Assembly & Installation Instructions

ManualsBrandsWilliston Forge ManualsCeiling LightsHaag 2-Light Kitchen Island Pendant

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. READ AND SAVE THESE INSTRUCTIONS.

For Pendant Hardware Package (included):

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

Turn off the power at fuse or circuit box

Mounting Strap (A) Fixture Mounting

Screw(D)

Wire Connector (C)

For Pendant Installation Steps

Lock Nut (F)

Canopy Cover Assembly

Ball Nut (G)

Upper Rod

Threaded Pipe

Middle Rod

Lower Rod

Socket

Glass Shade

Outlet Box

House Ground Wire

Wire Connector(C)

Fixture Mounting Screw (D)

Mounting Strap(A)

Green Ground Screw(E)

Lock Nut(F)

Mounting Screw(B)

1. Thread two fixture mounting screws through the mounting strap,

and then secure with two lock nuts. Adjust the length of the fixture

mounting screws if necessary.

2. Attach the mounting strap to the outlet box by using two mounting

screws.

3. Rod Connections:

a. Thread the fixture wire from the fixture through the lower rod, and

then secure the lower rod onto fixture using the threaded pipe.

b. Thread the fixture wire through the middle rod, and then secure

the middle rod onto the lower rod using the threaded pipe.

c. Thread the fixture wire through the upper rod, and

then secure the upper rod onto the middle rod using

the threaded pipe.

d. Thread the fixture wire through the canopy cover

assembly, and then secure the canopy cover assembly

onto the upper rod using the threaded pipe.

Note: Length adjustable from 29" to 89". Use fewer rods if

shorter length is desired.

4. Connecting the wires with wire connectors as follows:

---Connect the black wire from the fixture to the black wire

from the power source.

---Connect the white wire from the fixture to the white wire

from the power source.

---Attach the fixture ground wire (usually green insulation

or bare wire) to the mounting plate with the green

ground screw. Then connect it to the house ground wire

with the wire Connector.

5. Attach the canopy cover assembly to the mounting strap by inserting the

fixture mounting screws, and then secure it with two ball nuts.

Green Ground

Screw (E)

Mounting Screw (B)

Main Fixture

Set Screw

Cord

Vintage Bulb

MAX 60W

(Included)

Glass Holder

Summary of content (4 pages)

PAGE 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS.
PAGE 2
6. Reel out the cord carefully from the main fixture to Adjust the length of cord you need. 7. Install 2 x 60W max medium base vintage bulbs (included) to the sockets. Fig. 1 Support Brace Outlet Box 8. Unscrew three set screws from the glass holder. Hold the socket into the glass shade, thread the three set screws through each holes of glass shades, and then secure them into the glass holder. Canopy Coupling Kit 9. Repeat with the other glass shade. 10.
PAGE 3
. Thread two headless screws through the mounting plate, and then secure them with four lock nuts (two on each side of the mounting plate). Adjust the length of the headless screws if necessary. Note: Make sure that the headless screws are lined up horizontally to make the fixture level. 4. Attach mounting plate to the outlet box using two mounting screws. 5. Connecting the wires with wire connectors as follows: ---Connect the black wire from the fixture to the black wire from the power source.
PAGE 4
For Wall Light A: 16-1/2" B: 36-1/2" C: 9" For Pendant A: 16-1/2" B: 89"