A few things before you get started: i) installing your Windmill AC should take © If you're looking for professional assistance, about 45 minutes we have some options for you windmillaircom/support im We recommend doing this with a helper (z= ) We're here if you need us, so don't hesitate to chat or email: windmillaircom/support IMPORTANT: Carefully read the entire installation guide and owner's anal before installing the unit This installation pride and the complete owner's manual are available at windrili
Safety first A General Installation Warnings & Cautions Follow all warnings and safety instructions, To avoid risk of personal injury, property damage, and product damages, pay close attention to the following during installation: The AC could Tall if it Is not properly installed, which could result in death or serious injury. Pay close attention to steps 2 and 3 to ensure you properly position and secure the AC in the window. The Windmill AC is heavy.
Window Requirements 23-37 inches inches The medium size (8K BTU} Windmill AC is designed for windows that slide up and down (double-hung windows) with a width of 23-37 inches and a vertical opening of at least 14 inches. Make sure your window is in good shape and can handle the weight of the AC for a long period of time. You'll also want to make sure there is at least 2 feet of clearance on all sides of your AC {including the front and back). This helps ensure walls and other objects don't block airflow.
What's in the box? SMALL STUFF 14" Borrows (79) The Windmill AC To simplify your setup, the AC comes with the top and bottom install bars, the front frame, side adapters, and both side panels per-assembled Adhesive & non-adhesive window: insulation foam (each) from Window sash lock (Ig Rubber screw holey plug x) *Please ensure that the front frame and both side panels are secured (and not damaged) before installing your AC.
Step 1. Insulate your window. Cut the adhesive foam to the width of your window. You should cut the foam to be the width of your window from the left to the right side. Make sure you're cutting the foam with the adhesive. Stick the adhesive foam across the underside of the front window sash.** Peel off the backing paper to expose the adhesive. Stick this side of the foam to the underside of your window sash (i.e.
bol ee Cut the non-adhesive foam to the height Insert the foam into the channels on of the bottom half of your window. both sides. Cut the non-adhesive insulation foam to fit the length of This should be the sides of the lower half of your window. the vertical side channels of the window frame. Your window's ready, now let's focus on your AC.
Step 2. Lift the AC into the window. Together with your helper, lift the assembled AC into the window frame. Make sure you do this step with a helper. Very carefully, lift the assembled AC into the window frame. Make sure someone is holding the back of the unit securely. eis helpful to rest the unit on the Inside window sill until you're ready to reposition k correctly. Injury {to you and others) and property damage can secure If not done correctly.
Vinyl Windows inside Duns ids: 1 you have storm windows, additional window setup Is required, Otherwise, the unit will til nto the room which could damage your floor and the unit) Please visit er rigid Outside Close the window down onto the AC, BEHIND the top bar. Once the AC is centered and the bottom bar is successfully positioned, close the window down onto the AC, behind the top bar. See diagram above. **Make sure the weight is supported before letting go of the back of the unit.
Step 3. Secure the AC. Use the side panels to fit the AC to the window. Extend the side panels out until they reach the window frames on each side. 15 Secure the AC using the included 1/2 inch screws. Now that your AC is in the right position, you'll need to secure it using the included %: inch screws. Locate the five screw hole locations on the unit and side panels as marked. Use the center screw hole on the top installation bar to secure your unit to the window frame.
Fill the center hole on the front frame with the included rubber plug. This will give your AC a clean, finished look. Nice and secure.
Step 4. Cut and attach the cosmetic panels. Determine the width of your side panels. This is the number on your side panel that falls just behind the edge of the front frame. The left and right numbers may be different if the AC is not perfectly centered in the window. 1° Find the corresponding number on your cosmetic panels. {Make sure you are using the correct panel. They are labeled “Left” and “Right”) Cut straight, along the respective line.
Insert the trimmed side panels into the front frame. Align and insert the end you just cut into the vertical channel on both sides of the front frame. It helps to insert the bottom corner first and then the top. Then gently push the panel into the slot. ™ e— Snap the prongs into place. Snap the three prongs into the corresponding slots on the ends of the side panels. Repeat on both sides. You're in business. Now for the last step.
Step 5. Lock and insulate your window. Option 1: Wood windows. Attach the sash lock as shown in the diagram above. = Option 2: Vinyl windows. Attach the sash lock as shown in the diagram above. A CAUTION: For vir! or similar windows, attach the bracket to the side jamb of the window [net the window itself]. See diagram above. This will hsp avoid broken glass and window damage.
4 Cut the non-adhesive insulation foam Use the nonadhesive foam to fill the to fit the width of your window. gaps in your window. Make sure you are cutting the foam with the non-adhesive Stuff it between the gap of the upper and lower sashes of sides. Measure and cut the foam to be the width of your your window. window from the left to right side. This will plug any alr gaps and help keep out bugs snd draft. That's it for installation! Just a few more things to check over, and then you can relax.
Some other things you may want to know. Connect your Windmill AC to your smartphone. To learn how to connect your Windmill AC to your smartphone and for app related questions, please go to windrmillaircom/support. 25 2 How to help the environment and save on your energy bill: « Clean your large mesh filter at least monthly (and if applicable, replace your activated carbon filter Avery 2-4 months). + Make sure nothing is blocking the air flow around your AC. We recommend a clearance of at least 2 feet.
3 To remove your AC from the window: 1. Turn off the AC and unplug the power cord. 2. Take out the insulation foam between the top and bottom window sashes. 3. Unscrew all screws securing the AC and side panels to the window frame or sill. 4. Remove the end caps and cosmetic panels. 8. Then, slide the side panels back in, towards the unit. &. Place a plastic bag or towel! on the floor under the unit {in case there is water in the unit from normal operation). 7.
