Instructions / Assembly

ANIMATED WINDOW DISPLAY KIT
INSTRUCTION MANUAL
Please read the Instruction Manual carefully before operation.
Image System
TFT LCD
Color
24-bit RGB
Contrast Ratio
500:1
Keystone Correction
±15°
Native Resolution
1920x1080
Power Supply
12V
Lamp
30W LED
Power Consumption
35W
Lens
F=125
Media Input
USB/HDMI
Projection
Distance
1M-4.8M
Sound Output
3.5mm earphone
Aspect Ratio
16:9/4:3
Menu Languages
English, Spanish, French,
additional
Projection Size
25”~130”
Projector Components
Projector Keys on Projector
Remote Information
Remarks
1. The WindowFX kit is for indoor use only. Always operate in a dry environment.
2. For proper protection, please do not look directly into the lens during set up or
operation.
3. During operation, please keep the lens at least 3 feet from fabrics, such as window
curtains, furniture, or other flammable items.
4. Always operate in a ventilated area and do not block or cover the vents in the main
housing.
5. Please only use the provided adapter and power cord with the projector. Failure to
use these may create a fire hazard and may void any warranty.
6. For additional protection, please turn off the projector and remove the power supply
when not in use.
7. Please use original supplied box and packing material when transporting.
8. Never open the projector housing. Only authorized personnel should be allowed
access to the projector electronics.
9. For Adult use only. Not intended for the use by children under the age of 15.
10. Use only new, button cell battery (size CR2025) for the remote control.
11. To remove wrinkles in the projection material, use a low heat iron (on delicate or
silk setting) and lay a cotton towel or cloth between the iron and the projection
material. Do not make direct contact with the iron to the projection material. Never put
the projection material in the dryer.
12. Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
13. If you find any operational defects, please do not attempt to repair. Unplug the
projector immediately and call the Customer Service phone #: [phone]
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
a. Reorient or relocate the receiving antenna.
b. Increase the separation between the equipment and receiver.
c. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Supported File Formats
Multimedia Type File Formats Supported
Video AVI/FLV/MOV/MP4/MKV/RMVB
Setting up the Projector
The WindowFX Projector is designed to project from the inside of your home onto windows for
outside viewing or on a wall for inside viewing. Based on your viewing selection, either window
or wall, arrange your setup accordingly.
For Window Projection: the projector should be placed within 4 to 8 feet from the window you
will be using. Use the included projection screen material with the two-sided tape to attach to
your window or window frame.
For Wall Projection: the projector should be placed within 4 to 8 feet of the wall you will be
using. You may hang the included projection screen to your wall for increased image quality of
the projection.
Projector Operation
1. Begin by connecting the power adapter to the projector. Connect the power adapter to the AC
power outlet.
2. Power on the projector by pressing the power button on the projector. The projector is now
ON in active mode.
3. Adjust the focus of the projection by rotating the lens barrel.
4. If a slight trapezoid distortion is visible, move the Keystone wheel to adjust and square the
projected image.
5. Select Multimedia Icon (Image 1), then press OK on your remote or projector.
6. Select Preload Icon (Image 2), then press OK on your remote or projector.
Image 1 Image 2
7. On the next menu, select the orientation of the video to be projected, either horizontal or
vertical. Select the orientation by highlighting the folder and pressing the OK button. If the
desired orientation is vertical, the projector must be turned on its side (see images below).
8. On the next menu, select the season (Image 3) that you would like to play by highlighting the
desired folder and pressing the OK button. The Pre-loaded files will appear (Image 4).
9. To play all videos, press play on your remote or projector; to select specific videos, highlight
the videos and press OK on your remote or projector and a small checkmark will appear. After a
few seconds of non-activity, a small preview video will appear. To exit out of preview mode,
simply move using the arrow keys or press play and the videos will enter full screen format.
Image 3 Image 4
Bluetooth Setup
Set Bluetooth pairing on the Sound sub-menu. Defaulted setting is Bluetooth off. Click “right”
button, turn it ON. Then press “search” and find nearby device, max 5 devices. Select device for
pairing, it will show “Connected” once paired successfully. (See Images below)
Before connecting your own speaker or headphone device to projector for Bluetooth function,
please make sure these devices were clear up any hook up from other device, such as smart
phone and audio equipment. Otherwise projector will not “Search” them successfully. Our
Bluetooth module is suitable for connecting general speaker equipment, but no guarantee for all
market unit, preferred external speaker model you may visit our website-www.totalhomefx.com.
HDMI Setup
1. Press the Input/Source button on remote or projector and select HDMI. HDMI cable not
included.
Additional Operation Options
REPEAT: To repeat a video or all videos playing, press the repeat button on the remote. There are 3 possible
options for repeating: None, one video, or all videos.
REVERSE: Some videos have text which will need to be reversed when projecting onto a window to be
viewed outside the window. Press the rotate button on the remote to find the desired orientation.
TIMER: After selecting the videos to be played, press the MENU button on the remote or the projector. Use
the left or right arrow keys to cycle to the TIME menu. Select the number of minutes that the projector will play
and then turn off. There is no Auto On function.
QUICK MENU: While the video is playing, press the OK button to access the Quick Menu. The Quick Menu
includes further operational functions, such as Fast Forward, Rewind. There are also features to skip to the
next video or to return to the previous video.
1-888-476-7100
610 Academy Drive
Northbrook, IL 60062
www.TotalHomeFX.com
Visit our website for more information, to purchase additional downloadable videos, and to
submit a customer service request.
NO.
Definition
Purpose
1 Function
Keys
Operating keys
2 HDMI Slot
Insert HDMI Source
3 Keystone
Wheel
Adjust angle
distortion
4 IR Receiver Remote control
signal receiver
5 USB Port Insert USB
6 Power Input
Port
Insert power supply
adapter
7 3.5mm
Earphone
Port
Insert earphone or
speaker
8 Lens Barrel Adjust focus
HORIZONTAL ORIENTATION VERTICAL ORIENTATION
Note
: Please remove batteries
from remote for extended
periods of inactivity.
1 2 3
4 5
6