Instructions / Assembly

ManualsBrandsWilliams ManualsGarden CenterDigital Wall Thermostat

REV.9/27/05 Page 1 of 7

TS-3

INSTALLATION AND OPERATING INSTRUCTIONS

INTRODUCTION

This TS-3 wired wall thermostat was developed to provide a safe, reliable control system for gas heating appliances. The system can

be operated thermostatically or manually from the wall unit.

WALL MOUNT THERMOSTAT

The TS-3 wired thermostat operates on (2) 3V Button Cell (Included) which powers the LCD screen

and circuit board. Before using the TS-3 wall thermostat the 3V batteries must be installed into the

battery compartments.

It is recommended that CR2032 lithium batteries always be used for longer battery life and

maximum operational performance. If the LCD screen will not come on, check the 3V Button Cell

battery.

TO INSTALL BATTERIES IN THE THERMOSTAT

1. Remove face from backing wall plate this is done by sliding the face up about 1/2” then pull the face off the base plate. As

shown in Figure #1

2. Locate the (2) holders for the 3V button cell batteries.

3. Slide the button cell batteries into the battery holders. (Make sure that the batteries are installed with the (+) plus side facing

you or up.

4. Reinstall the face to the backing plate this is done by sliding the face in and down about 1/2” then check that the (2) male

terminal connectors on the face are engaged in the female terminal connectors on the backing plate . As show in Figure #1

TO REMOVE THE BATTERIES FROM THE THERMOSTAT

1. Remove face from backing plate this is done by sliding the face up about 1/2” then pull the face off the base plate. As shown in

Figure #1

2. Locate the (2) holders for the 3V button cell batteries.

3. Insert a small screwdriver into the slot above the button cell battery and push the battery out. As shown in Figure #2

4. Reinstall the face to the backing plate this is done by sliding the face in and down about 1/2” then check that the (2) male

terminal connectors on the face are engaged in the female terminal connectors on the backing plate. As show in Figure #1

Figure #1 Figure #2

IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT

ATTEMPT TO INSTALL OR OPERATE

ROOM

TEMP

THERMO

MODE

“SET”

SET

OFF

LCD

DISPLAY

ON/UP

BUTTON

OFF/DOWN

BUTTON

SET

BUTTON

(2) 3 Volt Button

Cell Batteries

Battery Removal

Slots

Plus

Side

Plus

Side

ROOM

TEMP

OFF

SET

Summary of content (7 pages)

PAGE 1
I TS-3 INSTALLATION AND OPERATING INSTRUCTIONS IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT ATTEMPT TO INSTALL OR OPERATE INTRODUCTION This TS-3 wired wall thermostat was developed to provide a safe, reliable control system for gas heating appliances. The system can be operated thermostatically or manually from the wall unit. WALL MOUNT THERMOSTAT The TS-3 wired thermostat operates on (2) 3V Button Cell (Included) which powers the LCD screen and circuit board.
PAGE 2
WIRED WALL MOUNT THERMOSTAT OPERATION FUNCTIONS 1 2 3 ROOM SET TEMP 5 ROOM SET 1. 2. 3. 4. 5. ROOM TEMP – Current room temperature. F – Degrees Fahrenheit (C Indicates degrees Celsius) FLAME ICON – Indicates APPLIANCE IS ON. SET- Indicates TS/R-3 is in thermostat mode. DASHES – Indicate thermostat mode is being disabled. When TS-3 is not in the thermostat mode. The word (SET) will not appear. TEMP 4 1. SET OFF ON 2.
PAGE 3
INSTALLATION INSTRUCTIONS WALL MOUNTING THE TS-3 THERMOSTAT 1. 2. 3. 4. 5. 6. Remove face from backing plate as shown in Figure #1 then locate the TS-3 to where the (2) thermostat wires from the appliance can be pulled through the hole on the backing plate and connect them to the (2) terminal screws. After locating the (2) two mounting holes and mark the holes on the wall. Use the (2) two dry wall anchors and screws (that are supplied) to mount the base plate to the wall as shown.
PAGE 4
Other Appliance Power supply Could be 12VAC, 12VDC, 24VAC (2) wires from the appliance (Not Included) RO OM TE MP ON SE T OF F (2) Screw terminals to connect wires from appliance TS-3 Wired Wall Thermostat Figure #5 (Other Appliances) SYSTEM CHECK MILLIVOLT VALVES - ELECTRONIC IGNITION SYSTEMS – OTHER APPLIANCES Light your gas appliance following the lighting instructions that came with the appliance.
PAGE 5
2. 3. 4. The TS-3 has (2) 3 volt button cell batteries (1) button cell operates the LCD screen and the other button cell powers the PCB board. If the button cell battery that controls sending the PCB board is low or defective the LCD screen may work but the PCB relay may not close the contact (Check each button cell battery) Check that the (2) male terminal connectors on the face are engaged in the female terminal connectors on the backing plate.
PAGE 6
Limited Lifetime Warranty SKYTECH II warrants the SKYTECH REMOTE CONTROL SYSTEM for a Limited Lifetime of the original owner of this system. This warranty is not transferable to another person it is for the original purchaser of the product. Should any part fail because of defective workmanship or material from the original date of purchase SKYTECH II will repair or, at SKYTECH II option, replace the defective parts.
PAGE 7
Santa’s Helper Exclusive offer to Skytech Remote Control Owners This special offer is only provided to customers of Skytech II, Inc. that have purchased a remote control for their Hearth Product. This remote control system can be used for any 110Volt appliance, but perfect your Christmas Tree Lights or any other appliance that is difficult to reach or plug in. Simply plug the receiver into your wall outlet and your appliance into the receiver, push the on button on the transmitter and you are in business.