Installation Overview
0 Drive Reach Signal Booster ------~--✓ Power Supply
STEP 1: Select Mounting Location & Assemble the Outside Antenna Once you have determined the best location for the Outside Antenna, insert cable through mast(s) then through Side Exit Adapter. Screw together as shown. Different Assembly Options ... . k.,}. /mast . !-"c;}.
Mast STEP 2: Mounting the Outside Antenna +. If th e vehicle does not have built-in mounting points, a Three-way Mount is included that will work on vehicles with mirror rails. For more info on using Spring, see Installation Guide. STEP 3: Mounting the Inside Antenna Identify a place to mount the In-Vehicle Antenna, either on the side of the seat or on the dash and mount. Th e location should be at least 18 inches but no more than 36 inches from where the cellular device will be used.
STEP 4: Booster Location & Connect Cables from Inside ~ . Antenna ~.., Booster Find a location to place the Drive Reach Booster and secure it with provided bracket. Connect cable from Outside Antenna to labeled booster port and connect cable from Inside Antenna to labeled booster port.
Register your Signal Booster now! Complete the two easy steps to register your booster and receive premium customer service, special offers and more! Step 1: Take a photo of your Photoregister Code including the points ((i)). Step 2: Send it in. D Smartphone U.S. only Text photo to 71403 OR Email U.S./CAN weboost@photoregister.com e WEBOOST OR Online register.we boost.com Need help? Visit photoregister.com/help or text HELP to 71403.
• .:: weboost. Installation Guide A Wilson Electronics Brand ,~ .,, .:i weboost ( ) )I,..
Index Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 STEP 1 Select Mounting Location & Assemble the Outside Antenna ................ 2 STEP 2 Mounting the Outside Antenna ......................................... 4 STEP 3 Mounting the Inside Antenna .......................................... 6 STEP 4 Connect Coax Cables to Booster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package Contents I I I I \\ Drive Reach Signal Booster & Bracket Outside Antenna Inside Antenna Power Supply ' 13 in. & 18 in.
STEP 1 Select Mounting Location & Assemble the Outside Antenna Once you have determined the best location for the Outside Antenna, insert cable through Mast Extension(s) then through Side Exit Adapter. Outside Antenna / 13in. mast / 13in. mast run cable . ' / through Mast Extension(s) cable from Outside Antenna run cable through Mast Extension(s) Mast Extension 13 in. mast I• 18 in.
(STEP 1 cont.) Outside Antenna Use Thread Locker (provided) to thread points and screw into place. NOTE: Be sure the Outside Antenna is the correct height before applying Thread Locker. NOTE: When adding the Side Exit Adapter hold the Outside Antenna vertically and screw the adapter from the bottom up. This reduces cable twisting. mast • add Thread Locker ...
STEP 2 Mounting the Outside Antenna Mast Extension If the vehicle does not have built-in mounting points, a 3-Way Mount is included that will work on vehicles with mirror rails. NOTE: The cable is strong enough that it may be shut in most vehicle doors without damaging the cable.
(STEP 2 cont.) Mast Extension If installing with the Spring, disassemble the 3-Way Mount and use disc washer and nut (provided) to mount the Outside Antenna with Spring as shown.
STEP 3 Mounting the Inside Antenna Identify a place to mount the Inside Antenna, either on the side of the seat or on the dash and mount. The location should be at least 18 inches but no more than 36 inches from where the cellular device will be used. Use the Velcro® adhesive strip/adhesive strip provided and attach to desired location.
STEP 4 Connect Coax Cables to Booster Connect the cable from the Outside Antenna to the port labeled "Outside Antenna" on the booster and connect the cable from the Inside Antenna to the port labeled "Inside Antenna" on the booster.
STEP 5 Connect Power Supply to Booster Connect the 12V Power Supply Cord to the end of the Booster, labeled "12V DC" then plug the power adapter into vehicle's 12V DC Power Supply. Push switch to ON position. If your Drive Reach is working correctly, the light on the Booster will be green. Use only the Power Supply provided in this package.
Booster Light Patterns SOLID GREEN This indicates that your Drive Reach Booster is functioning properly and there are no issues with installation. SOLID RED Band has shutoff. This is due to a feedback loop condition called oscillation. This is a built in safety feature that causes a band to shut off to prevent harmful interference with a nearby cell tower. Refer to Troubleshooting section.
(Booster Light Patterns cont.) NOTE: The Signal Booster can be reset by disconnecting and reconnecting the power supply. After troubleshooting you must initiate a new power cycle by disconnecting and then reconnecting power to the Booster.
Troubleshooting FIXING BLINKING OR RED LIGHT ISSUES This section is only applicable if the Booster is red or blinking red and you are not experiencing the desired signal boost. 1 Unplug the Booster's power supply. 2 Relocate the inside and Outside Antenna further from each other. The objective is to increase the separation distance between them, so that they will not create this feedback condition discussed before. 3 Plug Power Supply back in and ensure switch is in ON position.
(Troubleshooting cont.) FREQUENTLY ASKED QUESTIONS How can I contact customer support? Customer Support can be reached Monday through Friday by calling 866.294.1660, or through our support site at support.weboost.com. Why do I need to create distance between the Outside Antenna and Inside Antenna? Antennas connected to a booster create spheres of signal. When these spheres overlap, a condition called oscillation occurs.
Safety Guidelines Use only the power supply provided in this package. Use of a non-weBoost product may damage your equipment. Connecting this signal booster directly to the cell phone with use of an adapter will damage the cell phone. RF Safety Warning: Any antenna used with this device must be located at least 8 inches from all persons. AWS Warning: The Outside Antenna must be installed no higher than 10 meters (31'9") above ground. This is a CONSUMER device.
(Safety Guidelines cont.) FOR MORE INFORMATION ON REGISTERING YOUR SIGNAL BOOSTER WITH YOUR WIRELESS PROVIDER, PLEASE SEE BELOW: T-Mobile/Sprint/MetroPCS: https://www.t-mobile.com/su p port/coverage/register-a-sign aI-booster Verizon Wireless: http://www.verizonwireless.com/wcms/consumer/register-signal-booster.html AT&T: https://securec45.securewebsession.com/attsignalbooster.com/ U.S. Cellular: http://www.uscellular.com/uscellular/support/fcc-booster-registration.
Antenna Info The following accessories are certified by the FCC to be used with the Drive Reach Booster. This radio transmitter 4726A-460061 has been approved by innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Specifications Drive Reach Cell Signal Booster 460061 Model PWO460061 FCC Connectors SMB.Jack Antenna Impedance SO Ohms Frequency 698~716 MHz, 728-756 MHz, m-787 MHz. 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz Power output for single cell phone (Uplink) dBm 700 MH:r 812/17 25.4 700 MHzB13 25.6 800MHzBG 25.6 1700MHz B4 26.7 1900MHz B2 26.9 Power output for single cell phone (Downlink) dBm 4.8 4.8 4.8 4.6 4.
0 2 YEAR WARRANTY weBoost Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase. Signal Boosters may also be returned directly to the manufacturer at the consumer's expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by we Boost. weBoost shall, at its option, either repair or replace the product.
• .:: weboost. A Wilson Electronics Brand f @ YouDm 3301 East Deseret Drive, St. George, UT 6) 866.294.1660 (D www.weboost.com ~ support@weboost.com Copyright © 2020 weBoost. All rights reserved. weBoost products covered by U.S. patent(s) and pending application(s) For patents go to: weboost.com/us/patents NOT AFFILIATED WITH WILSON ANTENNA GDE000368_Rev01_01.08.
• .:: weboost. Here at weBoost, we sincerely hope you'll love the enhanced cellular reception our products have brought to millions of satisfied customers. All of our weBoost products are designed, assembled, and tested in the USA. Many of our competitors are overseas companies and may not take the same pride in their products as we do. To help support our American businesses and workforce, we value honest online reviews.
•• ••• Need help? Contact us directly. G support.weboost.com (;) 866.294.
