Assembly Instructions

IMPORTANT:
• ALLINSTALLATIONWORKSHOULDBEDONEBYACCREDITEDPROFESSIONAL.
• SHUTOFFPOWERSUPPLYATFUSEORCIRCUITBREAKER!
• USEONLYTHESPECIFIEDBULBS.DONOTEXCEEDTHEMAXIMUMWATTAGE!
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the xture with a clean lint-free cotton or microber
cloth. Never spray cleaner directly onto the xture.
For Customer Service, please
contact the place of purchase.
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important
notes above. Remove the old xture from the ceiling, including the
old mounting strap.
1.Takethemountingstrapassemblyfromthepartsbag.Mounting
strap(B)containsseveralthreadedholes.Twoofmountingscrews
(A)shouldbeattachedtomountingstrap(B).Youmayneedto
tightennuts(C)thatholdthesescrewsinplace.Ifthescrewsare
notattached,pleaseholdcanopy(F)uptomountingstrap(B).Line
uptheholesincanopy(F)withtheholesinmountingstrap(B)and
insertmountingscrews(A)intomountingstrap(B)sothatmounting
screws(A)protrudethroughtheholesincanopy(F).Mounting
screws(A)arelong,pleasetestcanopy(F)againstthemounting
straptoseehowfaryoushouldinsertthescrews.Tightennuts(C)
ontomountingscrews(A)toholdthescrewsinplace.
2.Placemountingstrap(B)overthejunctionboxsothatmounting
screws(A)arevertical,andinalignmentwiththeholelocations
oncanopy(F).Securemountingstrap(B)tothejunctionboxwith
mountingscrews(D)andascrewdriver.Tightenthescrewssecurely.
CONNECTING THE WIRES
4.Haveanassistantsupportthexture’sweightwhilecompletingthewiring.Refertothewiringdiagrambelowandattachthexture’s
wirestothepowersupplywiresfromthejunctionbox.ConnectHottoHot,NeutraltoNeutral,andGroundtoGround.Twisttheends
ofthewirepairstogether,andthentwistonawireconnector.Makesurealltwistsareinthesamedirection.Ifthereisnohouseground
wirecomingfromthejunctionbox,locategroundscrew(E)onthemountingbracket/mountingstrapandwrapthexture’sground
wirearoundthegroundscrew.Useascrewdrivertotightenthetopofgroundscrew(E)ontothewiresandintothemountingbracket/
mountingstrap.Tuckthewiresintothejunctionbox.
FINISHING THE INSTALLATION
5.Raisecanopy(F)totheceiling.Positionmountingscrews(A)sothattheyprotrudethroughtheopeningsofcanopy(F).Securecanopy
(F)inplacewithdecorativenuts(H).
6.Connectsiderods(G)tocage(P).Haveanassistantsupporttheweightofthecage.Connectthetopsofrods(G)tocanopyhooks(I).
Installlightbulbs(notincluded)inaccordancewiththexture’sspecications.
Yourinstallationiscomplete.Turnonthepowerandtestthexture.
Assembly Instructions
ASSEMBLING THE FIXTURE
3.Connectcenterrod(N)topost(M)ofthexture’sbody.Connect
hook(L)tocanopyloop(K).
H
I
B
D
A
E
C
G
F
M
N
K
L
J
P
House Wires
Fixture Wires
Hot
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread