User’s Manual Kayak Hoist 61447 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Illustrations, functional steps, and technical data may deviate insignificantly due to continuous further developments. Updating the documentation If you have suggestions for improvement or have found any irregularities, please contact us.
The information contained in this document may alter at any time without prior notice. No part of this document may be copied or otherwise duplicated without prior written consent. All rights reserved. WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes in this operating manual, nor in the diagrams and illustrations shown.
Introduction Thank you for choosing to purchase this quality product. To minimise the risk of injury, we ask you to always take some basic safety precautions when using this product. Please read this operating manual carefully and make sure that you understand it. Keep these operation instructions in a safe place. Safety instructions • • • • • • • • • • • • • • • Do not install the kayak hoist over frequented places or places where children could play. When mounted correctly, the hoist can withstand a max.
Figure 1 № Name/description 1 Wall or obstacle 2 Add 12.7 cm or more. 3 183–305 cm 4 Expansion of strap 5 Strap 6 Add 12.7 cm or more. Step 2 Then determine the distance at which you wish the straps to be fixed (possible from approx. 183 to 305 cm). The scope of delivery contains enough rope to mount the hooks of the hoist at a max. distance of 305 cm. Choose the distance suiting your kayak best.
Step 4 Mount the hoist to the mounting plate before installing the mounting plate on the ceiling. Use Fig.-1 measures to determine the position of the front and rear hook as show in Figg. 2 and 3. Use woodscrews (included in delivery) to install the mounting brackets on the mounting plate. Step 5 To mount the pulley, two or three persons are required. Align the centre of the plate and the centre of the installation spot marked on the ceiling.
5 183–305 cm 6 Rope clip Figure 3 № Name/description 1 Wooden beam 2 Drywall 3 Woodscrew 4 Mounting plate 5 183–305 cm 6 Rope clip 7 Woodscrew https://www.XPOtool.
№ Name/description 1 Wooden beam 2 Mounting plate screwed to the beam (not included in the scope of delivery) 3 Drill a ¾″ hole for the rope guide. 4 Distancer rope 5 Rope clip 6 Space-saver for open beams The mounting plate can be fixed on the upper side of the beams. Thus, the kayak can be lifted nearer to the beam to have more headroom.
Figure 8 № Name/description 1 Woodscrew and washer ⅜″ × 4″ (not included) 2 ½″ drywall 3 Mounting plate (not included) 4 Wooden beam 5 Pilot hole 6 Woodscrew ¼″ × 2″ (2 pieces included) 7 Rear view 8 Side view 9 Separate Note! Woodscrews, washers, and the mounting plate are not included in the scope of delivery. Threading the hoist rope 1. 2. 3. 4. 5. 6. 7. 8. After attaching the mounting brackets/mounting plate to the ceiling, the nylon rope must be threaded through the pulley system.
. A. D. B. . B. Figure 9 № Name/description 1 Thread the rope through the holes of the front side of the brake. 2 Use to hole of the underside of the bracket to end the rope. Secure the end of the rope with a knot. 3 Rope 2 4 Use to hole of the underside of the bracket to end the rope. Secure the end of the rope with a knot. 5 Rope 1 Applying the brake To lower the kayak, remove the excess of the rope from the wall clip. To release the brake, pull both ropes down and to the inside.
Attention! Make sure to hold both ropes when releasing the brake. Pulling one rope, the locking mechanism for both ropes is loosened. Tighten the straps around the kayak with the loops to prevent it from slipping. Note that the kayak could slide off through the straps. Use a rope to prevent the straps from sliding apart. Important Note: Reproduction and any commercial use (of parts) of this operating manual, requires a written permission of WilTec Wildanger Technik GmbH. https://www.XPOtool.
