Datasheet
13
01-02
Typical dimensions
for taping configuration
Dimensions for radial taping
Designation Symbol PCM 2.5 taping PCM 5 taping PCM 7.5 taping PCM 10 taping* PCM 15 taping* PCM 22.5 taping PCM 27.5 taping
Carrier tape width W 18.0
p0.5 18.0 p0.5 18.0 p0.5 18.0 p0.5 18.0 p0.5 18.0 p0.5 18.0 p0.5
Hold-down tape width W
0
6.0
for hot-sealing
6.0
for hot-sealing
12.0
for hot-sealing
12.0
for hot-sealing
12.0
for hot-sealing
12.0
for hot-sealing
12.0
for hot-sealing
a dhesive tape adhesive tape adhesive tape a dhesive tape a dhesive tape adhesive tape a dh esi ve tap e
Hole position W
1
9.0 p0.5 9.0 p0.5 9.0 p0.5 9.0 p0.5 9.0 p0.5 9.0 p0.5 9.0 p0.5
Hold down tape position W
2
0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max.
Feed hole diameter D
0
4.0 p0.2 4.0 p0.2 4.0 p0.2 4.0 p0.2 4.0 p0.2 4.0 p0.2 4.0 p0.2
Pitch of component P 12.7 p1.0 12.7 p1.0 12.7 p1.0 25.4 p1.0 25.4 p1.0 38.1 p1.5 3
*
8.1 p1.5 or 50.8 p1.5
cumulative pitch cumulative pitch cumulative pitch cumulative pitch cumulative pitch cumulative pitch cumulative pitch
Feed hole pitch P
0
12.7 p0.3 error max. 12.7 p0.3 error max. 12.7 p0.3 error max. 12.7 p0.3 error max. 12.7 p0.3 error max. 12.7 p0.3 error max. 12.7 p0.3 error max.
1.0 mm/20 pitch 1.0 mm/20 pitch 1.0 mm/20 pitch 1.0 mm/20 pitch 1.0 mm/20 pitch 1.0 mm/20 pitch 1.0 mm/20 pitch
Feed hole centre
P
1
5.1 p0.5 3.85 p0.7 2.6 p0.7 7.7 p0.7 5.2 p0.7 7.8 p0.7 5.3 p0.7
to lead
Hole centre to
P
2
6.35 p1.3 6.35 p1.3 6.35 p1.3 12.7 p1.3 12.7 p1.3 19.05 p1.3 19.05 p1.3
component centre
Feed hole centre to bottom
H
v
16.5
p0.3 16.5 p0.3 16.5 p0.5 16.5 p0.5 16.5 p0.5 16.5 p0.5 16.5 p0.5
edge of the component
18.5
p0.5 18.5 p0.5 18.5 p0.5 18.5 p0.5 18.5 p0.5 18.5 p0.5 18.5 p0.5
Feed hole centre to top
H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
H+H
component
< H
1
edge of component 32.25 max. 32.25 max. 24.5 to 31.5 25.0 to 31.5 26.0 to 37.0 30.0 to 43.0 35.0 to 45.0
Lead spacing at
F 2.5
p0.5 5.0
+0.8
7.5 p0.8 10.0 p0.8 15 p0.8 22.5 p0.8 27.5 p0.8
upper edge of carrier tape
–0.2
Lead diameter d 0.4 p0.05 0.5 p0.05
„
0.5 p0.05 or 0.7
–0.05
„
0.5 p0.05 or 0.7
–0.05
0.8
–0.05
0.8
–0.05
„
0.8
–0.05
or 1.0
–0.05
Component alignment Dh p 2.0 max. p 2.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max.
Total tape thickness t 0.7 p0.2 0.7 p0.2 0.7 p0.2 0.7 p0.2 0.7 p0.2 0.7 p0.2 0.7 p0.2
ROLL/AMMO AMMO
Package
v
(see also page 14)
Unit see details page 76.
v
Please give „H“ dimensions and desired packaging type when ordering. Dims in mm.
„
Diameter of leads see General Data. Please clarify customer-specific deviations with the manufacturer.
* PCM 10 and PCM 15 can be crimped to PCM 7.5.
Position of components according to PCM 7.5 (sketch 1). P
0
= 12.7 or 15.0 is possible.
+0.07 +0.07 +0.08 +0.08 +0.08 +0.1
REEL
P 360 max.
B
52 p2 depending on
P 30 p1 58 p2 comp. dimensions
52 p2 54 p2 depending
REEL
P 360 max.
B 58 p2
or REEL
P 500 max.
B 60 p2 on PCM and
P 30 p1
66 p2
P 25 p1
68 p2 component dimensions
P
P
1
P
0
P
2
F
d
P
P
1
H
1
H
P
0
d
P
2
F
t
D
0
W
2
)h
W
0
P
1
P
2
P
0
P
H
1
H
W
1
W
d
F
Diagram 1:
PCM 2.5/5/7.5mm
Diagram 3: PCM 22.5 and 27.5*mm
*PCM 27.5 taping possible with two feed holes between components
Diagram 2: PCM 10/15 mm