POS Board For D2 Basic CPU Product Manual
We would like to know your opinion on this publication. Please send us a copy of this page if you have any contructive criticism. We would like to thank you in advance for your comments. With kind regards, Wincor Nixdorf International GmbH Dokumentation RS PD1 Wernerwerkdamm 16 Gebäudegruppe 36 D-13629 Berlin E-Mail: retail.documentation@wincor-nixdorf.com Your opinion: Order No.
POS Board For D2 Basic CPU Product Manual Edition September 2002
MS-DOS® and Microsoft® are registered trademarks of Microsoft Corporation. BEETLE® is a registered trademark of the Wincor Nixdorf International GmbH Copyright © Wincor Nixdorf International GmbH, 2002 The reproduction, transmission or use of this document or its contents is not permitted without express authority. Offenders will be liable for damages.All rights, including rights created by patent grant or registration of a utility model or design, are reseverd.
Contents Introduction......................................................................................... 1 Connector Assignment ...................................................................... 4 COM3, 4, 6 (INTERNAL CONNECTOR) .............................................. 4 Connector Type................................................................................ 4 Connector Assignment:....................................................................
Introduction Introduction The POS Board is designed for the motherboard “D2 Basic”, as additional COM ports and the cash drawer Interface were needed. The POS Board has implemented the RS232 standard interfaces for COM3, COM4, COM6 and the reduced RS232 Interface (TxD and RxD only) COM5 for the touch functionality (COM6 is provided for future applications). The POS Board integrates the Cash Drawer Logic as well as the power supply generation for the cash drawer.
Introduction COM5 (internal for Touch function) For COM3 and COM4 the Standard RS232 connectors are available at the bracket of the BEETLE /iPOS. Cables connect the POS Board and the RS232 Connectors at the bracket. Depending on the type of POS board the COM Interfaces use the following I/O addresses and interrupts.
Introduction POS Board Type I POS Board Type II (01750045096, D) Requirement: WN BAS BIOS 40/11 or higher (01750056648, A) Requirement: WN BAS BIOS 41/12 or higher COM3 COM4 I/O Address 3E8 - 3EF 270 - 277 IRQ 10 10 COM5 COM6 2E0 - 2E7 328 - 32F (5), 12 11 I/O Address 3E8 - 3EF 210 - 217 (230 - 237) 250 - 257 270 - 277 2E0 - 2E7 328 - 32F IRQ 10 10 (5), 12 11 () = Default Locations for the COM cable connectors on the POS Board: Material No.
Connector Assignment Connector Assignment COM3, 4, 6 (INTERNAL CONNECTOR) Each of the three interfaces is routed to a 2x7 pin connector, which could be equipped with a wired 9-pin DSUB male connector to have the PCStandard Interface. The DSUB connector has to be mounted to the chassis of the BEETLE - Box.
Connector Assignment Preparing the POSBOARD for the Touch Screen Installation Run the BIOS Setup utility. Switch the system on and press «F2» key during the “Power-onSelf-Test”. Choose the “Avanced” menu. Press right or left arrow-key until “Advanced” is highlighted and select «I/O Device Configuration» with arrow key. Press «Enter» and select «Touch Screen Routing» with the arrow key. Set «Route to COM5» by using the space bar to toggle. Choose the “Exit” menu. Press «ESC» twice.
Connector Assignment BIOS Settings I/O Device Configuration: Touch Screen Routing to COM5 I/O for COM4 230 for Type II; 270 for Type I IRQ for COM3, COM4 IRQ 10 IRQ for COM5 IRQ 5 (Default) PCI / PNP ISA IRQ Resource Exclusion: IRQ 10 Reserved IRQ 5 (Default) Reserved IRQ 5 is the default setting.
Connector Assignment RJ12 Connector Pin Usage PIN Description 1 Frame Ground 2 Opening pulse for cash drawer 3 Status cash drawer 4 +24 V DC 5 6 n.c. Signal Ground The Wincor Nixdorf cash drawers KA16, KA17 and KA18 are connected by cash drawer cables (CR KB - 0930; CR KB - 0930; CR KB - 0941, cable lengths: 0.8m; 1.5m; 5.0m).
Installation of COM Ports Installation of COM Ports With Windows or Linux operating systems pre-installed by Wincor Nixdorf, all COM interfaces have already been installed. Please note the installation for the Touch Screen (see chapter “Preparing the POSBOARD for the Touch Screen Installation”, page 5) This section describes the installation of COM ports on BEETLE /iPOS systems, that were not pre-installed by Wincor Nixdorf.
Installation of COM Ports Confirm by a click on OK but do not reboot the BEETLE when prompted! Continue with „ADD NEW“ until you reach COM5: Then continue with next topic. Reboot the BEETLE when prompted! Set the Windows registry key HKLM\Software\Services\Serial\permit_share to 1 for correct function of OPOS - see also OPOS manual! If your application runs in multiple windows and you want to avoid continuous close / open sessions of COM ports in your application, you need this feature, too.
Installation of COM Ports Do not install Intel´s ultra ATA driver. Conflicts between the driver and COM4 might occur while following installation steps. Run START Æ SETTINGS Æ CONTROL PANEL and leave the window open until restart of Windows. Click SYSTEM in CONTROL PANEL window, change to tab HARDWARE and select ADD NEW HARDWARE and confirm the following dialogs. You need to let Windows first search for new Plug and Play (PnP) devices.
Installation of COM Ports DO NOT RESTART COMPUTER WHEN REQUESTED ! Repeat the last two steps for COM4: up to COM5: (COM6: if wanted) After all COM ports are installed, restart Windows. Set the Windows registry key HKLM\Software\Services\Serial\permit_share to 1 for correct function of OPOS (refer to OPOS manual). If your application runs in multiple windows and you do want to avoid continuous close / open sessions of COM ports in your application, you need this feature too.
Installation of COM Ports Open SYSTEM DEVICES Æ Plug and Play BIOS, set Disable NVRAM / ESCD updates and confirm. Click ADD NEW HARDWARE in CONTROL PANEL window Confirm following hints and select NO, the device isn’t in the list. Windows will offer to search for new hardware Æ confirm and wait... Confirm, when asked. Now, COM3: and COM4: are installed. Again, click ADD NEW HARDWARE in CONTROL PANEL window. Like before select NO, the device isn’t in the list, but don’t let Windows search.
Installation of COM Ports Linux Install Linux from CD. Enter „man setserial“ and read general info about installation of COM ports. Add following lines to /etc/rc.d/rc.
Published by Wincor Nixdorf International GmbH, 2002 D-33094 Paderborn Printed in Singapore Order No.
