A Wilson Electronics Brand PRO 710i Industrial Class In-Building Cell Signal Amplifier Supporting Band 71 (600MHz) Installation Guide wilsonpro.com 866.294.
Index Package Contents 1 About The Pro 710i 2 Key Features 4 Post Install Setup 5 Menu System 7 Safety Guidelines 11 Warranty 13
Package Contents Kit 460064 Pro 710i PRO 710i INDUSTRIAL CLASS IN-BUILDING CELL SIGNAL AMPLIFIER 1
Pro 710i Industrial Class In-Building Cell Signal Amplifier Supporting Band 71 (600MHz) Up to +25 dBm uplink power and 85 dB gain for maintaining connections with far-away cell towers Up to +25 dBm downlink power for improved indoor cell coverage area eXtended Dynamic Range (XDR) for Continuous Connectivity Color touch screen, for easy installation and displaying detailed amplifier status 2 INDUSTRIAL CLASS IN-BUILDING CELL SIGNAL AMPLIFIER PRO 710i
The Pro 710i industrial class, in-building, cell signal amplifier provides significantly enhanced band 71 (600MHz) signal strength, supporting 4G LTE and 5G technology. The Pro 710i can be installed as either a “stand-alone” amplifier providing exclusive band 71 amplification, or it can be combined with a new or existing WilsonPro amplifier system, supporting multiple bands. Because the Pro 710i is an industrial class amplifier, local band 71 carrier approval must be obatined for every installation.
Key Features Industrial Class Amplification: Up to 100,000 sq. ft. of band 71 (600MHz) coverage with a single amplifier (local carrier approval required for each installation). Extended Dynamic Range (XDR) for continuous connectivity: XDR lets the Pro 710i system work with an incoming signal and never shuts down due to a strong outside signal.
Post Install Setup The Pro 710i is designed with advanced internal programming, which allows it to automatically adjust for a variety of conditions, while still amplifying weak signals. Once the antenna cables are connected, turn the unit on by connecting the power supply cord, at the bottom.
Installation Diagram A Wilson Lightning Surge Protector is recommended for all building installations. Make sure the protector is installed outside the building. Connect it to suitable ground and in line, between the Outside Antenna and the Signal Amplifier. Combined Outside Antennas Band 71, 600 MHz Cell Tower Bands 4/5/12/13/25 Cell Tower Inside Dome Antenna Combiner ENTERPRISE 1300 PRO 710i Pro710i and Enterprise 1300 (Common Mode) combined.
Menu System The Pro 710i takes about 5 seconds to boot up. Once boot up is complete, the home screen will appear, showing the amplification and status of each port and band. Start Up Screen Band Menu Color Description A solid green color indicates that a band is operating correctly with maximum allowable gain. A solid yellow color indicates band gain reduction because of an oscillation condition.
(MENU SYSTEM cont.) A red color indicates a band has been shut down because of a severe oscillation condition or repeated oscillation. Reposition antennas (increase separation between indoor and outdoor antennas, and point in opposite directions) and then reboot (turn the unit off & on) the Pro 710i to reactivate the band and maximize performance. When adequate separation is achieved, the red color will return to green upon reboot.
Settings Screen “Full Gain” is displayed if the there is a weak outside signal requiring the amplifier to operate with maximum allowable gain”. The amplifier is functioning normally; however, a stronger signal might be obtained with some antenna adjustments. “XDR Gain” is displayed , indicating that the amplifier has reduced it’s gain to accommodate a moderate to strong outside signal. The amplifier is functioning normally and no adjustments are needed.
(MENU SYSTEM - SETTINGS SCREEN cont.) Significant oscillation is occurring. Additional separation (isolation) is needed between inside and outside antennas. Severe or repeated oscillations have occurred and amplifier has shut off.
Safety Guidelines Warnings WARNING: Changes or modifications not expressly approved by Wilson Electronics will void the user’s authority to operate the equipment. WARNING: E911 location information may not be provided or may be inaccurate for calls served BY USING THIS DEVICE. To uphold compliance with network protection standards, all active cellular devices must maintain at least 6 feet of separation distance from Panel and Dome antennas. Use only the power supply provided in this package.
Specifications Model Number 460064 FCC ID PWO460064 IC ID 4726A-460064 Connectors N-Female Antenna Impedance 50 Ohms Max Gain 85 dB Frequency 617-652 MHz, 663-698 MHz Power output for single cell phone (Uplink) dBm 600MHz Band 71 Power output for single cell phone (Downlink) dBm 600MHz Band 71 24.2 24.5 Noise Figure 5 dB nominal Isolation > 90 dB Power Requirements 120V AC 0.5A Each Signal Booster is individually tested and factory set to ensure FCC compliance.
Warranty 30 DAY MONEY-BACK GUARANTEE All WilsonPro products are protected by WilsonPro 30-day money-back guarantee. If for any reason the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase. 3 YEAR WARRANTY WilsonPro Amplifiers are warranted for three (3) years against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase.
A Wilson Electronics Brand 3301 East Deseret Drive, St. George, UT www.wilsonpro.com | support.wilsonpro.com Copyright © 2017 2016 Wilson Electronics. All rights reserved. Wilson Electronics products covered by U.S. patent(s) and pending application(s) For patents go to: weboost.com/us/patents NOT AFFILIATED WITH WILSON ANTENNA GDE000257_Rev01_05.11.
