• .:: weboost. A WILSON ELECTRONICS BRAND DRIVE SLEEK Vehicle Signal Booster Kit . ··•.. Ive boost User Manual NEED HELP? G support.weboost.com 6) 866.294.
Index Package Contents 1 Jiiijji Mount Outside Antenna 2 li'il' Route & Connect Booster 3 li'i*' Route Cable To Front Of Vehicle 5 Jiijii Connect System To Power ---------------------------------- 6 li'ili Insert Phone Into Cradle 7 Troubleshooting ___ ___ _____ ________ __ _____ _____ _____ ___ ___ __ ___ __ _______ __ 8 Safety G u ide Iin e s ________________________________________________________ 9 Specifications __ ____ ____ __ _________ ___ ____ ___ ____ ____ ___ _____ ___ ____ ___ _
Package Contents Ll~ Sleek Cradle Outside Antenna ~ Signal Booster Power Supply G DRIVE SLEEK CELL PHONE SIGNAL BOOSTER Magnetic Vent Mount (for cradle)
Step 1: Mount Outside Magnetic Antenna Identify a location on the top of your vehicle that is: • Near the center of the roof • At least 12 inches away from any other antennas ·At least 6 inches away from any windows (including sunroofs) =ft (rl )) -.... Clean the surface where you will place the outside antenna. Mount the outside antenna by placing on top of vehicle. 6 in.
Step 2: Route Antenna Cable & Connect Booster Route the cable into the vehicle. See examples below. NOTE: The cable is strong enough that it may be shut in most vehicle doors without damaging the cable. Car/Sedan: Cable routed into rear side door. NOTE: When going through car wash, remember to remove your antenna. SUVNan/Hatchback: Cable routed into top of hatchback door. Truck: Cable routed into side door.
(STEP 2 cont.) Connect the cable from the outside antenna to the booster port labeled L ANTENNA by simply pressing the connector in until you hear a " click". NOTE : Connect ing ca ble from outside antenna to b oo ste r does not take much forc e. ~--------~~- r booste:: ~::::::::::==---------- The included Velcro can be used to mount the booster out-of-the way on the floor under a seat or mounted to the side of the trunk.
Step 3: Route Cable To Front Of Vehicle & Connect To Cradle We recommend routing the 15ft. fixed cable from the booster, under mats and between seats up to the front of the vehicle where the cradle will be located. ve hicle Connect booster cable to cradle cable.
Step 4: Connect System To Power Connect the power to the 12V* CLA port on your vehicle and route power cable back to the booster. NOTE: We recommend routing with the same path as the cradle/booster cable (under mats and between seats). Cable clips are provided to help route & secure the cables. Connect power cable to booster port labeled === . NOTE: The booster will be on whenever there is power from the 12V CLA port.
Step 5: Insert Your Phone Into Cradle Make sure you have plenty of slack in the cable going up to the cradle (VelcroE straps included to manage excess cable). Insert your phone into cradle and watch your signal increase! NOTE: A magnetic vent mount is provided which provides a versatile, safe and functional smartphone solution. IMPORTANT: The FCC requires to never use the cell phone in the cradle next to your ear.
Troubleshooting Solid White (LED on cradle) This indicates that your booster is functioning properly and at maximum gain. Light Off (LED on cradle) Check/secure power connections to the CLA, booster, and cradle. If light shuts off, remove from vehicle port and plug back in to reset the system. For any questions or assistance contact our weBoost Customer Support Team (1-866-294-1660).
Safety Guidelines Use only the power supply provided in this package. Use of a non-weBoost product may damage your equipment. Any antenna used with this device must be located at least 8 inches from all persons. FCC requires to never use the cell phone in the cradle next to your ear. This is a CONSUMER device. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider's consent. Most wireless providers consent to the use of signal boosters.
Specifications Drive Sleek U470035 Product Number 460035 Model Number PW0460035 FCC ID: 4726A-460035 IC: Freque 21.57 800 MHz Band 5 22.65 1700 MHz Band4 25.56 1900 MHz Band 2 19.19 700 MHz 8and13 2.1 800 MHz Band 5 -2.5 2100 MHZ Band4 -0.6 1900 MHz Band 2 Power output for single cell phone (Uplink) dBm 700 MHz: Band12117 18.74 700 MHz Band 13 Power output for single cell phone (Downlink) dBm 700 MHz Band 12/17 2.1 Noise Figure Power Requirements 2.5 SdB nominal 12 V 1.
0 2 YEAR WARRANTY weBoost Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase. Signal Boosters may also be returned directly to the manufacturer at the consumer's expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by wesoost. weBoost shall, at its option, either repair or replace the product.
• .:: weboost. f You ID 3301 East Deseret Drive, St. George, UT 6) 866.294.1660 e www.weboost.com ~ support.weboost.com Copyright© 2017 weBoost. All rights reserved. weBoost products covered by U.S. patent(s) and pending application(s) For patents go to: weboost.com/us/patents NOT AFFILIATED WITH WILSON ANTENNA GDE000009 _Rev02_10.04.
• •• ••• Need help? Contact us directly. G support.weboost.com 0) 866.294.
Adhesive Disk Use to mount the outside antenna to the top of aluminum vehicles (do not use if outside antenna will magnetize to the top of vehicle). To prepare the surface, wipe clean with a damp cloth then dry surface before applying.
Register your signal booster now! Complete the two easy steps to register your booster and receive premium customer service, special offers and more! Step 1 TAKE A PHOTO Take a photo of your Photo register Code including the points{ ® ). Step 2 SEND 0 IT IN SMARTPHONE US Only Text photo to 71403 OR •• EMAIL US/ CAN weboost@photoregister.com OR • ONLINE reg iste r.weboost.com ·:: weboost. · ®- WE BOOST -® Need help? Visit Photoregister.com/help or text HELP to 71403. 104112_ Rev 02 _ 02.25.
