Installation Guide

1of2
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
(3)A19MediumBaseBulb100WMaximum,bulbnotincluded.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.MissingParts?Contactyouroriginalplaceof
purchase.
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Package Contents
A
Crossbar
Assembly
x1
Fixture Body
x1
C
Figure 1
STEP 1 Installing the Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 3
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
(Step 2 Continued)
the mounting screws on the Crossbar Assembly (A) by
unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws in or out of the crossbar until the
correct length is achieved. Once the backplate and Fixture Body
(C) is secure, remove the mounting ball and Fixture Body (C) and
proceed to Step 3.
STEP 4 - Install the
Fixture Body
A. Position the backplate
and Fixture Body (C)
onto the Crossbar
Assembly (A). Place the
holes in the backplate
over the mounting
screws. Secure the
Fixture Body by using
the mounting balls and
hand tighten the
mounting balls until
snug.
Figure 4
B
Alternate
Mounting screw
x2
STEP 2 Test Fit the
Backplate to the Crossbar
Assembly
-
A. Remove the mounting
balls from the Crossbar
Assembly (A). Place the
backplate and Fixture
Body (C) onto the
Crossbar Assembly (A)
and secure with mounting
balls. Note: The backplate
and Fixture Body (C)
should be snug against
the wall and held tight with
the mounting balls. If it is
not, adjust the length of
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
Figure 2
C
Mounting Screw
or Alternate Short
Mounting Screw
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
Outlet Box
A
Mounting Ball
A
Backplate
C
Mounting Screw
or Alternate Short
Mounting Screw
Installation Guide