Digi-Wave™ 2.0 DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver USER MANUAL DLT 100 2.0 DLR 60 2.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver Digi-Wave™ DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver Contents Digi-Wave™............................................................................................................................................................................. 2 DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver ...................................................................................... 2 System Overview.........
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver FAQs...................................................................................................................................................................................... 28 FCC statements..................................................................................................................................................................... 29 2-year Warranty...........................................................
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver System Overview The Digi-wave™ system is a patented, digital spread-spectrum (DSS), simultaneous two-way wireless listening system operating in the 2.4 GHz band. Due to it’s frequency-hopping algorithm, it avoids interference and is a very secure method of communication.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver Getting Started: Preprogrammed Systems If a system has been purchased, you will not need to perform any programming. The system will have been configured to your order. Turn chairman master on first so other units can pair. Slave units will turn off after 5 minutes if they cannot find a master. 1. Charge all DLT 100 2.0’s. If using DLR 60’s, either charge them with NiMH batteries or insert fresh Alkaline batteries.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver Before Programming the Digi-Wave™ System Prior to programming the system, decide what mode you will need, and what priority each DLT will have. Any two people can talk in a group at any given time. The CM will have first priority, CS has second priority and Slave units have third priority. The CM or CS will have to turn off their talk access to allow the Slave units to talk.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver There must be one Master (usually this is also the floor), and only one, per group. Each Interpreter must be assigned their own channel number. Repeater function can only be used in 1-Way mode. When repeater function is used, all 15 channels can be utilized in one-way mode, i.e. one floor and 14 interpreters. When repeaters are used, Floor (channel 0) must be assigned as the master unit for the group.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver Programming the Digi-Wave™ System for 2-way Mode There are 4 basic steps to programming a Digi-wave system: 1. Set Mode: 2-way or 1-way 2. Set Priority: Chairman Master, Chairman Slave, and Slave 3. Set Address 4. Set Group Number Most of the programming is done on the DLT 100 2.0(s); the receivers just need to be assigned the correct group number.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver Programming the Digi-Wave™ System for 1-way Mode(s) There are 4 basic steps to programming a Digi-wave system: 1. Set Mode: 2-way or 1-way 2. Set Priority: Chairman Master, Chairman Slave, and Slave 3. Set Address 4. Set Group Number Most of the programming is done on the DLT 100 2.0(s); the receivers just need to be assigned the correct group number.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver Programming the Digi-Wave™ System: DLT 100 2.0 Optional Settings Secure Key Code: When a group has been set up and the same Secure Code has been entered into all the DLT 100 2.0’s, the DLT 100 2.0’s without this Secure Code entered cannot listen in on the group. This may be desirable in private or high security-level functions. The same four digit code must be programmed into all of the DLT’s, Chairman Master, Chairman Slave and Slaves.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver Address Confirmation Press the MENU button twice for the CM and CS, once for SLVs. The address for the DLT 100 2.0 will be displayed for two seconds. NOTE: Every DLT 100 2.0 MUST have its own address and all must be assigned to the same group. Quick Group Change “Groups” apply to 2-way Mode only. until the GROUP indicator on the 1. With the DLT 100 2.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver DLT 100 2.0 Controls INTERNAL SPEAKER LCD DISPLAY LED INDICATORS TALK BUTTON VOLUME / SELECT UP VOLUME / SELECT DOWN POWER / MENU HEADPHONE JACK 3.5 MM MIC JACK 3.5 MM INTERNAL MICROPHONE 30-PIN CONNECTOR A468 DLT 100 2.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver ·· Use these buttons to select channels in simultaneous interpretation mode ·· QUICK GROUP CHANGE / SETUP BUTTONS ·· Press and hold and together for 3 seconds to enter or exit setup menu ·· Press and hold button for 3 seconds to enter quick group change mode. The GRP light will flash. Then use or to change groups. To exit, push again or just wait until the unit times out.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver DLR 60 2.0 Controls HEADPHONE JACK LANYARD SLOT STRENGTH DLT#1 STRENGTH DLT#2 ANTENNA SYMBOL NUMERIC TYPE BATTERY STRENGTH NUMERIC DISPLAY RED LED GREEN LED VOLUME ADJUST CH/GROUP CHANGE POWER DOCKING CONNECTOR DLR 60 2.0 Operation SPEAKER 1. Insert 2 AAA batteries into the DLR. Be sure to observe correct polarity.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver Example 1: 2-way Mode, Tour Guide How it works 1. Tour Guide 1 speaks, using a DLT 100 2.0 alone (built-in mic) or using it with a compatible headset mic. 2. Each Tour Group Member and Tour Guide 2 listen directly to Tour Guide 1, each using a DLT 100 2.0 alone (built-in speaker) or using it with a compatible headset mic. 3. Tour Guide 2 then speaks, using a DLT 100 2.0 alone (built-in mic) or using it with a compatible headset mic. 4.
DLT 100 2.0 Digital Transceiver and DLR 60 2.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver y nl O ve R ec ei 2W ay 2-WAY MODES 2W ay (i. e. To u rG ui de ) 2-Way Setup for Tour Guide Operation 1 2 3 Press and hold POWER button for 2 seconds to turn DLT 100 2.0 on Press and together for 3 seconds to enter programming mode. Mode icon will blink on the LCD screen. 5 6 7 Press POWER / MENU button to enter selected Tour Guide mode (shown above) and advance to the next setting.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver 2-Way Setup for Tour Guide Operation (continued) 9 Address ( ADD ) icon will now begin to blink. Use the buttons to select a Address number ( 0 – 1023 ). 10 button to enter Press Address number and move to the next setting. Note: Attendee count will only work with addresses 1-99 (Maximum 100 DLT 100 2.0’s with one Master at address 0). 13 If this is a slave unit, the side-tone adjustment will be displayed (not avail on CM or CS).
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver Example 2: Simultaneous Interpretation (1-way) How it works 1. The Main Speaker will use channel 0; Press the TALK button to activate the microphone 2. Each Interpreter unit will need to be assigned a channel number (1-14). The TALK button must be activated to send the interpretation to the attendees. 3. The floor speaks, using a DLT 100 2.0 alone (built-in mic) or using it with a compatible headset mic. 4.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver re te r) te rp (In R ec ei Sp ea k ve /S pe ak y O nl O ve R ec ei R ep ea te r 1-WAY MODES nl y (M ai n Sp ea ke r) 1-way Setup for Simultaneous Interpretation 1 2 3 Press and hold POWER button for 2 seconds to turn DLT 100 2.0 on. Press and buttons together for 2 seconds to enter programming mode. Mode icon will blink on the LCD screen.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver 1-way Setup for Simultaneous Interpretation 9 10 11 12 Channel icon will now begin to blink Press ( + ) or ( - ) button to select a Channel number 1 – 14. Transmitting Channel must be set different. ( N/A with Main Speaker unit. Set to CH 0 ). Press POWER / MENU button to enter Channel number. Group icon will now blink. Press POWER / MENU button to enter Group number.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver Repeater Mode An additional DLT 100 2.0 can be set-up as a repeater to increase the range of each channel. When repeater mode is used, the main speaker’s DLT is no longer the master - the master (unit all others sync to) now becomes one of the slaves. Main Speaker (Floor) DLT Must be set to Main Speaker, CH 0 and SLV. Main Speaker (Floor) DLT Repeater Interpreter DLT’s Must be set to Repeater, CH 0 and MAS.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver Differences between DLT 100 2.0 and DLT 100 Function/Description DLT 100 2.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver Differences between DLR 60 2.0 and DLR 60 Between 08/13 and 11/13, a limited number of DLR 60’s were manufactured and sold to the marketplace. If the front of the unit says “Digi·WAVE”, you have a DLR 60. If it says “DIGI·WAVE 2.0”, you have a DLR 60 2.0. Most units are the DLR 60 2.0, so this section may not apply to your product. Function/Description DLR 60 2.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver Specifications DLT 100 2.0 Transceiver Dimensions Weight Color Enclosure Battery type Battery life Charge time 103 x 62 x 11mm (4.1 x 2.4 x 0.4 inches) 80g (2.8oz) including battery Black and silver Shatter resistant PC/ABS plastic Li Polymer with smart charge built into transceiver Up to 14hrs talk time per charge 5hrs.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver Specifications DLR 60 2.0 Receiver Dimensions: Weight: Frequency Band: Modulation: 2.36” W x 3.54” H x 0.63” D (60 mm x 90 mm x 16 mm) 1.7 oz. (47g) without batteries. 2.
DLT 100 2.0 Digital Transceiver and DLR 60 2.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver FAQs What is the range of the system? Up to 100ft outdoors and up to 200ft indoors. (The range always depends on the environmental conditions). What is the benefit of this system over the 72MHz systems? DLT’s can operate in two way mode. Team teach/tour guide ability. Voting feature for discussion mode. Relay feature increases range. Harmonized frequencies for international use.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver FCC statements Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
DLT 100 2.0 Digital Transceiver and DLR 60 2.0 Digital Receiver 2-year Warranty Williams Sound products are engineered, designed, and manufactured under carefully controlled conditions to provide you with many years of reliable service. Williams Sound warrants the DLT 100 2.0 and DLR 60 2.0 against defects in materials and workmanship under normal use and conditions for 2 years from date of purchase.
DLT 100 2.0 Digital Transceiver and DLR 60 2.
10300 Valley View Rd • Eden Prairie, MN 55344 800-328-6190 / 952-943-2252 • FAX: 952-943-2174 www.williamssound.
