OWNER’S OPERATING & MAINTENANCE MANUAL PATENT PENDING PLEASE DO NOT DISCARD THIS MANUAL! KEEP FOR FUTURE REFERENCE AND TRAINING
TABLE OF CONTENTS IMPORTANT SAFETY INFORMATION........................................................................................ 3-5 ASSEMBLY INSTRUCTIONS......................................................….............................................. 6-7 ATTENDANT OPERATING INSTRUCTIONS............................................................…............... 8-13 OCCUPANT OPERATING INSTRUCTIONS...............................................................................
IMPORTANT - PLEASE READ FOR PRODUCTS WITH POWERED OPTIONS (Heat, Massage, etc...) IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS (Read all instructions before using this product.) When using an electrical appliance, basic precautions should always be followed, including the following: DANGER - To reduce the risk of electric shock always unplug this product from the electrical outlet before cleaning, maintenance or servicing. WARNING: 1.
IMPORTANT - PLEASE READ For Heat & Heat and Massage Chairs This equipment is marked with the industry recognized symbol indicating it is a “Class II Double-Insulated” device as defined by IEC 60601-1. As such, it does NOT require a three conductor power cord (i.e. one with a ground connection) for safety purposes. While the equipment can be safely operated with no ground connection, a three conductor power cord is provided to satisfy customer expectations for typical equipment configuration.
IMPORTANT - PLEASE READ BASIC SAFETY PRECAUTIONS: 1. READ AND FOLLOW ALL DIRECTIONS. 2. CAUTION: Use slide-out foot support with staff assistance only. 3. DO NOT put hands, feet, or clothing into any openings when changing positions on recliner. Attendant MUST confirm that users arms, legs, hands and feet are clear while changing recliner positions or SERIOUS INJURY MAY OCCUR. 4. Lock casters at all times, except when transporting chair. 5. STAY CLEAR of the recliner mechanisms when operating chair. 6.
ASSEMBLY INSTRUCTIONS PREPARATION: 1. Carefully examine your product for any damage. Inspect all components. IF DAMAGE IS EVIDENT, REFUSE SHIPMENT, & CONTACT FREIGHT CARRIER OR WINCO IMMEDIATELY. 2. Remove all packaging material that was secured for shipping. 3. Carefully remove the product from the carton. 4. Save all boxes and packaging material until after you have assembled your product and have verified that all components are functioning properly. BACK ASSEMBLY INSTRUCTIONS: 1.
ASSEMBLY INSTRUCTIONS BACK ASSEMBLY INSTRUCTIONS: 5. Slide the back onto the recline mechanism until the middle hole of the mounting bracket (A) is aligned with the middle hole of the recline mechanism (B). 5 6. Install knobs (tethered to back) and tighten to a secure fit. 6 7. Ensure that the rear apron rests OVER the rear brace of chair. 7 IMPORTANT: • Test to ensure the back has been properly installed by pulling up on the back's push handle. The back should remain securely in place.
ATTENDANT OPERATING INSTRUCTIONS CASTER OPERATION: Lock/Unlock This chair features two types of casters, rigid and total-lock. 1 The front two casters are rigid casters. They are NOT designed to swivel in order to facilitate stable straight steering. In addition, the locking tab is always accessible. When locking tab is engaged, caster wheel will NOT roll. The rear two casters are total-lock casters. They are designed to swivel 360°.
ATTENDANT OPERATING INSTRUCTIONS RECLINE CHAIR FROM ATTENDANT POSITION: Attendant should be positioned on the RIGHT or LEFT side of chair 1 A 2 A 1. While occupant is seated in the chair, use one hand to operate the recline lever, located on either side of chair, to activate the legrest into its raised position. 2.
ATTENDANT OPERATING INSTRUCTIONS PLACING CHAIR INTO TRENDELENBURG: (Attendant ONLY) Attendant should be positioned on the RIGHT or LEFT side of chair 1 1. While occupant is in the chair, place the chair into the fully reclined position. (SEE "Recline Chair From Attendant Position" pg.9) 2. Once chair is fully reclined, attendant can push down near the rear of Trendelenburg lever (A) with their foot, allowing it to move down and forward. 2 3 1 2 3.
ATTENDANT OPERATING INSTRUCTIONS SWING-ARM OPERATION: (Attendant ONLY) Attendant should be positioned on the RIGHT or LEFT side of chair 1 1. TO OPEN: Press down on red latch handle to unlock Swing-Arm. WARNING: • Do NOT leave occupant unattended with either or both swingarms unlatched. • Do NOT transport chair with swing-arms unlatched 2. TO CLOSE: Push Swing-Arm firmly against frame. Latch will automatically engage with an audible "click".
ATTENDANT OPERATING INSTRUCTIONS TRANSFER OF OCCUPANT TO CHAIR: Attendant should be positioned on the RIGHT or LEFT side of chair 2 1. Lock all four casters. 2. Place chair into seated or reclined position relative to the position from which occupant is being transferred. (See pg.9) 3. Unlatch one swing-arm and place it into the 180° position. 4. Position gurney or wheel chair next to the chair on the side with the open swing-arm. 5.
ATTENDANT OPERATING INSTRUCTIONS SIDE-TABLE OPERATION: (OPTIONAL FEATURE) 1. TO RAISE TABLE: Grasp center of table and gently lift into place. Side-table will lock into place with an audible "click" once fully extended. 1 WARNING: • DO NOT lean or sit on side tables. • DO NOT use table for support or assistance when exiting or entering the chair. • Keep hands and objects clear of the moving parts of the table mechanism. IMPORTANT: • Side-tables have been rated for a MAXIMUM weight capacity of 20 lbs. (9.
OCCUPANT OPERATING INSTRUCTIONS RECLINE WHILE IN THE SEATED POSITION: 1. While seated in the chair, pull back on either of the recline levers (A), located on either side of chair, to activate the legrest into the recline position. 2. To operate the infinite back positioning, pull back on the recline lever and adjust the upholstered back angle by pushing back with your body until desired angle has been reached.
OCCUPANT OPERATING INSTRUCTIONS OPTIONAL HEAT & MASSAGE OPERATION: Control is located on the inside of right arm of chair. (Right is determined - as if sitting in the chair) HEAT OR HEAT ONLY MASSAGE Heating: (Heating elements are located in the seat & back of chair) Push HEAT button - See indicator light on switch 3 Lights = High Heat / Bright Light 2 Lights = Medium Heat / Med Light 1 Lights = Low Heat / Dim Light No Light = HEAT OFF Allow 5-8 minutes for back and seat to warm to desired setting.
GENERAL MAINTENANCE GAS SPRING RELEASE ADJUSTMENT: If recline levers fail to operate properly, adjust the gas spring using the instructions below. 1 1. Open swing-arms, lift safety aprons and remove (4) wing-nuts from seat mechanism. (2 on either side of chair) WARNING: • ENSURE heating wire for seat is clear of all moving parts of the mechanism during installation. • UNPLUG power cord from power source BEFORE cleaning. 2. Chair WITHOUT Heat & Massage: a. Lift seat off of mechanism and set aside.
GENERAL MAINTENANCE GAS SPRING RELEASE ADJUSTMENT: (continued) Chair will not recline: 5 6 5. If chair will NOT recline when left or right recline levers are pulled, rotate the gas spring clockwise (A) half (1/2) of a revolution (or 180°). Chair reclines without the use of recline levers: 6. If the chair reclines without the use of recline levers, rotate the gas spring counter-clockwise (B) half (1/2) of a revolution (or 180°). 7. After adjustment; Replace Clevis Pin and Bow-Tie Cotter Pin. 8.
INVERNESS RECLINER SPECIFICATIONS 24-Hour Chair - Specifications Seat Height ........................ ..25.5" to Foot Plate................19" Seat Width (arm to arm)........ ..26" Back Height Above Seat....... 28.75" Seat Depth............................ 21" Weight .................................. 199lbs. Overall Height .........................51.5" Overall Width (Trays Down)....39" (Trays Up)...... ..56.25" (Arms at 180°)..33.5" Maximum Weight Capacity....500 lbs. 18 Copyright 2016, WINCO MFG.
INVERNESS RECLINER OPTIONS Heat & Massage Side-Table Pivot-Table HM .....................................Heat & Massage HT ..............................................Heat ONLY FACTORY INSTALLED ONLY Available on LEFT, RIGHT, or BOTH sides (Also available with Wood Finish) Available on LEFT, RIGHT, or BOTH sides (Marine Board Only) Accessory Holder Available on LEFT, RIGHT, or BOTH sides IV Pole & Attachment ARMREST COVERS IV................................ IV Pole & Attachment AIRX...............
ARMREST COVER OPTION INSTRUCTIONS Installing Armrest Covers with Side Tables: 1. Raise the side table by grasping the center of the table and gently lift into place. 1 2 3 4 5 6 2. Locate large square opening in cover and position over the side table. Stretch the opening over the side table and slide over side table. 3. Fit the front portion of the Armrest cover over the front of the arm. Pull down tight for best fit. 4. Fit the rear portion of the Armrest cover over the rear of the arm. 5.
ARMREST COVER OPTION INSTRUCTIONS Installing Armrest Covers with Pivot Tables: 1. Loosen pivot table knob. 1 2 3 4 2. Remove pivot table by pulling straight up on pivot table. 3. Find pivot table opening in armrest cover located in the upper front portion of the armrest cover. 4. Place pivot table opening over pivot table bracket and fit armrest cover over the front portion of the arm. 5 5. Fit the rear portion of the Armrest cover over the rear of the arm. 6.
ARMREST COVER OPTION INSTRUCTIONS Installing Armrest Covers with IV Poles: 1. Using a Phillips screw driver, remove the top screw mounting the IV bracket to the arm and loosen the bottom screw enough to allow the bracket to move. (Be careful not to allow the bracket to damage the vinyl) 1 2 3 4 2. Fit the armrest cover over the rear of the arm and pull tight. 3. Use the Phillips screw driver to punch a hole in the armrest cover in line with the top mounting hole for the IV bracket. 4.
This page intentionally left blank 23 Copyright 2016, WINCO MFG.
LIMITED WARRANTY TERMS Winco Mfg., LLC. warrants this product to be free of manufacturer’s defects in material and workmanship, provided that the product is used according to normal operating conditions and proper maintenance intended by manufacturer. This warranty is available only to the original retail purchaser, is non-transferable and commences on the date of retail sale; proof of purchase required. LIMITED ONE YEAR COMPLETE PRODUCT WARRANTY: Winco Mfg.
