User Manual

ManualsBrandsWilson Electronics ManualsElectronicsAmps Bi-Directional Amplifier Direct

AMPS

DIRECT CONNECTION

AMPLIFIER

Part# 811101

FCC ID: PWO824D

IC: 4726A-824D

iDEN

DIRECT CONNECTION

AMPLIFIER

Part# 814001

FCC ID: PWO806D

IC: 4726A-806D

Installation Guide

Wilson Electronics, Inc.

3301 E. Deseret Drive, St. George, Utah 84790

For additional technical support go to

www.wilsonelectronics.com

Phone: 1-866-294-1660 Fax: 1-435-656-2432

DIRECT CONNECTION

Vehicle & Building

The term “IC:” before the radio certification number only signifies

that Industry of Canada technical specifications were met.

Summary of content (8 pages)

PAGE 1
Vehicle & Building DIRECT CONNECTION Installation Guide AMPS DIRECT CONNECTION AMPLIFIER Part# 811101 FCC ID: PWO824D IC: 4726A-824D iDEN DIRECT CONNECTION AMPLIFIER Part# 814001 FCC ID: PWO806D IC: 4726A-806D Wilson Electronics, Inc. 3301 E. Deseret Drive, St. George, Utah 84790 For additional technical support go to www.wilsonelectronics.
PAGE 2
1. PURPOSE OF THE DIRECT CONNECTION AMPLIFIER The Direct Connection with no signal or low 800MHz up to 3 watts 1900MHz frequencies. up to 3 watts. Bi-directional Amplifier improves RF coverage in areas signal strength. Part# 811101 Amplifies the signal on and allows for the full benefit of the outside antenna on Part# 814001 Amplifies the iDEN (Nextel) frequencies 2. PACKAGE CONTENTS 2.1 Bi-directional Direct Connection Amplifier. 2.2 DC plug-in power supply with ON/OFF switch. 2.3 6ft.
PAGE 3
4. AMPLIFIER INSTALLATION (see illustration on pg.4) 4.1 Installing the Wilson Cellular Antenna 4.1.1 See antenna packaging for model specific instructions. 4.2 Installing The Amplifier 4.2.1 Select a suitable location to mount the AMPLIFIER. • In vehicle installation - under the dash or vehicle seat • In building installation - on a wall or ceiling NOTE: Mount the AMPLIFIER away from direct sunlight, excessive heat and/ or moisture. The amplifier needs proper ventilation.
PAGE 4
In-Building Installation �� Mobile Installation �� 4
PAGE 5
. AMPLIFIER SPECIFICATIONS DIRECT CONNECTION AMPLIFIER PHYSICAL SPECIFICATIONS Connectors Dimensions Weight FME-Male 50 Ohms 5.5x4.3x1.4 (inch) or 14.0x10.8x3.5 (cm) 1.32 Pounds or 600G AMPS #811101 AMPLIFIER SPECIFICATIONS Frequency Gain (up/down) 824-849MHz Uplink 869-894MHz Downlink Cell Site Controlled-Max 10/10 Flatness (up/down) (+/- 2dB / +/-2dB) Max RF (up/down) (+35dBm/+15dBm) Noise Figure (down) (3.5dB@881MHz) Isolation Uplink/Downlink 90dB Power Consumption 1.
PAGE 6
. OPTIONAL ACCESSORIES/ANTENNA OPTIONS 6.1 Coax Cable Extensions 50Ω (see chart on pg.7) 6.2 Antenna Options (see chart on pg. 8) 6.3 N-Female To FME-Female Adapter - Adapts 9913 Coax to the 811101/814001 Bi-directional Amplifier. 6.4 Lightning Suppressor (In-Building application) WARNING: Lightning protection is recommended for all In-Building installations. 6.5 Hardwire Power Supply Kit.
PAGE 7
. TECH SUPPORT If you need further assistance with your installation: 1) Call us Toll-Free at 866-294-1660 2) E-mail tech support at tech@wilsonelectronics.com 3) Go to www.wilsonelectronics.com Our Hours of Operation are: 8:00 AM – 4:30 PM (Mountain Time) EXTENSION CABLE CHART (RG 58 - FME connectors / 9913 - N connectors) 951101 5’ Extension Cable RG 58 Low Loss Coax (0.6 db loss) 951102 10’ Extension Cable RG 58 Low Loss Coax (1.2 db loss) 951103 15’ Extension Cable RG 58 Low Loss Coax (1.
PAGE 8
Outside Antenna Options For more options visit www.wilsonelectronics.com �� Pictures Are Not To Scale Not All Outside Antenna Options Are Shown Questions? 1-866-294-1660 www.wilsonelectronics.