A Wilson Electronics Brand WILSON PRO 1050 In-Building Cellular Signal Booster With In-Line Amplification User Manual NEED HELP? wilsonpro.com 866.294.
_____ Index Package Content 1 About The WilsonPro 1050 System 2 Key Features 4 Competitive Advantages 5 Post Install Setup 7 1050 Main Status Screen 8 1050 In-Line Status Screens 10 Safety Guidelines 12 Warranty 17
________ Package Content Kit 460230 WilsonPro 1050 Two-Part Booster System 100’ Wilson 400 Cable Wide Band Directional Antenna + 75’ Wilson 400 Cable 2’ Wilson 400 Cable Dome Antenna + 100’ Wilson 400 Cable Lightning Surge Protector WILSON PRO 1050 IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION 1
WilsonPro 1050 System FCC Approved In-Line Amplification Compensates for up to 300’ of indoor cable losses using in-line amplification. Onboard Software For Better Control Automatically controlled with onboard software, ensuring great connectivity throughout large spaces and multi-story buildings. Extended Dynamic Range For Continuous Connectivity XDR allows the booster system to never shutdown due to too strong of a signal. No matter how strong, the booster system will never overpower and shutdown.
In-Line Amplification The WilsonPRO 1050 Cellular Signal Booster System automatically compensates for signal loss resulting from a long indoor RF coax cable run. Simply connect the 1050 In-Line unit at a cable length between 100’ and 300’ from the 1050 Main unit. When both units are powered up, they will begin to communicate with each other, sending signals and calculating the amount of signal loss in the cable.
____________ Key Features FCC Approved In-Line Amplification: Compensates for up to 300’ of indoor cable losses using in-line amplification, providing cell coverage to hard-to-reach areas. Onboard Software for Better Control: Booster is automatically controlled with automatic onboard software, ensuring great connectivity throughout large spaces and multi-story buildings. The booster will adjust its gain level up or down as required by the conditions of the immediate signal environment.
___________ Competitive Advantages Highest Downlink Power: Up to +15dB more downlink power than the competition allows for stronger signal in environments where the incoming signal is weak. The benefit is a stronger signal sent to the inside antennas, providing larger coverage area from a single booster. Highest Uplink Power: This allows for a stronger signal transmitted to the tower, up to +3dB more than the competition, providing greater user capacity and increased range from the cell site.
__________ Installation Diagram A Wilson Lightning Surge Protector is recommended for all building installations. Make sure the protector is installed outside the building at point of entry connected to a suitable ground and in line between the Outside Antenna and the Signal Booster.
__________ Post Install Setup Outside Antenna The WilsonPRO 1050 System is designed with advanced internal programming, which allows it to automatically adjust for a variety of conditions, while still boosting weak signals. Lightning Surge Protector Once the AC power cable and antenna cables are connected, turn the unit on by toggling the power switch located near the AC power receptacle.
____________ 1050 Main Status Screen Upon power up, the 1050 MAIN unit will attempt to begin it’s calibration routine, which lasts approximately 14 seconds during which time one of the following messages will appear on the screen: BAND SELECT Boot Screen RESET BAND SELECT BAND SELECT CABLE LOSS RESET RESET BAND SELECT BAND SELECT In-Line Found Screen CABLESELECT LOSS BAND CABLE LOSS RESET BAND SELECT CABLE LOSS RESET RESET The 1050 In-Line unit has been found BAND SELECT RESET CABLE LOSS and
________ RESET CABLE LOSS 1050 Main Status Screen (cont.) BAND SELECT RESET Failed Calibration Screen CABLE LOSS Failed cable loss calibration. Cable loss BAND must be between 4dB and 25dB forSELECT all bands. If the cable loss is calculated to be outside of this range, calibration will fail. This range correspondsRESET between 100 feet and 300 feet of CABLE LOSS Wilson 400 Cable.
____________ 1050 In-Line Status Lights The 1050 In-Line has 3 status lights: 1050 In-Line CABLE CAL COM STATUS 1050 In-Line CABLE CAL COM STATUS ‘STATUS’ LED: GREEN: Normal 1050 In-Line CABLE CAL COM STATUS 1050 In-Line RED: One or more bands has shut off due to OSCILLATION.
BLE CAL ________ 1050 In-LIne Status Screen (cont.) 1050 In-Line CABLE CAL COM STATUS 1050 In-Line CABLE CAL COM STATUS ‘COM’ LED: GREEN: Normal, waiting for next communications event 1050 In-Line CABLE CAL COM STATUS ORANGE: Brief orange blink when 1050 In-Linewith 1050 Main. communicating 1050 In-Line COM STATUS CABLE CAL COM STATUS RED: Communications failure when attempting to communicate with 1050 Main. ‘CABLE CAL’ LED: GREEN: Calibration complete.
______________ Safety Guidelines Warnings o uphold compliance with network protection standards, all active cellular devices must maintain at T least 6 feet of separation distance from Panel and Dome antennas. Use only the power supply provided in this package. Use of a non-Wilson Electronics product may damage your equipment. The Signal Booster unit is designed for use in an indoor, temperature-controlled environment (less than 100 degrees Fahrenheit).
_________________ Antenna Kit Options The following accessories are certified by the FCC to be used with the Wilson PRO 1050 System. In-Line Box-To-Box Expansion Kit* Kit 952300-1N 1 - 100’ Wilson 400 Cable 1 - N-Female to N-Female Connector Kit 952300-2N 2 - 100’ Wilson 400 Cable 2- N-Female to N-Female Connector * Only Wilson Kit 952300-1N / Kit 952300-2N are authorized for extension of 200ft and 300ft total length on box-to-box connection.
___________ Specifications Product Number 460030 Model Number 460030 FCC ID PWO460030 / PWO0460030IL IC ID 4726A-460030 Connectors N-Female Antenna Impedance 50 Ohms 698-716 MHz, 729-746 MHz, 746-756 MHz, 777-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz Frequency Power output for single cell phone (Uplink) dBm Power output for single cell phone (Downlink) dBm Noise Figure Isolation Power Requirements 700MHz Band12/17 700MHz Band13 800MHz 1700MHz 24.7 24.7 24.4 25.1 24.
____________ Notes WILSON PRO 1050 IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION 15
____________ Notes 16 IN-BUILDING SIGNAL BOOSTER WITH IN-LINE AMPLIFICATION WILSON PRO 1050
________ Warranty 30 DAY MONEY-BACK GUARANTEE All WilsonPro products are protected by WilsonPro 30-day money-back guarantee. If for any reason the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase. 3 YEAR WARRANTY WilsonPro Boosters are warranted for three (3) years against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase.
A Wilson Electronics Brand A Wilson Electronics Brand 3301 East Deseret Drive, St. George, UT www.wilsonpro.com | support.wilsonpro.com Copyright © 2017 Wilson Electronics. All rights reserved. Wilson Electronics products covered by U.S. patent(s) and pending application(s) For patents go to: weboost.com/us/patents NOT AFFILIATED WITH WILSON ANTENNA 111853_RevFCC_09.01.
