Use & Care Guide

General Description
• An emulsion of water and polyvinyl acetate suitable for joint
assembly, woodworking and cold press laminating applications
• Ideal for cabinetry and furniture applications
• Fluorescent dye added to glow with blacklight for easier viewing
and cleaning of excess adhesive when wet
• Non-toxic, easy clean-up and heat resistant
• Consumer or professional use
• Does NOT require stirring before use
General Use Instructions
• May be applied by squeeze bottle, brush or roller.
• Ensure substrates and adhesive are above 65˚F.
• Best results are achieved between 70˚F and 85˚F.
• Surfaces must be clean and dry.
• Test in an inconspicuous area before use.
Availability
Pints and 1-gallon jugs
Storage/Shelf Life
• DO NOT ALLOW PRODUCT TO FREEZE.
• Close container tightly when not in use and store off the floor in
a well ventilated area.
• Rotate stock.
• Shelf life expires 1 year from manufacture date.
Joint Assembly
Apply a generous amount of adhesive over the area to be bonded,
fit the joints together snugly, and clamp the assembly to stabilize
the bond for 30 minutes or until the adhesive film dries. Machining
is usually possible one hour after assembly.
Clean-up/Disposal
• Clean with hot tap water while adhesive is wet.
• Removal of dried adhesive is very difficult. Use diluted ammonia
to clean dry adhesive.
• Wash water is RCRA non-hazardous.
• Dispose of in accordance with regulations.
Primary Contents
• Vinyl acetate polymer (CAS 9003-20-7)
• Polyvinyl alcohol (CAS 25213-24-5)
• Starch (CAS 9005-84-9)
• Water (CAS 7732-18-5)
GREENGUARD
®
Indoor Air Quality
GREENGUARD Indoor Air Quality Certified Products meet the
following minimum emission requirements:
Category: Adhesives/Sealants
Emission Types Measure
Individual VOCs <0.1 TLV
Formaldehyde <0.05 ppm (<0.06 mg/m
3
)
4-phenylcyclohexane <0.0065 mg/m
3
Styrene <0.07 mg/m
3
Total VOCs <0.05 mg/m
3
Total aldehydes <0.1 ppm
Volatile Organic Compounds (VOC):
The use, supply, sale or offer for sale of this product in certain states
and localities may be prohibited if it exceeds certain VOC limits.
Please check state and local regulations for any prohibitions on the
sale and use of this product.
Safety
• Non-flammable
• Mildly irritating to eyes
• May irritate sensitive skin
• Inhalation may irritate respiratory tract
• See MSDS for more complete information
• 24-hour Chemtrec Emergency: 1-800-424-9300 (US),1-703-527-
3887 (International)
Warranty
Manufacturer and distributor of this product makes no warranties, express
or implied. No warranty of merchantability or fitness for a particular purpose
shall apply. The person using this product (the “user”) is solely responsible
for determining whether this product is appropriate and/or suitable for user’s
purpose and method of application. Limitation and exclusion of remedies and
damages: the exclusive and sole remedy, and the manufacturer and distributor’s
exclusive and sole obligation, for any defect of this product is the refund of the
purchase price of the product. The manufacturer and distributor shall not, under
any circumstances or under any legal theory, be liable to the purchaser or any
other person for special, incidental or consequential damages of any nature,
including without limitation damages to, or loss of use of, property, damages for
loss of profits or revenues or any other damages arising from the purchase or
use of the product. The manufacturer and distributor’s liability will in no event
exceed the purchase price of the product.
Contact
Customer Service: 1-800-433-3222 or [e-mail]
Visit www.wilsonartadhesives.com for information
Color: Yellow
Viscosity: 5000 cps (typical)
Density: 9.8 pounds/gallon
Solids Content: 47.0% ± 2%
pH: 4 - 5.5
VOC Content: < 20 grams/liter (Meth. 24)
VHAP Content: < 0.032 lbs./lbs. solids
Coverage: ~229 ft
2
/gal @ 7 wet mils
Chalking Temperature: 50°F
Use Temperature: 70°F-85°F
*GREENGUARD
®
Certified
*Complies with SCAQMD, Rule 1168
*Complies with the Ozone Transport Commission (OTC)
*Qualifies for LEED
®
-NC & CI EQ Credit 3.2:
Construction Indoor Air Quality Management Plan - Before
Occupancy
*Qualifies for LEED
®
-NC & CI EQ Credit 4.1:
Low Emitting Materials: Adhesives & Sealants
*Qualifies for LEED
®
-NC & CI EQ Credit 4.4:
Laminating adhesives shall contain no added
urea-formaldehyde resins.
*Qualifies for LEED
®
-NC & CI EQ Credit 4.5:
Low Emitting Materials: Furniture and Furnishings
YELLOW WOOD GLUE
FOR JOINT ASSEMBLY
Physical Properties
©2011 Wilsonart International, Inc.
Rev. 03/2012