OWNER’S OPERATING & MAINTENANCE MANUAL PATENT PENDING PLEASE DO NOT DISCARD THIS MANUAL! KEEP FOR FUTURE REFERENCE AND TRAINING
TABLE OF CONTENTS IMPORTANT SAFETY INFORMATION........................................................................................ 3-4 ASSEMBLY INSTRUCTIONS......................................................….............................................. 5-6 ATTENDANT OPERATING INSTRUCTIONS............................................................…............... 7-11 OCCUPANT OPERATING INSTRUCTIONS...............................................................................
IMPORTANT - PLEASE READ FOR PRODUCTS WITH POWERED OPTIONS (Heat, Massage, etc...) IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS (Read all instructions before using this product.) When using an electrical appliance, basic precautions should always be followed, including the following: DANGER - To reduce the risk of electric shock always unplug this product from the electrical outlet before cleaning, maintenance or servicing. WARNING: 1.
IMPORTANT - PLEASE READ BASIC SAFETY PRECAUTIONS: 1. READ AND FOLLOW ALL DIRECTIONS. 2. CAUTION: Use slide-out foot support with staff assistance. 3. DO NOT put hands, feet, or clothing into any openings when changing positions on recliner. Attendant MUST confirm that users arms, legs, hands and feet are clear while changing recliner positions or SERIOUS INJURY MAY OCCUR. 4. Lock casters at all times, except when transporting chair. 5. STAY CLEAR of the recliner mechanisms when operating chair. 6.
ASSEMBLY INSTRUCTIONS PREPARATION: 1. Carefully examine your product for any damage. Inspect all components. IF DAMAGE IS EVIDENT, REFUSE SHIPMENT, & CONTACT FREIGHT CARRIER OR WINCO IMMEDIATELY. 2. Remove all packaging material that was secured for shipping. 3. Carefully remove the product from the carton. 4. Save all boxes and packaging material until after you have assembled your product and have verified that all components are functioning properly. BACK ASSEMBLY INSTRUCTIONS: 1.
ASSEMBLY INSTRUCTIONS BACK ASSEMBLY INSTRUCTIONS: 5. Slide the back onto the recline mechanism until the middle hole of the mounting bracket (A) is aligned with the middle hole of the recline mechanism (B). 5 6. Install knobs (tethered to back) and tighten to a secure fit. 6 7. Ensure that the rear apron rests OVER the rear brace of chair. 7 IMPORTANT: • Test to ensure the back has been properly installed by pulling up on the back's push handle. The back should remain securely in place.
ATTENDANT OPERATING INSTRUCTIONS CASTER OPERATION: Lock/Unlock This chair features two types of casters, rigid and total-lock. 1 The front two casters are rigid casters. They are NOT designed to swivel in order to facilitate stable straight steering. In addition, the locking tab is always accessible. When locking tab is engaged, caster wheel will NOT roll. The rear two casters are total-lock casters. They are designed to swivel 360°.
ATTENDANT OPERATING INSTRUCTIONS RECLINE CHAIR FROM ATTENDANT POSITION: Attendant should be positioned on the RIGHT or LEFT side of chair 1 A 2 A 1. While occupant is seated in the chair, use one hand to operate the recline lever, located on either side of chair, to activate the legrest into its raised position. 2.
ATTENDANT OPERATING INSTRUCTIONS PLACING CHAIR INTO TRENDELENBURG: (Attendant ONLY) Attendant should be positioned on the RIGHT or LEFT side of chair 1 1. While occupant is in the chair, place the chair into the fully reclined position. (SEE "Recline Chair From Attendant Position" pg.8) 2. Once chair is fully reclined, attendant can push down near the rear of Trendelenburg lever (A) with their foot, allowing it to move down and forward. 2 3 1 2 3.
ATTENDANT OPERATING INSTRUCTIONS SWING-ARM OPERATION: (Attendant ONLY) Attendant should be positioned on the RIGHT or LEFT side of chair 1 1. TO OPEN: Press down on red latch handle to unlock Swing-Arm. WARNING: • Do NOT leave occupant unattended with either or both swingarms unlatched. • Do NOT transport chair with swing-arms unlatched 2. TO CLOSE: Push Swing-Arm firmly against frame. Latch will automatically engage with an audible "click".
ATTENDANT OPERATING INSTRUCTIONS TRANSFER OF OCCUPANT TO CHAIR: Attendant should be positioned on the RIGHT or LEFT side of chair 2 1. Lock all four casters. 2. Place chair into seated or reclined position relative to the position from which occupant is being transferred. (See pg.8) 3. Unlatch one swing-arm and place it into the 180° position. 4. Position gurney or wheel chair next to the chair on the side with the open swing-arm. 5.
OCCUPANT OPERATING INSTRUCTIONS RECLINE WHILE IN THE SEATED POSITION: 1. While seated in the chair, pull back on either of the recline levers (A), located on either side of chair, to activate the legrest into the recline position. 2. To operate the infinite back positioning, pull back on the recline lever and adjust the upholstered back angle by pushing back with your body until desired angle has been reached.
OCCUPANT OPERATING INSTRUCTIONS OPTIONAL HEAT & MASSAGE OPERATION: Control is located on the inside of right arm of chair. (Right is determined - as if sitting in the chair) HEAT OR HEAT ONLY MASSAGE Heating: (Heating elements are located in the seat & back of chair) Push HEAT button - See indicator light on switch 3 Lights = High Heat / Bright Light 2 Lights = Medium Heat / Med Light 1 Lights = Low Heat / Dim Light No Light = HEAT OFF Allow 5-8 minutes for back and seat to warm to desired setting.
GENERAL MAINTENANCE GAS SPRING RELEASE ADJUSTMENT: If recline levers fail to operate properly, adjust the gas spring using the instructions below. 1 1. Open swing-arms, lift safety aprons and remove (4) wing-nuts from seat mechanism. (2 on either side of chair) WARNING: • ENSURE heating wire for seat is clear of all moving parts of the mechanism during installation. • UNPLUG power cord from power source BEFORE cleaning. 2. Chair WITHOUT Heat & Massage: a. Lift seat off of mechanism and set aside.
GENERAL MAINTENANCE GAS SPRING RELEASE ADJUSTMENT: (continued) Chair will not recline: 5 6 5. If chair will NOT recline when left or right recline levers are pulled, rotate the gas spring clockwise (A) half (1/2) of a revolution (or 180°). Chair reclines without the use of recline levers: 6. If the chair reclines without the use of recline levers, rotate the gas spring counter-clockwise (B) half (1/2) of a revolution (or 180°). 7. After adjustment; Replace Clevis Pin and Bow-Tie Cotter Pin. 8.
INVERNESS RECLINER SPECIFICATIONS 24-Hour Chair - Specifications Seat Height ........................ ..25.5" to Foot Plate................19" Seat Width (arm to arm)........ ..26" Back Height Above Seat....... 28.75" Seat Depth............................ 21" Weight .................................. 199lbs. Overall Height .........................51.5" Overall Width (Trays Down)....39" (Trays Up)...... ..56.25" (Arms at 180°)..33.5" Maximum Weight Capacity....500 lbs. 16 Copyright 2014, WINCO MFG.
INVERNESS RECLINER OPTIONS Heat & Massage HM .....................................Heat & Massage HT ..............................................Heat ONLY FACTORY INSTALLED ONLY IV Pole & Attachment IV................................ IV Pole & Attachment Side-Table Available on LEFT, RIGHT, or BOTH sides Accessory Holder Available on LEFT, RIGHT, or BOTH sides 17 Copyright 2014, WINCO MFG.
LIMITED WARRANTY TERMS Winco Mfg., LLC. warrants this product to be free of manufacturer’s defects in material and workmanship, provided that the product is used according to normal operating conditions and proper maintenance intended by manufacturer. This warranty is available only to the original retail purchaser, is non-transferable and commences on the date of retail sale; proof of purchase required. LIMITED ONE YEAR COMPLETE PRODUCT WARRANTY: Winco Mfg.
