Installation Guide

ManualsBrandsWilliston Forge ManualsCeiling LightsDenslowe 8 - Light Kitchen Island Linear Pendant

1of2

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

(8)A19MediumBase100WbulbMaximum,bulbnotincluded.

MinimumHangingHeightis24”,MaximumHangingHeightis51”.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.MissingParts?Contactyouroriginalplaceof

purchase.

LightSource:

FixtureHangingHeight:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Package Contents

Hardware Contents

Ceiling

Canopy

Fixture Chain

Quick Link

Crossbar

Assembly

Fixture Body

STEP 1 - Install the Crossbar Assembly to Outlet Box and Adjust

the length of the Nipple

A. Attach the Crossbar Assembly (AA) to the Outlet Box with the head

of the Green Ground Screw facing you. Secure it with Outlet Box

Screws (not included), tighten until snug

B. Adjust the hex nut and lock washer underside of the crossbar to the

middle of the nipple.

C. Remove the and Hex Nut from the Nipple. Place the

Ceiling Canopy over the Nipple against the ceiling to determine the

correct position of the nipple. Thread the Finial onto the Nipple.

Adjust the nipple to allow the Ceiling Canopy to rest against the

ceiling when held in place by the .

D. Remove the and the Ceiling Canopy(DD). Tighten the lock

washer and the hex nut against the crossbar to secure in place.

Lock Ball

Outlet Box Screw

(not included)

Hex Nut and

Lock Washer

Outlet Box

Green Ground Screw

Lock Ball

Figure 1

Nipple

Hex Nut

Supply Wires

and Ground Wire

STEP 2 - Install Fixture Chains

a. Adjust the Fixture Chain (BB) to your desired length by removing

the links if needed.

b. With the Fixture Chain (BB) not attached to the fixture loops and

the ceiling loops underside of the Ceiling Canopy (DD), pull the

supply wires and ground wire through the Fixture Chain (BB)

alternating links. After the wires are through the Fixture Chain

(BB), pull the supply wires and ground wire through the Ceiling

Canopy (DD).

c. Attach one ends of the Fixture Chains (BB) to fixture loops with

Quick Links (CC) as shown. Lift the fixture and Fixture Chains (BB)

up and attach the other ends of the Fixture Chains (BB) onto the

ceiling loops underside of the Ceiling Canopy (DD) with the rest

Quick Links (CC).

Suggested rods and chain length for Ceiling height :

8’ ceiling : use 30 links of chains and 4 quick links

9’ ceiling : use 40 links of chains and 4 quick links

Installation Guide

Summary of content (2 pages)

PAGE 1
Installation Guide Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (8) A19 Medium Base 100W bulb Maximum, bulb not included. Fixture Hanging Height: Minimum Hanging Height is 24”, Maximum Hanging Height is 51”. Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts are present.
PAGE 2
STEP 3 - Attach the Lanyard STEP 6 - Install the Bulb A. The purpose of the lanyard is to provide a means to support the fixture hands free from the junction box while connecting the electrical wires. B. Turn the Button Stop so it may be inserted into a Crossbar slot. Make sure the Button Stop is completely inside the Crossbar. Slowly release the fixture to make sure it is supported by the Button Stop. Proceed to the wiring steps in the next step.