User’s Manual AOYUE Intelligent Soldering Station Int9378 PRO Series 909378pro Illustration similar, may vary depending on model Please read and follow the operating instructions and safety information prior to initial operation. Technical changes reserved! Illustrations, functional steps, and technical data may deviate insignificantly due to continuous further developments.
The information contained in this document may alter at any time without prior notice. No part of this document may be copied or otherwise duplicated without prior written consent. All rights reserved. WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes in this operating manual, nor in the diagrams and illustrations shown.
Introduction Thank you for choosing to purchase this quality product. To minimise the risk of injury, we ask you to always take some basic safety precautions when using this product. Please read this operating manual carefully and make sure that you understand it. Keep these operation instructions in a safe place.
Electrical connection The electrical connection is made to an earthed socket 230 V ~ 50 Hz, fuse min. 10 A. Commissioning • • Place the device on a level and solid surface the temperature of which does not exceed 40 ℃. At the operation site, the device must be in a horizontal position to work properly. Connect the device to the power supply.
Max. power consumption (W) 75 Soldering iron Power (W) 60 Temperature range (℃) 200–480 Heating element Ceramic Output voltage (V) 24 • • • • • • • • • • • Controlled by microprocessor Suitable for various tools: tweezer, sculpting tool, soldering tip, etc.
Instructions for use Important: • • • Make sure the device is on a level surface and that all heat-generating components are in their designated holders. All switches must be off. All connections must be made properly.
Commissioning 1. Plug the power cord into the socket on the back of the station. 2. Plug the power cord into an earthed wall outlet. The station is protected against electrostatic discharge and must be earthed for full performance. 3. Make sure that the power switch is off before plugging or unplugging the soldering iron cord. Otherwise, the circuit board may be damaged. 4. Assemble the soldering iron stand as shown. 5. Connect the soldering iron to the 8-pin output on the bottom right of the station. 6.
7. Repeatedly press the Set button until the display shows “SAVE.” Press the Up button to save the value and exit system configuration mode. 8. The tip is now properly calibrated. 9. Saved settings remain saved and in effect unless changed by the user. Quick access setting The system has two adjustable quick access settings. The quick access functions allow the user to easily jump to a previously set temperature. The two most commonly used temperatures must first be stored in the system.
4. To save the adjusted values, press the Set button repeatedly until the display shows “SAVE.” Press the Down button to save the value and exit system configuration mode. System lock setting The system lock function disables the setting of temperature and system configuration. The display shows “SAFE” when the system lock function is on. To unlock the system, press and hold all three buttons simultaneously for more than 15 s. To enable the system lock feature: 1. 2. 3. 4. 5.
4. To save the setting, press the Set button repeatedly until the display shows “SAVE.” Press the Up button to save the value and exit system configuration mode. Note: When the unit is in system configuration mode and you decide not to save the setting just changed to system memory, press the Set button repeatedly until the display reads “CncL” (Cancel). Press the Down button to exit system configuration mode without saving recent changes.
• Solution: The heating element may be damaged. Replace heater or check soldering iron pin wiring. 3rd case: Soldering iron is connected correctly, display shows low temperature readings and then changes to “Err2” Solution: The heating element is damaged. Replace heater or check soldering iron pin wiring. 3rd problem: Soldering iron tip overheated • Description: Soldering iron tip gets too hot. Solution: The digital offset setting could be too high, resulting in an overheat protection case.
Note: Suitable for all AOYUE soldering irons except lead-free composite tips series, induction series, and 938. © by WilTec Wildanger Technik GmbH http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.
Regulations for waste disposal The Waste Electrical and Electronic Equipment Directive (WEEE Directive, 2012/19/EU) of the EU was implemented in the German law related to electrical and electronic equipment and appliances. All WilTec electric devices that fall under the WEEE directive are labelled with the symbol of a crossedout wheeled rubbish bin. This symbol indicates that this electric device must not be disposed of with the domestic waste.
