User's Manual

ManualsBrandsWilson Electronics ManualsElectronicsModel 460004 Signal Booster

Contents:

Kit Configurations ...............................................1

Antenna Kit Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Installation Diagram ..............................................3

Before Getting Started ............................................4

Quick Install Overview ............................................5

Installing the Outside Antenna ......................................6

Finding the Strongest Signal .......................................7

Installing the Inside Antenna .......................................9

Installing a Wilson Electronics Signal Booster. . . . . . . . . . . . . . . . . . . . . . . . . .9

Powering up a Wilson Electronics Signal Booster ......................10

Understanding the Signal Booster Lights ............................11

Warnings and Recommendations ..................................13

Guarantee & Warranty ...........................................14

Specifications ......................................... Back Cover

Note: This manual contains important safety and operating information. Please read and follow the instructions

in this manual. Failure to do so could be hazardous and result in damage to your Signal Booster.

AG Pro Quint

Appearance of device and accessories may vary.

700 / 800 / AWS (1700 / 2100) / 1900 MHz

In-Building Wireless

Smart Technology ™

Signal Booster

Summary of content (16 pages)

PAGE 1
AG Pro Quint 700 / 800 / AWS (1700 / 2100) / 1900 MHz In-Building Wireless Smart Technology ™ Signal Booster Contents: Kit Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Antenna Kit Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Installation Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 2
Installation Instructions for the Following Wilson Electronics Signal Boosters: AG Pro™ Quint 700 / 800 / AWS (1700 / 2100) / 1900 MHz In-Building Wireless Smart Technology ™ Signal Booster Model # 460004 FCC ID: PWO460004 How it Works Designed to provide signal coverage in buildings up to 80,000 square feet, the Wilson AG Pro Quint boosts signals on 800 MHz, 1900MHz, AWS and both AT&T and Verizon 700 MHz 4G networks as well as Sprint 4G on the G-Block of 1900 MHz.
PAGE 3
Outside Antenna Options Kit 301111-0675 • Yagi Directional Antenna • 75’ RG6 Cable • N-Male to F-Female adapter Kit 311201-0620 • Omni Directional w/ F-Female • 20’ RG6 Cable Kit 311124-0660 • 1900 MHz Yagi Directional • 60’ RG6 Cable • N-Male to F-Female adapter Kit 311129-0650 • 800 MHz Yagi Directional • 50’ RG6 Cable • N-Male to F-Female adapter Kit 314473 -0640 • 75 Ohm Pole Mount Panel Antenna • 40’ RG6 Cable Kit 314475 – 0630 • 75 Ohm Wide Band Directional • 30’ RG6 Cable Kit 311141 - 0620 • 75 Ohm
PAGE 4
Installation Diagram Outside Antenna (Wide Band Directional Antenna shown) Inside Antenna Preferred Method: Place the Inside Antenna in the ceiling facing down for the best coverage. Note: The Inside Antenna may be mounted on the wall directly under the Outside Antenna, in the null zone, if 20 feet of vertical separation can be maintained. Inside Antenna Null Zone: The area under the Outside Antenna, where the Outside Antenna radiates the least.
PAGE 5
Before Getting Started This guide will help you properly install your Wilson Electronics Signal Booster. It is important to read through all of the installation steps for your particular application prior to installing any equipment. Read through the instructions, visualize where all the equipment will need to be installed and do a soft installation before mounting any equipment. Contact Wilson Electronics Technical Support with any questions at: 866-294-1660.
PAGE 6
Quick Install Overview See Installation Diagram on page 3. Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 Mon. - Fri. hours: 7am to 6pm MST. 1. Select a location to install the Signal Booster that is away from excessive heat, direct sunlight, moisture and has proper ventilation. Do not place the Signal Booster in an air-tight enclosure. 2. Select a location on the roof of the building to install the Outside Antenna.
PAGE 7
Reasons for Weak Cellular Signals Anyone who uses a cell phone or cellular data card knows the frustration of not being able to connect to or maintain a strong cellular signal. When this occurs, it is generally due to one of two reasons: 1.
PAGE 8
Warning: Lightning protection is recommended for all installations (sold separately #859902-50 Ohm). Take extreme care to ensure that neither you nor the antenna comes near any electric power lines. Installing Lightning Protection (sold separately) Install the Lightning Surge Protector (LSP) close to the Signal Booster.
PAGE 9
signal strength from the cell tower. It is preferable to have the phone in the test mode so the actual signal strength can be read, as bars are not the most accurate. Go to www.WilsonElectronics.com for help in finding the test mode for your phone. Always make sure the person inside the building gives the signal time to arrive and register on the phone (between 10-30 seconds for phone to reset to the signal reading).
PAGE 10
After drilling the required hole, run the cable through and seal it with cable bushings, silicone or other waterproof sealant to enclose the hole that you have created. In some instances, it may be possible to run the cable up into the fascia of the attic overhang. In this circumstance, the cable will be accessible in the attic for further routing. Installing the Inside Antenna Select a location for the Inside Antenna, preferably in the center of where the signal needs to be amplified.
PAGE 11
Powering up a Wilson Electronics Signal Booster 1. Never point the front of a Directional Outside Antenna toward the Inside Antenna. Refer to Figures 1 & 2 below. 2. Ensure that both the Outside Antenna cable and the Inside Antenna cable are connected to the splitter and the Signal Booster and the connections are tight before powering up the Signal Booster. 3.
PAGE 12
Lights and Troubleshooting for all In-Building Adjustable Signal Boosters The Signal Booster is equipped with four indicator lights for each Band, 700 (Bands 12/17,13), 800 (Band 5), 1900 (Band 2), 1700/2100 (Band 4). The lights will do one of the following 6 things: 1. Green If the indicator lights on the Signal Booster are green, the unit is powered up and working properly. 2. Orange The Signal Booster is experiencing receiver overload.
PAGE 13
the green light appears, waiting one minute in between increments or resetting the Signal Booster by unplugging and plugging it back in. If after separating the antennas your coverage area is still too small, contact Wilson Electronics Technical Support Team for assistance. 4. Blinking Orange & Red If one or more of the lights on the Signal Booster are blinking orange and red, this indicates that the Signal Booster is experiencing extreme receiver overload and has shutoff.
PAGE 14
Warnings and Recommendations Warning: The Directional Antenna must always be located so the back or side points to the Inside Antenna. Never point the front of the Outside Antenna toward the Inside Antenna – this is to prevent oscillation. Warning: Connecting the Signal Booster directly to the cell phone with use of an adapter will damage the cell phone. Warning: Use only the power supply provided. Use of a non-Wilson Electronics product may damage your equipment.
PAGE 15
30-Day Money-Back Guarantee All Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee. If for any reason the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase. 2-Year Warranty Wilson Electronics Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials.
PAGE 16
Signal Booster Specifications AG Pro Quint Model Number 460004 Antenna connectors N-Female Antenna Impedance 50 Ohms Dimensions 8.875 x 6.0 x 1.5 inch (22.5 x 15.2 x 3.8 cm) Weight 2.8 lbs (1.270 kg) Frequency 3 698-746 MHz, 746-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz Power output for single cell phone (dBm) Uplink Downlink Noise Figure (typical downlink/uplink) Isolation 700 MHz Band 17 700 MHz Band 13 23.2 -0.4 23.8 -2.1 800 MHz 1900 MHz 1700/2100 MHz 25.2 -2.