Assembly Instruction

1of2
Package Contents
Crossbar
x1
Assembly
A
STEP 1 Install Crossbar-
A. A)Attach the Crossbar ( to the
Outlet Box with the head of the
Green Ground Screw facing
you. Secure it with Outlet Box
Screws (not included)
Tighten until snug
.
.
Figure 1
Outlet Box
Outlet Box Screw
(not included)
Green Ground Screw
B
Fixture Body
x1
STEP 2 Test Fit the Backplate to the Crossbar Assembly-
a. Remove lock ball from crossbar assembly.
Shade
x2
C
D
Lock Screw
x6
A
Outlet Box
Backplate
Lock Ball
Hex Nut and
Lock Washer
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Figure 3
Figure 2
STEP 4 Install- Fixture Body
A. Re-attach the backplate and
Fixture Body (B) to the Crossbar
Assembly (B). Secure with the
previously removed lock ball.
B
b. Fit backplate of Fixture Body (B)
over the nipple on Crossbar
Assembly (A) and secure with
lock ball.
The backplate should be
snug against the wall and the lock
ball. If not, adjust the length of
the nipple on the Crossbar
Assembly (A) by unscrewing the
preassembled hex nuts. Then,
screw the nipple in or out of the
crossbar until the desired length
is achieved. Once the backplate
is secure, remove the lock ball
and backplate and proceed to
Step 3.
Note:
Outlet Box
Backplate
Lock Ball
B
Figure 4
STEP 5 - Install Shade and Bulb
A. Place Shade (C) into the socket
cup with the joint of the mesh is
against the backplate. Thread
Lock Screws (D) onto socket
cup to engage the neck of the
Shade (C). Carefully release
your hands after all Lock
Screws (D) are tighten
properly.
B. Insert bulbs onto sockets and
screw snugly into place.
Your fixture is now assembled
and ready to use. Enjoy!
C
D
Vintage Bulb
(recommended
but not supplied)
Socket
Figure 5
Neck
Joint
Backplate
(2)A19MediumBasebulbs100WMaximumor
(2)MediumBaseVintagebulbsarerecommendedbutnotsupplied.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Thank you for purchasing
Assembly Instruction
Pleasegoto the productcleaningtips.GototheCare + Maintenance selection.