Instructions / Assembly

[
'-'tF
I
ll
rnrg
Krr
rs FoR
usE wrrH
MoDEL
NUMBERS:
il
ii
z:,,tztr1liglr:affiffi,i
ll
I
This conversion
kit
shall
be iristalled
by
a
qualified
I
soorszr;soorszr;sooeszr;
f f
service
agency
in
accordance
with
tt'1.
I
5001e22;5002522:5002e22
ll
manutactur6r's
instructions
and
an ,ppii.rLi.
I
3331#;6501e22;6502521;
ll
codes and
requirements
of
the authority
having
I
| |
jurisdiction.
lf
the
information
in these
instructions
I
rHls
coNVERSIoN
Ktr ls'
II
i' not
.foltowe{
exactty,
"
n",
"-d;;il
;;
|
}!??5fft33;yr1:lyrl1;i
f f
nroduction
of
carbon
monoxide
may resull
causing
I
esazszzisoorszr;s001e21
| |
property
damage,
personal
injury or
loss
of
life.
I
s001522;
s001s22;
5002522',
| |
tn"
quilit"d
.Jri."
asency
is responsiue
ror ine
I
33313il;
33313f;
nT,i3'#
| |
proper
installation
of this
kit. The installation
is
not
I
wrn
piopnr,re
desaruo r
| |
propdr
and
-coffiel.6-untii
the operafnn
of
tfre
l-Vnr-ve
eEnT-N-U-trlEER-6ooi
ll
converted
apptiance
is checked
as
speciReo
in ine
I I
milytrSprf""J!
|[
manufacturer's
instructions
supplied
with
the
kit.
I
l.fgf';3,;iitlffi
ill
I
58s,-xt.:rYg^irFli;
r+-
I I
plp_g.oNry.E9rlIc rHE ELECTRIcAL
poyFt
gr
lourneeo I
wA,RN1NG:
rHE
ry1LLIAMS
I lwrH
BLowER)
BEFoRE
pRocEEDtNG
'
wtrH
rHe
I
'
l\trvtrK
tsE
USEU
UN
ANY
(
I
VALVE.
Do
NoT
USE
THTS
I
rou-owro
exnCtr-X
A FIRE
on n explosrij'1.i
itany iEduli
I
RoBERTSHAW
BRAND
GA
I
cnustttc
PRoPERTy
DAMAGE,
pensoruir--iNiiJiiibRIdss
I
UNABLE
to omenutrur
I
f
or
ure.
,
-
..
'
:
-
"'--
.'-
1.
-::--::
|--N-IJ-MFEB'
D-o-NorcoNVEF
II
rr
|
(1)
pREssuRE
REGULA'roR
(4)
ptLor
oRtFtcES
(NATUML
GAs)
|
I
(1)
BURNER
oRrFrcE
(NATUML.
GAs)
(2)
coNVERStoN
LABELS
I
.
[
(z)
scREws
(1)
NATUML
GAS
TAG
I
CONVERSION
INSTRUCTIONS
-
L.P.
GA.S
TO
NATURAL
I
1. Shut
off
gas
to the furnace.
2. Shut
off
electric
power
to
the
furnace
(lf
equipped
with
blower)
3. Disconnect
gas
supply
line
fom control
valve.
4.
Disconnect
thermostat
wires
from control
valve.
CAUTION:
Label
all
wires
prior
to disconnection
for
proper
reconnection
5.
Remove
burners
by unscrewing (2)
Phillips
head screws.'
,
6. Use
a boxed
end
wrench
and
remove the
main
burner
orifices
(2)
from the
manifold
orifices
provided
in this..kit.
See
Figure belorai.
7.
Remove
pilot
orifice
from
pilot
and replace
with orifice
provided
in this
kit.
See
Figure 2,
q. To replace
the
pressure
regulator
on the
gas
valve.
Refqr
to
Figure
1.
9.
Push in
gas
con[rol
knob
slightly
and tum clockwise
,a\
to
"OFF,.
10,
Remove
(2)
screws
from
the
pressure
regulator.
/
\
11. Lift the
pressure
regulator
and
gasket
from
valve
and
discard.
12. lnstall
the
new
gasket,
pressure
regulator and
(2)
screws
from
this
conversion
kit.
IMPORTANT
Discard
old
gasket
and
screws.
Do
not reuse.
.13.
IMPORTANT:
check
the
location
of
the
pilot
to the
bumer.
See
Figure
4.
.14.
Reassemble
the furnace
by following
Steps 1 thru
S in reverse
order.
CA'UTION:
THE
GAS
SUPPLY
SHALL
BE
SHUTOFF
PRIoR
To
DISCONNECTING
THE ELECTRICAL
POWER
(IF
EQUIPPED
WITH
BLOWER)
BEFORE
PROCEEDING
WITH
THE
CONVERSION.
WA'RNING:
IF
THE INFORMATION
IN THIS
MANUAL
IS NoT
FOLLOWED
ryNCTLY
N FIRE
OR
A EXPLOSION
MAY
RESULT
CAUSING
PROPERTY
DAMAGE,
PERSONAL
INJURY
OR LOSS
THIS
KIT
CONTAINS;
(1)
PRESSURE
REGUHTOR
(4)
PILOT
ORIFICES
(NATURAL
GAS)
(1)
BURNER
ORIFICE
(NATURAL.
GAS)
(2)
CONVERSION
LABELS
(2)
SCREWS (1)
NATUML
GAS
TAG
This conversion
kit
shall
be
installed
by
a
qualified
service
agency
in
accordance
with
the
rnanufacturer's
instructions
and
all
applicable
codes
and
requirements
of
the authority
having
jurisdiction.
lf
the
information
in these
instructions
is not
followed
exactly,
a
fire, explosion
or
production
of
carbon
rnonoxide
rnay
result,
causing
property
darnage,
personal
injury
or
loss
of
life.
The
qualified
seruice
agency
is
responsible
for the
proper
installation
of
this
kit, The
installation
is
not
properandcornptete_-[ntii.theoperatiffi
convefted
appliance
is checked
as
specified
in the
rnanufacturer's,instructions
supplied
with
the
kit.
P3?3291
tt-A,917-99
1
0F
4