PRO SERIES INSTALLATION GUIDE PRO 70 PLUS™-50 Ohm In-Building SmarTech ® Cellular Signal Boosters Contents: How Cellular Boosters Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Inside This Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Install Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How a Cellular Booster Improves Indoor Signals Wilson cellular signal booster systems work as follows: an outdoor antenna placed on a building where some cell signal is present, (ideally on a roof or pole), receives and sends that weak signal via coax cable (like used in satellite TV installs) to a signal booster located indoors.
Inside this Package Note: Kits may contain different accessories To purchase Expansion Kits call Wilson Electronics Sales Department at: 888-503-5329 Signal Booster Wide Band Directional Antenna 75’ LMR400 Cable (314411-40075) AC/DC Lightning Surge Wide Band Panel Antenna 2’ LMR400 Cable Power Supply (952302) Protector 60’ LMR400 Cable 12V/3A (859900) (859902) (311135-40060) For additional antenna options see pages 14 & 15. Install Overview Refer to Installation Diagram on page 3 & 4.
Installation Diagram Outside Antenna (Wide Band Directional (W Antenna shown) An Spacing Critical Note: A Wilson Lightning Surge Protector (859902) is recommended for all building installations. Make sure the protector is installed outside the building at point of entry connected to a suitable ground and in line between the Outside Antenna and the Signal Booster. Inside Antenna Inside Antenna Preferred Method: Place the Inside Antenna in the ceiling facing down for the best coverage.
Optional Splitter 2-way or 3-way, when using multiple inside antennas for increased coverage Optional Inside Antenna for added coverage Signal Booster Contact Wilson Electronics Customer Support Team with any questions at 866-839-9361 866 839 9361 or email: il ttech@wilsonelectronics.
Selecting a Location for the Outside Antenna Wide Band Antenna Cell Tower The outside antenna must be mounted at a location outside of the home or building, where the strongest cell signal is present. This can be accomplished by using the Wilson Signal Meter. Alternatively, a cell phone in test mode can be used for finding the area around the building with the strongest signal.
Installing Lightning Protection Warning: Lightning protection is recommended for all installations (#85990250 Ohm, shown below). Take extreme care to ensure that neither you nor the antenna comes near any electric power lines. Install the Lightning Surge Protector (LSP) outside, in line with the coax cable from the outside antenna, near where the coax cable from the outside antenna will enter the building. Connect the Outside antenna cable to one of the connectors of the surge protector.
Installing the Inside Panel Antenna(s) Select a location for the inside antenna, preferably in the center of where the signal needs to be amplified. A minimum separation distance of 20 vertical feet and or 50 horizontal feet between the inside and outside antenna(s) may be necessary in order to achieve full booster gain and therefore maximum indoor coverage.
Note: Do not install in areas subject to temperatures in excess of 150 °F. Note: Maintain at least 6 inches of clearance from surrounding objects. Be careful when plugging the connector in so as not to damage the center pins on the connectors. Run the outside antenna cable to the signal booster and attach it to the connector labeled “Outside Antenna” on the signal booster. Run the inside antenna cable to the signal booster and attach it to the connector labeled “Inside Antenna” on the signal booster.
Post Install Setup The Pro Series booster is designed with advanced internal programming which allows it to automatically adjust itself for a variety of conditions and still boost weak signals. After completing the amplifier installation, the LCD display and push button on the lower panel of the Pro Series booster is used to verify the final gain that the booster adjusted itself to produce after antennas have been placed.
The 800 MHz Band – Cell Band OK The 1900 MHz – PCS Band OK 1700/2100 MHz – AWS Band OK The single “BAND SELECT” button is used to scroll the display through the four cellular bands in order to verify that each band is functioning properly. An asterisk (located next to the band selected) will flash if one or more bands have been turned down/off by the boosters control circuitry due to strong nearby cell site signal overload (“OVL”) and/or oscillation detection (“OSC”) from antennas being too close.
Fixing Red Light Issues If the power light is red: 1. Make sure all connections are tight. 2. You need to increase the distance between the outside antenna and the inside antenna by moving them horizontally and/or vertically farther apart. After doing so, reset the booster by unplugging the power supply and then plugging it back in. If the light is green after separating the antennas, you have eliminated the problem. 3.
About Wilson Electronics Wilson Electronics, LLC has been a leader in the wireless communications industry for over 40 years. The company designs and manufactures Signal Boosters, antennas and related components that significantly improve cellular telephone signal reception and transmission in a wide variety of applications, mobile (marine, RV, vehicles) and in-building (home, office, machine to machine).
Warnings and Recommendations WARNING: To uphold compliance with network protection standards, all active cellular devices must maintain at least 6 feet of separation distance from Panel and Dome antennas. WARNING: Connecting the Signal Booster directly to the cell phone with use of an adapter will damage the cell phone. WARNING: Use only the power supply provided in this package. Use of a nonWilson Electronics product may damage your equipment.
Inside Antenna Expansion Kit (contact Wilson Technical Support for assistance) Kit 309900-50N • 2 - Wall Panel antennas • 1 - 50 ohm 3-Way Splitter Kit 309905-50N • 3 - Wall Panel Antennas • 3 - 2-Way 50 Ohm Splitters Kit 309902-75F • 2 - Wall Panel Antennas • 1 - 3-Way 75Ohm Splitter Kit 309903-75F • 3 - Wall Panel Antennas • 3 - 2-Way 75Ohm Splitters Kit 309904-75F • 1 - Wall Panel Antenna • 1 - 2-Way 75 Ohm Splitter Inside Antenna Kits (contact Wilson Technical Support for assistance) Kit 311155-0630 •
Kit 314473-0640 • 75 Ohm Pole Mount Panel Antenna • 40’ RG6 Cable Kit 311141-0620 • 75 Ohm Grey Brick Antenna • 20’ RG6 Cable Kit 301111-11140 • Yagi Directional Antenna • 140’ RG11 Cable • N-Male to F-Female adapter Kit 311201-1120 • Omni Directional w/ F-Female • 20’ RG11 Cable Kit 311129-11110 • 800 MHz Yagi Directional • 110’ RG11 Cable • N-Male to F-Female adapter Kit 311124-1180 • 1900 MHz Yagi Directional • 80’ RG11 Cable • N-Male to F-Female adapter 15 Kit 314473-1175 • 75 Ohm Pole Mount Panel Ant
30-Day Money-Back Guarantee All Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee. If for any reason the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase. 3-Year Warranty Wilson Electronics Signal Boosters are warranted for three (3) years against defects in workmanship and/or materials.
Notes: _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _________
Notes: _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _________
Signal Booster Specifications Pro 70 Plus™-50 Ohm Model Number U463027 FCC ID PWO460027 IC ID 4726A-460027 Connectors N-Female Antenna Impedance 50 Ohms Frequency 698-716 MHz, 746-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz 700MHz Band12/17 56.0 700MHz Band13 55.2 800MHz 58.9 1700/2100MHz 60.7 1900MHz 60.7 700MHz Band12/17 700MHz Band13 800MHz 1700/2100MHz 1900MHz 29.9 34.4 28.6 34.4 38.7 40.3 82.6 85.0 81.8 85.
