User's Manual

7
#110856_Sleek4G-C_REV07_09.11.12
3301 East Deseret Drive, St. George, UT 84790
For additional Technical Support visit www.WilsonElectronics.com
or email at: [e-mail]
Phone: [phone] Local: 435-673-5021 Fax: [phone]
www.twitter.com/WilsonCellular www.facebook.com/WilsonCellular
Signal Booster Specications
Sleek 4G-C
Model Number 2B2725
Connectors SMA Female
Impedance (input/output) 50 ohms
Frequency 1710-1755 MHz & 2110-2155 MHz / 824-894 MHz / 1850-1990 MHz
1
Passband Gain (nominal)
1700 / 2100 MHz
Typical / Maximum
800 MHz
Typical / Maximum
1900 MHz
Typical / Maximum
Uplink 19 dB / 21 dB 21 dB / 23 dB 20 dB / 23 dB
Downlink 21 dB / 23 dB 19 dB / 22 dB 21 dB / 24 dB
2
20 dB Bandwidth (nominal) 1700 / 2100 MHz 800 MHz 1900 MHz
46 MHz / 50 MHz 26 MHz / 28 MHz 61 MHz / 67 MHz
Power output for single cell phone
(uplink) dBm
1700 / 2100 MHz 800 MHz 1900 MHz
CDMA 26.5 29.2 28.2
EVDO 26.3 29.1 28.1
HSPA 23.2 28.4 26.2
LTE 23.6 27.7 26.8
GSM 26.3 29.1 28.6
EDGE 26.1 28.8 28.1
Power output for single cell phone (dowlink)
dBm
1700 / 2100 MHz 800 MHz 1900 MHz
CDMA -9.1 -9.7 -7.0
EVDO -8.6 -9.6 -7.8
HSPA -6.4 -9.5 -9.0
LTE -7.4 -9.8 -8.8
GSM -9.3 -9.2 -9.3
EDGE -8.7 -9.2 -9.5
3,4
Power output for multiple
received signals (uplink) dBm
The maximum power is reduced by
the number of signals:
Number of
signals
Maximum Power
3
1700 / 2100 MHz 800 MHz 1900 MHz
2 24.2 25.1 21.1
3 20.6 21.6 17.6
4 18.1 13.1 15.1
5 16.2 17.2 13.2
6 14.6 15.6 11.6
3,4
Power output for multiple
received signals (downlink) dBm
The maximum power is reduced by
the number of signals:
Number of
signals
Maximum Power
3
1700 / 2100 MHz 800 MHz 1900 MHz
2 -12.1 -10.4 -10.4
3 -15.6 -13.9 -13.9
4 -18.1 -16.4 -16.4
5 -20.1 -18.3 -18.3
6 -21.6 -19.9 -19.9
Noise Figure (nominal) 3 dB nominal
Isolation > 40 dB
Power Requirements 5.5V DC, 1A
Notes:
1. Nominal gain is the maximum gain at any frequency in the passband.
2. Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplication is 20 dB lower than the passband amplication. One
of the frequencies is lower than the passband and the other is higher.
3. The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the rating would have to be
reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users. This power reduction is to be by means of input
power or gain reduction and not by an attenuator at the output of the device.
4. The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals is doubled.