User's Manual

30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson Electronic’s 30-day money-back guarantee. If
for any reason the performance of any product is not acceptable, simply return the product directly to the
reseller with a dated proof of purchase.
1-Year Warranty
Wilson Electronics signal boosters are warranted for one (1) year against defects in workmanship and/
or materials. Warranty cases may be resolved by returning the product directly to the reseller with a
dated proof of purchase.
Signal boosters may also be returned directly to the manufacturer at the consumer’s expense, with
a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by Wilson
Electronics. Wilson Electronics shall, at its option, either repair or replace the product. Wilson Electronics
will pay for delivery of the repaired or replaced product back to the original consumer if located within
the continental U.S.
This warranty does not apply to any signal boosters determined by Wilson Electronics to have been
subjected to misuse, abuse, neglect, or mishandling that alters or damages physical or electronic
properties.
RMA numbers may be obtained by phoning Technical Support at 866-294-1660.
AIG #110867 (811225) - Rev1 - 022511
3301 East Deseret Drive, St. George, UT 84790
For additional Technical Support visit www.WilsonElectronics.com
or email at: [e-mail]
Phone: [phone] Local: 435-673-5021 Fax: [phone]
www.twitter.com/WilsonCellular www.facebook.com/WilsonCellular
Signal Booster Specifications
Dual Band
800/1900 MHz Specifications
Model Number / Part Number 2B1225 Connectors SMA Female Impedance (input/output) 50 ohms Dimensions
with mounting plate 3.9 x 3.1 x 0.95 in
without mounting plate 3.9 x 1.9 x .085 in
Frequency 824-894 MHz / 1850-1990 MHz 1
Passband Gain (nominal)
Factory set: 5 dB minimum to 20 dB maximum
2
20 dB Bandwidth (nominal)
800 MHz 30 MHz
1900 MHz 68 MHz
Power output for single cell phone (uplink) 800 MHz 1900 MHz
CDMA 30.0 dBm 32.7 dBm
GSM 29.4 dBm 29.0 dBm
EDGE 28.3 dBm 28.9 dBm
WCDMA 31.5 dBm 32.4 dBm
Power output for single received channel (downlink) 800 MHz 1900 MHz
CDMA -3.2 dBm 1.5 dBm
GSM -2.4 dBm -1.5 dBm
EDGE -3.3 dBm -1.5 dBm
WCDMA -3.8 dBm -2.0 dBm
3,4
Power output for multiple
received channels (downlink). The maximum power is reduced by the number of channels:
Number of
channels
Maximum Power
3
800 MHz 1900 MHz
2 -10.9 dBm -5.2 dBm 3 -14.4 dBm -8.8 dBm 4 -16.9 dBm -11.3 dBm 5 -18.9 dBm -13.2 dBm 6 -20.5 dBm -14.8 dBm
Noise Figure (typical) 3 dB nominal Isolation > 60 dB Power Requirements 5V DC, 1A
Notes: 1. Nominal gain is the maximum gain at any frequency in the passband. 2. Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplification is 20 dB
lower than the passband amplification. One of the frequencies is lower than the passband and the other is higher.
3. The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier
signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device.
4. The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals is doubled.