52 " Neopolis™ Indoor/Covered Outdoor Read and save these instructions Questions, problems, missing parts? Before resuming to your retailer, call our customer service department at 855-817-WIND (9463) 8 a.m. 5 p.m, EST, Monday-Friday &) @. DAMP Intertwine WR1476 SERIES Low 0.25 14.17 65 7.5kgs | 8.6kgs Medium 120 0.38 31.69 106 (16.5 Ibs) | (18.9 Ibs) High 0.54 64.4 176 4794 NOTE: These are approximate measures. They do not include amps and wattage used by the light kit.
EVE Tie 1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National Electrical Code “EXPANSION 70-1999” and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 3. The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 lbs.
Package contents Unpack your fan and check the contents. See page 2. You should have the following items: 1. Downed assembly (1} 2. Mounting bracket (1) i 3. Canopy (1) 4. Canopy cover (1) 5. Coupling cover Fan motor assembly (1) 7. Light Kit plate with 14W LED reassembled (1) 7 8. Extra Light Kit plate (1) (For WR1476MB only) — am 9. Glass shade (1) . fan 10. Blade (5) 11. Receiver with 6 wire nuts (1) p= 12. Transmitter + holder + mounting screws + A23 12 volt battery (1) — 13.
Hanging the fan WARNING: Please use all of the parts hardware and components provided by Wind River. The use of other parts, hardware or components not supplied by Wind River with the fan will void the Wind River Warranty. REMEMBER to turn off the power. Follow the steps below to hang your fan properly: Step 1. Attach the mounting bracket to the outlet box with two screws and washers provided with the outlet box. Make sure the mounting bracket is tight and secured. (Fig.5) Sept 2.
Ste ee ely [yee eg REMEMBER to shut the power off at the circuit breaker or fuse box. Step 1. Insert Receiver into Hanger Bracket with the flat side of the Receiver facing the ceiling. (Fig. 8) Step 2. Motor to Receiver Electrical Connections: Connect the WHITE wire from the fan to the WHITE wire marked “TO MOTOR N” from the Receiver. Connect the BLACK wire from the fan to the BLACK wire marked “TO MOTOR L” from the Receiver.
Finishing the installation Step 1. Remove one screw from the mounting bracket and loosen the other screw approximately 1/4 turn. Step 2. Carefully raise the canopy up to the mounting bracket, and ensure the loosened screw is inserted into the key hole on the canopy. Rotate the canopy clockwise. (Fig. 10) Step 3. Secure the canopy by replacing the screw previously removed and tightening the screw previously loosened. (Fig. 10) Step 4.
rte te Th 1s Step. Remove the 14W LED assembly from the light kit plate by removing three light kit plate screws. (Fig.12) Set these screws aside for use later. Step 2. Remove one of three screws from the fan motor assembly mounting ring and loosen, but do not remove, the other two Step 3. Place the key holes from the light kit plate over the two screws previously loosened from the fan motor assembly mounting ring. Turn the light kit plate until it locks in place at the narrow section of the key holes.
Tell engine ate eerie Note: The system is equipped with a leaning frequency function which has 16 code combinations to prevent potential interference from other remote units. The frequency on your receiver and transmitter units have been preset at the factory. No frequency change is necessary, should you desire to install another fan within the same home or area with a separate frequency code. please kindly see below instruction manual to learn how to change the frequency.
Install a 12V battery into the remote control. To prevent damage to the remote control, remove the battery if not used for long periods of time. um on the power and check the operation of your fan. Q and * * buttons: Tess hers buffoons are used to select the fan speed. Press and release the button of the desired speed setting: = Lowest speed © = Medium speed © = Highest speed b." ® ” button: This button will tum the light on or off and will also control the brightness setting.
Troubleshooting The fan will not start. Check main and branch circuit fuses or breakers. Check line wire connections to the fan and switch wire connections in the switch housing. The fan sounds noisy. Make sure all motor housing screws are snug. Make sure the screws that attach the fan blade arm to the motor hub are tight. Make sure wire nut connections are not rattling against each other or the interior wall of the switch housing. Allow a 24-hour "breaking-in" period.
