Assembly Instruction

ManualsBrandsWilliston Forge ManualsCeiling LightsDimaggio 3 - Light Lantern Geometric Pendant

1of3

(3)B10CandelabraBaseBulbs60WMaximum.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Fixture Loop

6” Rod

Socket Assembly

12” Rod with Nipple

Center Column

STEP 1 Install ,

Center and

Side Arms

- Center Column

Rod, Socket Assembly

A. Thread the (E), the

Center and the Socket

Assembly (G) together as shown.

Hand tighten until snug.

Center Column

Rod (F)

B. Place the bolt on the top end of Side

Arms (J) through holes on the plate

of the Center Column (E) and secure

with Lock Balls (H). Hand tighten

until snug.

Hardware Contents

Crossbar

Assembly

Ceiling

Canopy

Quick Link

Shade

Center Rod

Lock ball

Side Arm

STEP 2 Install Fixture Loop and

Rods to Center Column

A. Determine the Rods (B/C/D) to be

assembled to the Center Column (E)

according to your hanging height.

B. Pass the supply wires and ground

wire through the chosen rods

(B/C/D) and the Fixture Loop (A).

Thread the Center Column (E), the

chosen Rods (B/C/D) and the

Fixture Loop (A) together. Hand

tighten until snug.

Suggested rods for Ceiling height:

8’ ceiling : use (1) 12” rod

9’ ceiling : use (2) 6” rods and (1) 12”

rods

10’ ceiling : use (2) 6” rods and (2)

12” rods

Supply Wires and

Ground Wire

Figure 2

12” Rod

Plate

Bolt

Figure 1

Assembly Instruction Sheet

Thank you for purchasing

Summary of content (3 pages)

PAGE 1
Assembly Instruction Sheet Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (3) B10 Candelabra Base Bulbs 60W Maximum. Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture.
PAGE 2
STEP 3 - Install the Crossbar Assembly to Outlet Box and Adjust the length of the Nipple STEP 5 - Making the Wire Connections A. Attach the Crossbar Assembly (AA) to the Outlet Box with the head of the Green Ground Screw facing you. Secure it with Outlet Box Screws (not included), tighten until snug . B. Adjust the hex nut and lock washer underside of the crossbar to the middle of the nipple. C. Remove the canopy lock ring from the canopy chain loop.
PAGE 3
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4" FINISH: MOTTLED BLACK 5” Dia. 63” OVERALL HEIGHT INCLUDES SINGLE CHAIN, QUICK LINK, (2) 6” RODS AND (2) 12” RODS 21.5” 8.5” 14” Dia. 14.5” Dia.