DB Pro™ Cellular Signal Booster 462005/462205 with Directional Antenna Need help? www.WilsonElectronics.com Tech Support 866-294-1660 Mon.- Fri.
IT IS VERY IMPORTANT TO POWER YOUR SIGNAL BOOSTER USING A SURGE PROTECTED AC POWER STRIP WITH AT LEAST A 1000 JOULE RATING. ! FAILURE TO DO THIS WILL VOID YOUR WARRANTY IN THE EVENT OF A POWER SURGE OR LIGHTNING STRIKE. THE SIGNAL BOOSTER UNIT IS DESIGNED FOR USE IN AN INDOOR, TEMPERATURECONTROLLED ENVIRONMENT (LESS THAN 150 DEGREES FAHRENHEIT). IT IS NOT INTENDED FOR USE IN ATTICS OR SIMILAR LOCATIONS SUBJECT TO TEMPERATURES IN EXCESS OF 150°F.
Package Contents AC Power Supply 6V / 2.5A DBPro (Not included with some models) (859912) Pole Mount Bracket Outside Antenna Kit 75 Ohm Wide Band Antenna 30’ RG6 coax cable (314475-0630) Panel Antenna Kit Inside Panel Antenna 30’ RG6 coax cable (311155-0630) Wall Mount Bracket Tools Required for Installation: (depending on your particular installation, you will need the following tools) 1. Pole mount - 10 mm open-end wrench or adjustable wrench 2.
the bar indicator. Go to www. wilsonelectronics.com/test-modeinstructions for help in finding the test mode for your phone. 3. b. The person on the roof should turn the Outside Antenna 45 degrees at a time. Allow 30 seconds for the phone to register with each turn. Acceptable method: Check the bar indicator on your cell phone display and note where the signal appears the strongest. (Note: cell phone bars are only an approximation of signal strength and vary from phone to phone.
3. Be sure the Inside Antenna is NOT facing toward the Outside Antenna. This creates potential oscillation or feedback and reduces the effectiveness of the DB Pro. 4. If you do not know how to mount hardware or run coax cable through walls, ceilings and floors, get help from a Wilson Certified Installer at www.wilsonelectronics.com/wci or from a qualified contractor or electrician. 4.
Signal Booster Installation 1. Select a location for the Signal Booster that is away from excessive heat, direct sunlight, moisture and well ventilated. The enclosure must NOT be air tight. Also, be sure the location is near a power source. 2. Connect the coax cables to the Signal Booster from the Outside Antenna and Inside Antenna at the designated ports. 3. Face inside antenna away from the outside antenna. Inside Antenna 4. 3.
Troubleshooting & Understanding Lights 3. If the coverage area is not large enough with a reduced gain, you need to increase the distance between the Outside Antenna and the Inside Antenna by moving them horizontally and/or vertically farther apart. If the light is green after separating the antennas, increase the gain until the red light comes on. Then slightly decrease the gain until the green light appears. This ensures maximum coverage. 4.
a) Turn away Outside Antenna from the cell tower until lights no longer flash. Contact Wilson Electronics Technical Support Team for assistance. Fixing Blinking Red Light Issues If one or more of the lights on Signal Booster are blinking red, this means that the Signal Booster has shutoff. a) Increase the distance between the cellular device and the Inside Antenna.
Kit 301151-0610 • 75 Ohm Dome Antenna • 10’ RG6 Cable Kit 311135-5820 • 50 Ohm Wall mount Panel Antenna • 20’ RG58 Cable Kit 311155-40060 • 50 Ohm Wall Mount Panel Antenna • 60’ LMR400 Cable Kit 301151-1110 • 75 Ohm Dome Antenna • 10’ RG11 cable Kit 311155-1150 • 75 Ohm Wall mount Panel Antenna • 50’ RG11 Cable Kit 301213 • Desktop Antenna w/ 5’ RG174 50 Ohm Outside Antenna Kits Kit 314453-5825 • 50 Ohm Pole Mount Panel Antenna • 25’ RG58 Cable Kit 314411-5825 • 50 Ohm Wide Band Directional • 25’ RG58 Cabl
Safety Guidelines WARNING: To uphold compliance with network protection standards, all active cellular devices must maintain at least 6 feet of separation distance from Panel and Dome antennas and 4 feet of separation distance from desktop antennas. WARNING: Connecting the Signal Booster directly to the cell phone with use of an adapter will damage the cell phone. WARNING: Use only the power supply provided in this package. Use of a non-Wilson Electronics product may damage your equipment.
Signal Booster Specifications SIGNALBOOST™ DT™ Specifications Model Number 460005 Outside antenna connectors F-Female Outside antenna impedance 75 Ohms Inside antenna connectors F-Female Inside antenna impedance 75 Ohms Dimensions 6.5 x 4.25 x 1.75 inch (16.5 x 10.7 x 4.4 cm) Weight 0.47 lbs (0.213 kg) Frequency 824-894 MHz / 1850-1990 MHz Power output 800 MHz 1900 MHz Power output for single cell phone (uplink) dBm 24.9 22.5 Power output for single received channel (downlink) dBm -2.
30-Day Money-Back Guarantee All Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee. If for any reason the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase. 2-Year Warranty Wilson Electronics Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials.
