PRO SERIES INSTALLATION GUIDE In-Building Cellular Signal Boosters Contents: How Cellular Boosters Work. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Inside This Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Install Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How a Cellular Booster Improves Indoor Signals Wilson cellular signal booster systems work as follows: an outdoor antenna placed on a building where some cell signal is present, (ideally on a roof or pole), receives and sends that weak signal via coax cable (like used in satellite TV installs) to a signal booster located indoors.
Inside this Package Note: Kits may contain different accessories To purchase Expansion Kits call Wilson Electronics Sales Department at: 888-503-5329 Signal Booster Wide Band Directional Antenna 75’ Wilson 400 Wide Band Panel Antenna 50’ Wilson 400 2’ Wilson 400 Lightning Surge Protector (859992) For additional antenna options see pages 14 & 15. Install Overview Refer to Installation Diagram on page 3 & 4. Contact Wilson Electronics Technical Support Team with any questions at 866-839-9361. 1.
6. Before powering up the signal booster, verify that both the outside antenna and the inside antennas are connected correctly, and check that all connections are tight. Note: Be careful when plugging the connectors in so as not to bend the center pins on the connectors. 7. Power on the signal booster by plugging in the included power supply. If the lights are not green, please refer to pages 9-11.
Selecting a Location for the Outside Antenna Wide Band Antenna Cell Tower The outside antenna must be mounted at a location outside of the home or building, where the strongest cell signal is present. This can be accomplished by using the Wilson Signal Meter. Alternatively, a cell phone in test mode can be used for finding the area around the building with the strongest signal.
Installing Lightning Protection Warning: Lightning protection is recommended for all installations (#859992- 75 Ohm, shown below). Take extreme care to ensure that neither you nor the antenna comes near any electric power lines. Install the Lightning Surge Protector (LSP) outside, in line with the coax cable from the outside antenna, near where the coax cable from the outside antenna will enter the building. Connect the Outside antenna cable to one of the connectors of the surge protector.
Installing the Inside Panel Antenna(s) Select a location for the inside antenna, preferably in the center of where the signal needs to be amplified. A minimum separation distance of 20 vertical feet and or 50 horizontal feet between the inside and outside antenna(s) may be necessary in order to achieve full booster gain and therefore maximum indoor coverage.
Note: Do not install in areas subject to temperatures in excess of 150 °F. Note: Maintain at least 6 inches of clearance from surrounding objects. Be careful when plugging the connector in so as not to damage the center pins on the connectors. Run the outside antenna cable to the signal booster and attach it to the connector labeled “Outside Antenna” on the signal booster. Run the inside antenna cable to the signal booster and attach it to the connector labeled “Inside Antenna” on the signal booster.
About Wilson Electronics Wilson Electronics, LLC has been a leader in the wireless communications industry for over 40 years. The company designs and manufactures Signal Boosters, antennas and related components that significantly improve cellular telephone signal reception and transmission in a wide variety of applications, mobile (marine, RV, vehicles) and in-building (home, office, machine to machine).
Warnings and Recommendations WARNING: T o uphold compliance with network protection standards, all active cellular devices must maintain at least 6 feet of separation distance from Panel and Dome antennas. WARNING: C onnecting the Signal Booster directly to the cell phone with use of an adapter will damage the cell phone. WARNING: U se only the power supply provided in this package. Use of a nonWilson Electronics product may damage your equipment.
Inside Antenna Expansion Kit (contact Wilson Technical Support for assistance) Kit 309900-50N40090 • 2- Wall Panel antennas • 1 - 50 ohm 3-Way Splitter • 1 - 100' Wilson 400 Kit 309905-50N17490 • 3 – Wall Panel Antennas • 3- 2-Way 50 Ohm Splitters • 90' RG174 Kit 309902-75F0650 • 2 - Wall Panel Antennas • 1 - 3-Way 75Ohm Splitter • 50' RG6 Kit 309903-75F1180 • 3 – Wall Panel Antennas • 3 - 2-Way 75Ohm Splitters • 80' RG11 cable Kit 309904-75F5830 • 1 - Wall Panel Antenna • 1 - 2-Way 75 Ohm Splitter • 30' R
Kit 311129-400100 • 800 MHz Yagi Antenna • 100’ LMR400 Cable Kit 314411-40075 • 50 Ohm Wide Band Directional Antenna • 75’ LMR400 Cable Kit 314453-40075 • 50 Ohm Pole Mount Panel Antenna • 75’ LMR400 Cable Kit 304422-40020 • 50 Ohm 4G Omni Antenna • 20' Wilson400 cable Kit 304422-5810 • 50 Ohm 4G Omni Antenna • 10' RG58 cable Kit 304422-1120 • 50 Ohm 4G Omni Antenna • 20' RG11 cable • May need separate adapter 75 Ohm Outside Antenna Kits (contact Wilson Technical Support for assistance) Kit 301111-0675 •
Kit 304424-1120 • 50 Ohm 4G Omni Antenna • 20' RG11 cable • May need separate adapter Mini-Mag Outside Antenna (contact Wilson Technical Support for assistance) 301126 w/12.5 RG174 cable-SMA 30-Day Money-Back Guarantee All Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee. If for any reason the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase.
Notes: _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _________
Notes: _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _________
Signal Booster Specifications WilsonPro Precision 4000R™ Product Number U460031 Model Number 460031 FCC ID PWO460031 IC 4726A-460031 Connectors N-Female Antenna Impedance 50 Ohms Frequency 698-716 MHz, 746-787 MHz, 824-894 MHz, 1850-1990 MHz, 1710-1755/2110-2155 MHz Passband Gain (nominal) 20 dB Bandwidth (MHz) Typical Maximum Power output for single cell phone (Uplink) dBm Power output for single cell phone (Downlink) dBm Power output for multiple received channels (Uplink) dBm No.
