO TANK 5 21 10 25 1 30 3 29 32 33 26 27 5 20 13 18 14 5 15 16 4 20 5-37 17 86317500 CHARIOT SCRUBBER 11/15/08 2 31
SOLUTION-DISK REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 PART NO. 86248010 86226950 86073960 86235450 86233150 86270990 86281940 86198050 86240390 86282190 86247760 86240600 86197540 86225680 86197420 86001590 86007940 86005870 86136800 86281950 86315510 86264920 86274410 86070690 86010650 86006100 86271820 86279130 86276780 86197940 86246090 86254320 86259450 86252730 86233110 86233300 PRV NO.
SOLUTION-CYLINDRICAL 5 28 7 28 6 TO 24 SOLENOID 23 5 22 21 25 12 8 9 1 33 11 TO TANK 19 5 34 36 35 18 5 20 10 38 37 2 4 30 29 27 32 17 13 3 5 14 15 5-39 16 86317500 CHARIOT SCRUBBER 11/15/08 26 31
SOLUTION-CYLINDRICAL REF PART NO. PRV NO.
SQUEEGEE-DISK 1 39 2 38 37 3 9 40 4 36 5 8 35 5 6 7 6 34 8 5 33 9 11 7 10 11 15 12 13 14 15 16 17 18 19A 19B 20 32 30 21 29 22 25 23 24 26 31 28 5-41 27A 27B 86317500 CHARIOT SCRUBBER 11/15/08
SQUEEGEE-DISK REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19A 19B 20 21 22 23 24 25 26 27A 27B 28 29 30 31 32 33 34 35 36 37 38 39 40 PART NO.
SQUEEGEE-CYLINDRICAL 5-43 86317500 CHARIOT SCRUBBER 11/15/08
SQUEEGEE-CYLINDRICAL REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PART NO. 73120040 63212110 50942310 55152670 86137310 86274860 50319890 86005630 50319910 73114220 73120260 50443040 73120580 73030370 64354010 51052450 PRV NO.
SQUEEGEE LIFT-DISK 1 2 15 3 10 20 25 5 13 13 13 2 10 10 6 11 12 8 15 9 7 26 16 14 27 16 22 17 17 18 13 19 21 16 23 10 24 16 4 17 13 20 5-45 86317500 CHARIOT SCRUBBER 11/15/08
SQUEEGEE LIFT-DISK REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 PART NO. 86068190 86273820 86000870 86083490 86068230 86270870 86002780 86277410 86075430 86270830 86276070 86277400 86010670 86277460 86271870 86223370 86231150 86083440 86276760 86274720 86071300 86224290 86071310 86083500 86271840 86228880 86277480 PRV NO.
SQUEEGEE LIFT-CYLINDRICAL 5-47 86317500 CHARIOT SCRUBBER 11/15/08
SQUEEGEE LIFT-CYLINDRICAL REF PART NO. PRV NO.
SQUEEGEE SWING 1 1 24 23 22 21 2 20 3 4 6 19 18 25 5 6 16 15 17 6 7 14 7 13 6 12 11 10 6 9 8 5-49 86317500 CHARIOT SCRUBBER 11/15/08
SQUEEGEE SWING REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 PART NO. 86276690 86091530 86090300 86083370 86091540 86270830 86271530 86008810 86271980 86223590 86001320 86091810 86224290 86083400 86276760 86272630 86008650 86228840 86277030 86224380 86083150 86083310 86226030 86222580 86070820 PRV NO.
STEERING 1 2 3 5 6 8 7 4 28 9 10 11 12 13 27 26 25 15 24 14 19 29 23 22 21 20 19 18 16 17 30 5-51 86317500 CHARIOT SCRUBBER 11/15/08
STEERING REF PART NO. PRV NO.
TANK 5-53 86317500 CHARIOT SCRUBBER 11/15/08
TANK REF PART NO. PRV NO.
VACUUM 7 2 6 4 9 3 10 11 1 8 7 5-55 5 86317500 CHARIOT SCRUBBER 11/15/08
VACUUM REF PART NO. PRV NO. QTY DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 86314790 86314780 86012210 86279630 86010630 86006760 86005710 86270830 86237440 86318080 86264950 87212 87013 70305 57105 57023 35168 27746 3 1 1 1 3 1 6 2 1 1 2 ISOLATOR, RUBBER, 1/4-20 UNC M PLATE, VAC MOTOR VAC MOTOR, 36VDC 2ST TD WASHER, .344IDX1.130ODX.09T PLT WASHER, 1/4 X 5/8 FLAT SS SCR, 5/16-18 X 3/4 HHCS GR5 NUT, 1/4-20 HEX W/STAR NUT, 5/16-18 HEX NYLOCK SS GASKET, 4.06 X 2.50 X .38 MUFFLER ASSY, 1.5 HOSE CABLE TIE, .
WHEEL-FRONT DRIVE 2 1 19 20 21 3 6 4 7 18 8 29 23 9 10 11 12 5 16 13 19 15 14 28 27 26 22 30 25 24 5-57 86317500 CHARIOT SCRUBBER 11/15/08 17A 17B
WHEEL-FRONT DRIVE REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17A 17B 18 19 20 21 22 23 24 25 26 27 28 29 30 - PART NO. PRV NO.
WHEEL-REAR 1A 1B 2 3 5-59 86317500 CHARIOT SCRUBBER 11/15/08
WHEEL-REAR REF 1A 1B 2 3 PART NO. 86011110 86259930 86008710 86232130 PRV NO. 89261 89274 80623 17309 QTY 2 2 2 DESCRIPTION WHEEL, 10X2.5X.787ID BEARINGS WHEEL, 10X2.5, W/BEARINGS, GRY RING, ¾” EXT SNAP H-D CAP, 2.75 ID X 1.0 L BLK VINYL SERIAL NO.
WIRING-BATTERIES 2 3 4 1A 1B 20A 20B 20C 5 9 24 25 23 7A 7B 6A 6B 10 11 26 8 12 22 13 14 15 16 19 17 18 5-61 86317500 CHARIOT SCRUBBER 11/15/08
WIRING-BATTERIES REF 1A 1B 2 3 4 5 6A 6B 7A 7B 8 9 10 11 12 13 14 15 16 17 18 19 20A 20B 20C 21A 21B 22 23 24 25 26 PART NO. 86260200 86002510 86008920 86271910 86010670 86264960 86260610 86002570 86260230 86002580 86008760 86229700 86008300 86008410 86272810 86092910 86254990 86278150 86259910 86088790 86276070 86270830 86228410 86283410 86228430 86284090 86000150 86005810 86233360 86273980 86010650 86270890 PRV NO.
WIRING-COMPONENTS 1 2 3 4 5 6 6 5-63 86317500 CHARIOT SCRUBBER 11/15/08
WIRING-COMPONENTS REF 1 2 3 4 PART NO. 86008920 86270830 86229770 86273980 PRV NO. 80889 57023 140805 70066 QTY 2 2 1 2 5 86238500 81427 1 6 86239720 41520 1 DESCRIPTION BOOT, RUBBER TERM. ISOLATOR NUT, 5/16-18 HEX NYLOCK SS BLOCK, SHUNT MOUNT SCR, 10-32 X 3/4 PPHMS GROMMET, 1.703 ID X 2.5 OD X .125 GRV HORN, 108 DB MINATURE W/RING 86317500 CHARIOT SCRUBBER 11/15/08 SERIAL NO.
BRUSH L B C 30-GRY 69-RED 65-WHT 67-GRN 62-WHT 38-YEL 31-BLK 32-GRY PROPEL 19-PUR HORN HORN PF PF POT POT WIPE B-SW B-SW CHRG TB 13-BRN 14-BLU 15-WHT 16-YEL 17-GRN 18-ORG 3- BLU 4- BLU AUX3 AUX3 AUX2 AUX2 AUX1 AUX1 BRAKE BRAKE 73-BLU L-BRUSH 66-YEL TB1 1 64-BLU R-BRUSH 72-BRN 7 LOAD C A 70,71-BLK 1 LINE PIN 1 - 22-BRN PIN 2 - 23-BLU PIN 3 - 24-WHT PIN 4 - 25-YEL PIN 5 - 26-GRN PIN 6 - 27-ORG PIN 7 - 28-VIO PIN C - 29-PNK BRUSH R FROM C VACUUM WIRING-CONTROL PANEL SW1 63-BRN
WIRING-CONTROL PANEL REF 1 2 3 PART NO. 86313700 86010860 86010850 PRV NO. 880353 880352 QTY 1 1 1 DESCRIPTION HARNESS, PANEL 2 STAGE WIRE, 4X20 BK CTERM C5/16RING WIRE, 4X2ORD CTERM C3/8RING 86317500 CHARIOT SCRUBBER 11/15/08 SERIAL NO.
WIRING-DISK / +Ubatt AUXsupplyPIN1 19/VIO KSI-18 -ESTOP 63/BRN 61/WHT OPTIONAL -KSI OPTIONAL 72/BRN 45/BRN -PLATFORM 60/WHT 46/BRN -K2 -FLASHER -K1. -K1 -K2 -K2.
WIRING-DISK B+ CONNECTOR C -F1.
WIRING-DISK +Ubatt / B+ -U4 CONNECTOR B AUX1 -X12 -X14 -X11 -X4 AUX2 -X10 -X3 AUX4 AUX3 -X8 -X9 -X1 B- -X2 -18A -BRUSHR M -18A -BRUSHL M M M -DECK -SQUEGEE -SOLUTION M M M -VACUUM -TRACTION -BRAKE -WATER TRACTION/SOLENOID 24V FOR RELAYS / 5-69 86317500 CHARIOT SCRUBBER 11/15/08
WIRING-CYLINDRICAL +Ubatt / AUXsupplyPIN1 KSI-18 -ESTOP OPTIONAL -KSI OPTIONAL -PLATFORM -FLASHER -K1. -K2 -K2.
WIRING-CYLINDRICAL B+ CONNECTOR C -F1.
WIRING-CYLINDRICAL +Ubatt / B+ -U4 CONNECTOR B AUX1 -X12 -X14 -X11 -X4 AUX2 -X10 -X3 AUX4 AUX3 -X8 -X9 -X1 B- -X2 -18A -BRUSHR M -18A -BRUSHL M M M -DECK -SQUEGEE -SOLUTION M M -VACUUM -TRACTION M -BRAKE 24V FOR RELAYS -WATER -GND / 86317500 CHARIOT SCRUBBER 11/15/08 5-72
WIRING-DRIVE MOTOR RED BLK 1 WHT 2 BLK 1 2 BLK 1 WHT 2 BLK WHT BLK CONTROL PANEL HARNESS 5-73 86317500 CHARIOT SCRUBBER 11/15/08
WIRING-DRIVE MOTOR REF PART NO. PRV NO. QTY 1 86239120 41522 1 DESCRIPTION SERIAL NO.
WIRING-MAIN HARNESS DIAGRAM A HORN 13 ORG TB2 TB1 14 BLK 19 WHT BRAKE 2 13-BRN 14-BLU 15-WHT 16-YEL 17-GRN 18-ORG 3- BLU 4- BLU 20 BLK DRIVE MOTOR 6 BRN 6 BRN SOLENOID VALVE 15-YEL 16-BLK 21-WHT/ORG 22-WHT/BLK 17-WHT/YEL 18-BLU 19-WHT 20-BLK 14-BLK 13-ORG BLU RED GRN ORG BRN 6-BRN 6B-BRN OPEN 67-GRN 73-BLU 60-WHT - K1 72-BRN 33-PNK - C 39A-GRN - C 58-BRN - K1 59-BLU - K1 34-VIO - C 39C-ORG - C 10 BLK LEFT BRUSH MOTOR 16 BLK 15 YLW 11 RED PANEL HARNESS RIGHT BRUSH MOTOR 3 FROM MAIN HA
WIRING-MAIN HARNESS REF PART NO. PRV NO. QTY 1 2 3 4 86313710 86318640 86318650 86318660 - 1 1 1 1 5 86319780 - 1 DESCRIPTION HARNESS, MAIN HARNESS, PUMP JUMPER HARNESS, BRUSH MOTOR HARNESS BRUSH ACTUATOR HARNESS, WARNING LIGHTS OPTION 86317500 CHARIOT SCRUBBER 11/15/08 SERIAL NO.
WIRING-PEDAL PLATFORM A 8 BLU 9 RED DIAGRAM A 5 GRN 7 BRN 6 ORG 5-77 86317500 CHARIOT SCRUBBER 11/15/08
WIRING-PEDAL PLATFORM REF PART NO. PRV NO. QTY 1 86315100 - 1 DESCRIPTION SERIAL NO.
86282190 (13") PRV 39616 DRAIN HOSE 86315510 HOSE DIAGRAM-DISK TANK SHUT-OFF VALVE 86281950 (32") PRV 39541 STRAINER (FINE) SOLENOID VALVE 86281100 (8") PRV 39274 86281310 (8") PRV 39326 86281310 (8") PRV 39326 86281940 (40") PRV 39540 PUMP STRAINER (COARSE) SCRUB DECK 5-79 86317500 CHARIOT SCRUBBER 11/15/08
86315510 DRAIN HOSE HOSE DIAGRAM-CYLINDRICAL SHUT-OFF VALVE STRAINER (FINE) 86281950 (32) PRV 39541 PUMP STARINER (COARSE) 86281940 (40") PRV 39540 86282360 (28") PRV 39734 TANK SOLENOID VALVE 63908920 QUICK DISCONNECT 86317500 CHARIOT SCRUBBER 11/15/08 5-80
SUGGESTED SPARE PARTS PART NO. 86316160 86008900 86004440 86199840 86317770 86305960 86004860 86004890 86314050 86313900 86007170 86007190 86313820 86009200 86312800 86001520 86001540 86001560 86001570 86001580 86001630 86001700 86001740 86231560 86002780 86007940 86256120 86292590 86314150 86295200 86064300 86242140 86071030 86010600 86237440 5-81 PRV NO.
OPTIONS
BATTERY CART - OPTION 27 26 28 3 30 5 24 3 8 9 29 25 2 6 1 2 15 3 4 3 23 3 22 5 10 5 3 3 6 9 8 7 3 11 20 14 8 21 19 16 15 18 17 6-1 13 12 5 16 3 86317500 CHARIOT SCRUBBER 11/15/08 3
BATTERY CART - OPTION REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 PART NO. 86006930 86254290 86270830 86077010 86010670 86228840 86259410 86259400 86254890 86068490 86254280 86083120 86076600 86004070 86276790 86276690 86199430 86078890 86277130 86136730 86232590 86001350 86011020 86271840 86008130 86274730 86070790 86087340 86070800 86271870 PRV NO.
BATTERY CART - OPTION 1 2 4 5 3 7 7 5 6 10 3 6 17 3 8 9 10 11 12 13 14 15 6 10 10 3 3 16 6-3 86317500 CHARIOT SCRUBBER 11/15/08
BATTERY CART - OPTION REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PART NO. 86078330 86276070 86270830 86087800 86228840 86259410 86006560 86077140 86226830 86010670 86244280 86276060 86254280 86231150 86259400 86276690 86077530 PRV NO.
SEAT - OPTION 2 13 14 1 12 11 3 4 5 6 10 9 8 7 15 16 17 18 19 20 23 24 22 21 6-5 86317500 CHARIOT SCRUBBER 11/15/08
SEAT - OPTION REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 PART NO. 86248390 86082640 86276890 86279460 86270710 86271930 86278910 86070830 86070840 86277710 86008650 86246320 86272300 86251860 86279620 86276070 86277510 86009200 86254300 86094000 86276710 86093790 86010670 86270830 PRV NO.
WARNING LIGHTS - OPTION 1 6 2 3 3 4 FRONT 5 7 3 1 2 6 6-7 REAR 86317500 CHARIOT SCRUBBER 11/15/08
WARNING LIGHTS - OPTION REF 1 2 3 4 5 6 7 PART NO. 86270990 86010650 86276820 86071490 86270990 86246200 86071500 PRV NO. 57090 87018 70740 140871 57090 51454 140872 QTY 4 4 4 1 2 2 1 DESCRIPTION NUT, 10-32 HEX NYLOCK SS WASHER, #10 X 6/16 OD SCR, 10-32 X 1/2 PTHMS BLK BRKT, UPPER WARNING LIGHT NUT, 10-32 HEX NYLOCK SS LED AMBER LIGHT, 12V BRKT, LOWER WARNING LIGHT 86317500 CHARIOT SCRUBBER 11/15/08 SERIAL NO.
SERIAL NUMBERS REF. NO.
