Manual

Nitrous Pro-Flow, 4700 NE 11
th
St., Ft. Lauderdale, FL 33334 Pro-Flow Part. No. 810100
[phone] www.nitrousproflow.com
1/2008
Page 17
APPENDIX – RECOMMENDED
PARTS AND SUPPLIERS
WIRE
Wire supplied with most nitrous kits and other
automotive accessories is usually un-tinned copper
with a low number of strands. The unprotected copper
in this inexpensive wire quickly oxidizes, especially
when in contact with dissimilar metals on terminals.
The low number of strands limits life in applications
where flexing occurs. We recommend the use of high
quality industrial grade wire with tinned copper strands
and a high strand count.
18-20 AWG sizes can be used for all signal and
low current applications. 16-18 AWG is adequate for
purge solenoid wiring. 14 AWG should be used for high
current fuel and nitrous solenoid wiring. Carol UL grade
1007/1015 wire is available from Digi-Key.
P/N Description
C2040X-100 20 AWG wire (100 foot spool)
C2064X-100 18 AWG wire (100 foot spool)
C2104X-100 16 AWG wire (100 foot spool)
C2105X-100 14 AWG wire (100 foot spool)
Note: replace X with color code B=Black,
W=White, R=Red, G=Green, A=Orange,
Y=Yellow, L=Blue, N=Brown, S=Gray,
V=Violet
WIRE LABELS
To avoid confusion and possible serious
problems, all wires going into terminal blocks must be
uniquely identified, either by wire color or wire labels
(also called markers). Using a single wire color (white
is preferred) along with wire labels is the most cost
effective solution. A Panduit write-on type label
dispenser is available from Digi-Key. Use a fine point
permanent marker to write on these labels.
P/N Description
298-1295 Panduit PLDR-1 label dispenser with
1.00” x 0.38” write-on area
You can also use Avery P/N 15510
weatherproof white labels (1” x 2-5/8”) available at
Office Depot and other office supply stores. Cut these
in half and fold over the wire to make a flag style label.
CRIMP TERMINALS
High quality crimp terminals and a proper
crimping tool are required to make reliable electrical
connections. Crimp terminals commonly sold in
automotive and hardware stores have brittle vinyl
insulation that easily cracks. We recommend the use of
high quality industrial grade nylon insulated crimp
terminals. The following parts are available from Digi-
Key.
P/N Description
A27241 16-20 AWG #10 ring tongue terminal
A27246 16-20 AWG 1/4” ring tongue terminal
A27248 16-20 AWG 3/8” ring tongue terminal
A27262 14-16 AWG 1/4” ring tongue terminal
A27264 14-16 AWG 3/8” ring tongue terminal
A0911 18-22 AWG .110” female quick
disconnect terminal
MNU18-187DFIK 18-22 AWG .187” female quick
disconnect terminal
MNU18-250DFIK 18-22 AWG 1/4” female quick
disconnect terminal
MNU14-250DFIK 14-16 AWG 1/4” female quick
disconnect terminal
A1069 16-22 AWG butt splice
A1080 14-16 AWG butt splice
A1086 10-12 AWG butt splice
SWITCHES
Safety and reliability concerns dictate the use of
rugged industrial quality switches. Low profile rocker
switches are preferred for automotive applications. We
recommend the C&K DM series miniature rocker
switches available from Mouser Electronics. The SPST
version with LED is ideal for use as an arming switch
with status indication. The SPDT momentary version is
ideal as a manual purge switch.
P/N Description
DM54J72S205Q3 SPST with red LED
D105J12S205QA SPDT momentary