BEETLE iSPRINT POS System Operating Manual
BEETLE iSPRINT POS System Operating Manual Edition Jun 2006
Pentium™ is a registered trademark of the Intel Corporation BEETLE™ is a registered trademark of Wincor Nixdorf GmbH & Co. KG Copyright© Wincor Nixdorf GmbH & Co. KG, 2006 The reproduction, transmission or use of this document or its contents is not permitted without express authority. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Delivery subject to availability; technical modifications possible.
Contents Manufacturers Certification........................................ 1 Tested Safety...............................................................................1 FCC-Class A Declaration.............................................................1 BSMI (EMC for Taiwan) ...............................................................2 Note on Laser ..............................................................................2 Important notes ........................................................
CD-ROM Drive.........................................................................................19 Hard-Disk Drive........................................................................................19 USB Front Access....................................................................................19 Rear Panel connectors on Beetle iSPRINT................................20 12V Power Output Jack............................................................................21 24V Power Output Jack...
Appendix..................................................................... 39 Technical Data ...........................................................................39 Installation Specifications .........................................................................39 Environmental Conditions.........................................................................
Manufacturers Certification The device complies with the requirements of the EEC directive 89/336/EEC with regard to ‘Electromagnetic compatibility" and 73/23/ECC “Low Voltage Directive”. Therefore, you will find the CE mark on the device or packaging. Tested Safety The POS system has been provided with the symbol for “Tested Safety”. In addition, the BEETLE has received the UL symbol and cUL symbol.
BSMI (EMC for Taiwan) The device complies with the requirements of the BSMI (Bureau of Standards, Metrology and Inspection, Ministry of Economic Affairs) directive CNS14348 with regard to “Electromagnetic compatibility” with the limits for a Class B product. Note on Laser If your device is equipped with a CD-ROM drive, the following condition applies, The CD-ROM drive contains a ligh-emitting diode (LED), classified according to IEC 825-1:1993: LASER CLASS 1; it must not be opened.
Important notes The Modular POS system BEETLE iSPRINT conforms to the current safety standards for data processing equipment. If this device is taken from a cold environment into the operating room, moisture condensation may form. The device must be absolutely dry before being put into service; an acclimatization period of at least two hours must therefore be observed. This device is equipped with a safety-tested power cable and may be connected only to a prescribed grounded-contact power socket.
Replacing the Lithium Battery CAUTION: Incorrect replacement of the Lithium Battery may lead to a risk of explosion The lithium battery must be replaced by the end user only by identical batteries or types recommended by Wincor Nixdorf. Do not throw Lithium Batteries into the trashcan. It must be disposed of in accordance with local regulations concerning special waste Make sure that you insert the Battery the right way round. The plus pole must be on the top! Plus-Pole 2 u u 3 1 (1) Push the Latch.
AC Power Cord If the AC power cord is not provided with the device, the user has to ensure that a certified AC power cord is used as required by the Safety Regulation of the country. Please ensure that the AC power cord used is compliant with the safety approval according to the country, as listed below: Countries Safety Approvals USA UL Canada CSA Germany GS Japan PSE Taiwan BSMI China CCC For other countries not mentioned in the above list, please check with the local authority.
Introduction This manual describes the modular POS system BEETLE iSPRINT with a Pentium 4 processor. This documentation is intended to help you work with the POS system and to serve as a reference work. The detailed table of contents helps you find the desired information quickly and easily. The type and scope of application programs depend on the customer’s own selection; therefore, software will not be discussed further in this manual.
Symbol used in this manual NOTE ! Text following this symbol representing important notes to facilitate the use of the device and help avoid operating errors. CAUTION ! WARNING 01750096993 E Text following this symbol indicates the cautions to help you to avoid damaging of hardware or losing of data. Text following this symbol indicates the conditions that, if not being observed might cause personal injury.
Care of BEETLE iSPRINT ! CAUTION Clean your BEETLE iSPRINT at regular intervals with a suitable plasticsurface cleaner. Make sure that the power plug is disconnected, connector cables are unplugged and no liquid finds its way into the device. The glass surface of your Touch Screen should be cleaned with a mild, commercially available glass cleaning product. All pH neutral materials (pH 6 to 8) are to be used for cleaning purposes.
So don’t simply throw your BEETLE iSPRINT system on the scrap heap when it has served its time, but take advantage of the environmentally smart, up-to-date recycling methods! Please contact your competent branch office for information on how to return and re-use devices and disposable materials. Wincor Nixdorf is always ready to answer any questions you may have about our environmental protection policies. We look forward to your message.
Warranty Wincor Nixdorf guarantees a limited warranty engagement of 12 months beginning with the date of the delivery. This warranty engagement covers all those damages which occur despite a normal use of the product. Damages caused by improper or insufficient maintenance, improper use of the product or unauthorized modifications of the product, inadequate location and surroundings will not be covered under the warranty.
Abbreviations AGP AC97 BIOS BPP COM CPU CRT cUL DIMM ECP EPP EPROM FDD FC-PGA2 HDD IDE ISA ISO LAN LED LPT PCI PCMCIA PnP RAM ROM SIMM TFT UL USB 01750096993 E Accelerated Graphics Port Audio Codec ‘97 Basic Input Output System Bits per Inch Communication Port Central Processing Unit Cathode Ray Tube Canada Underwriters Laboratories Dual In line Memory Module Extended Capability Port Enhanced Parallel Port Erasable Programmable Read Only Memory Floppy Disk Drive Flip-Chip Pin Grid Array (Socket 478) Hard
Device Overview BEETLE iSPRINT is a modular POS system which is designed for low cost and high performance to complement the existing BEETLE product families.
Basic Operation Before switching on the system This section describes the setup of the system before switching on the system. Unpacking and checking the system Unpack the parts and check if the delivery matches the description on the delivery note. If damage has occurred during shipping or the package contents do not match the delivery note, promptly inform your Wincor Nixdorf sales outlet. NOTE Transport the device only in its original packaging to protect it against impact and shock.
Cabling of the system Follow the following steps when installing the cables of the system: Remove the cable cover, if present. Plug one end of the power cable into the socket of the BEETLE iSPRINT system and plug the other end of the power cable into the grounded socket at the main power supply. Plug in and secure all the required data cables. ! WARNING Always make sure that the system is switched off when you do any cabling works.
Opening / Closing the system It is easy to open and close the system during your access to the inside of the system. To open the system, press the lock (1) and at the same time, push and slide the cover plate towards direction (2). (1) Press (2) Slide To close the system, align the cover plate on the sliding slot of the system. Push towards direction (1) and make sure the cover plate is closely sealed with the system.
Switching on / off the system To switch ON the BEETLE iSPRINT system, Switch on the power supply switch at the rear side. Push the ON/OFF button at the front of the system. To switch OFF the BEETLE iSPRINT system, 16 Push the ON/OFF button at the front of the system. Switch off the power supply switch at the rear side. Remove the AC power cord from the system.
BEETLE iSPRINT system – The components Function & Indicators on BEETLE iSPRINT The illustration below shows the possible components of the BEETLE iSPRINT system.
ON/OFF Button This is a soft touch power button that replaces the main power switch that turns your system on and off. From an OFF state, you can switch the system ON by simply pressing the ON/OFF button. From an ON state, you can also switch the system OFF by pressing and holding the ON/OFF button for four (4) seconds. The functions of the power button can also be altered in the Power Management section of the CMOS setup.
CD-ROM Drive The BEETLE iSPRINT system is equipped with a CD-ROM drive of 52x or higher. Hard-Disk Drive The BEETLE iSPRINT system can be equipped with a 3½” PCI-IDE hard-disk drive. The storage capacity of the hard-disk is 40 GB or higher, up to 137 GB. USB Front Access The BEETLE iSPRINT provides one USB port for connection of the USB device from the front side.
Rear Panel connectors on BEETLE iSPRINT The illustration below shows parts of the rear panel of the BEETLE iSPRINT system, with the position of the connecting sockets and connectors.
12V Power Output Jack The BEETLE iSPRINT is equipped with a 12VDC output supplying to a maximum of 2A for powering a LCD display. 24V Power Output Jack The BEETLE iSPRINT is equipped with a 24VDC output supplying to a maximum of 3A for powering a printer. Expansion Slots The BEETLE iSPRINT has two PCI bus master expansion slots on board. One of the slot is designed for the Riser Card. Power Supply Unit The power supply unit automatically adjusts itself to the particular voltage.
Mouse Connector (PS/2) The BEETLE iSPRINT system has a Light-green 6-pin Mini-DIN Jack for connecting a standard Mouse using a PS/2 plug. Parallel Port LPT1 for Modular Printer (Optional) The parallel port LPT1 on the BEETLE iSPRINT system could be connected to a modular printer. Standard Serial Port (COM1) The BEETLE iSPRINT is equipped with a standard serial port, which is assigned as COM1. It is a serial interface that is used for standard PC peripherals.
Line-in socket: allows a headphone or preferably a set of powered speakers to be connected to the system to output voices. Line-in socket: allows tape player or other audio sources to be recorded by the POS system or played through the Line-out socket. MIC socket: allows a microphone to be connected to the system to input voices.
BEETLE iSPRINT Motherboard Motherboard Block Diagram FC-PGA2 478 Socket DVO single channel DDR SDRAM Intel 845GV GMCH 1.6 GB/s 2.1 GB/s 1.
Processor Supports The BEETLE iSPRINT support the processor with FC-PGA2 478 socket. However, below is the list of supported processors that have been certified for the use on this motherboard with the manufacturer’s standard and certification compliances: FC-PGA2 478 Intel Pentium 4 processor 2.0GHz FC-PGA2 478 Intel Pentium 4 processor 2.8GHz FC-PGA2 478 Intel Celeron processor 2.0GHz FC-PGA2 478 Intel Celeron processor 2.
Graphics Subsystem The BEETLE iSPRINT motherboard is equipped with the Northbridge internal graphic accelerator to provide graphic support to the system. This internal graphic accelerator is able to provide simultaneous video output via an on-board 15-pin DSUB and to a TFT Flat Panel LCD display through Wincor Nixdorf Panellink card. CRT Display The GMCH has an integrated 350MHz RAMDAC capability to drive a standard progressive scan monitor with the resolution up to 2048 x 1536 with 2-bit color at 60 Hz.
Audio Subsystem The BEETLE iSPRINT motherboard is equipped with an integrated AC97 controller which is AC 97 2.2 compliant. Additionally, the motherboard also consists of an on-board power amplifier with an output of 4 Watt, which will be output of 2 Watt per channel. However, the jumper setting in the audio subsystem could be used to bypass the power amplifier to become Lineout. The audio connectors available include: Back panel audio jacks for Speaker-out/Line-out, Line-in and Mic-in.
System BIOS The system is equipped with AWARD BIOS. The BIOS has a 2 MB flash EPROM. It could be upgraded from diskette using a utility provided. Plug-and-Play The BIOS is able to automatically configure the PCI devices and Plugand-Play devices. These devices can either be on-board or in the PCI add-on slots. The Plug-and-Play BIOS supports Plug and Play specification 1.1.
DC Power Output The 12 VDC output supplies to a maximum of 2A for powering a LCD display. Non-volatile Memory The BEETLE iSPRINT is equipped with non-volatile memory, supports up to 64 kb. Default memory size provided is 4 kb.
System BIOS This section describes the AWARD BIOS™ Setup program built into the ROM BIOS. The Setup program allows users to modify the basic system configuration. The BIOS information is stored in a batterybacked RAM so that it retains the Setup information when the power of the system is turned off. The BIOS reads the system information contained in the CMOS and begins the process of checking out the system and configuring it.
BIOS Setup Main Menu The following table describes the BIOS setup options available from the BIOS Setup main menu: BIOS Setup Option Standard CMOS Features Description To setup basic system configuration such as date, time, type of floppy etc. Advanced BIOS Features To setup the advance settings available on the system. Advanced Chipset Features To setup the contents of the chipset register and optimize the system’s performance.
To load the BIOS default, from the dialog box, choose ‘Y’ followed by [ENTER] key. To exit this section without loading the BIOS default, from the dialog box, choose ‘N’ followed by the [ENTER] key. Load Optimized Default NOTE Supervisor/User Password NOTE Save & Exit Setup NOTE Exit Without Saving NOTE 32 To load the BIOS default values that are factory settings for optimal performance system operations.
POST Messages During the Power On Self-Test (POST), if the BIOS detects an error requiring you to do something to fix, it will either sound a beep code or display a message. If a message is displayed, it will be accompanied by: PRESS F1 TO CONTINUE, CTRL-ALT-ESC OR DEL TO ENTER SETUP POST Beep Currently there are two kinds of beep codes in BIOS. This code indicates that a video error has occurred and the BIOS cannot initialize the video screen to display any additional information.
a system disk into Drive A: and press [Enter]. If you assumed the system would boot from the hard drive, make sure the controller is inserted correctly and all cables are properly attached. Also be sure the disk is formatted as a boot device. Then reboot the system. DISKETTE DRIVES OR TYPES MISMATCH ERROR - RUN SETUP Type of diskette drive installed in the system is different from the CMOS definition. Run Setup to reconfigure the drive type correctly.
ERROR ENCOUNTERED INITIALIZING HARD DRIVE Hard drive cannot be initialized. Ensure that the adapter is installed correctly and all cables are correctly and firmly attached. Also ensure that the correct hard drive type is selected in Setup. ERROR INITIALIZING HARD DISK CONTROLLER Cannot initialize the controller. Make sure that the cord is correctly and firmly installed in the bus. Ensure that the correct hard drive type is selected in Setup.
Memory parity Error at ... Indicates the memory parity error at a specific location. You can use this location along with the memory map for your system to find and replace the bad memory chips. MEMORY SIZE HAS CHANGED SINCE LAST BOOT Memory has been added or removed since the last boot. In EISA mode use Configuration Utility to reconfigure the memory configuration. In ISA mode enter Setup and enter the new memory size in the memory fields. Memory Verify Error at ...
Should Be Empty But EISA Board Found PLEASE RUN EISA CONFIGURATION UTILITY A valid board ID was found in a slot that was configured as having no board ID. NOTE; When this error appears, the system will boot in ISA mode, which allows you to run the EISA Configuration Utility. Should Have EISA Board But Not Found PLEASE RUN EISA CONFIGURATION UTILITY The board installed is not responding to the ID request, or no board ID has been found in the indicated slot.
FLOPPY DISK(S) fail (80) Unable to reset floppy subsystem. FLOPPY DISK(S) fail (40) Floppy Type mismatch. Hard Disk(s) fail (80) HDD reset failed Hard Disk(s) fail (40) HDD controller diagnostics failed. Hard Disk(s) fail (20) HDD initialization error. Hard Disk(s) fail (10) Unable to recalibrate fixed disk. Hard Disk(s) fail (08) Sector Verify failed. Keyboard is locked out - Unlock the key. BIOS detect the keyboard is locked. P17 of keyboard controller is pulled low.
Appendix Technical Data Installation Specifications BEETLE iSPRINT System Width Depth Height 372 mm 385 mm 105 mm Weight approx. 11 kg Environmental Conditions Operating IEC 721-3-3 Transport IEC 721-3-3 Storage IEC 721-3-3 Input voltage 100 - 120 VAC 200 - 240 VAC Max.
Published by Wincor Nixdorf Pte Ltd 2, Kallang Sector Singapore 349277 Part No.
