Manualshelf

Installation Instructions

ManualsBrandsWilliams Architectural Products ManualsLandscape LightingWilliams Railing Solar LED White Perimeter Post Cap Light
1
INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS
SOLAR 3" LED PERIMETER POST CAP – ASSEMBLY P/N: LS045310
1. INSTALL
INTO
LIGHT HOUSING
AS SHOWN.
2. ATTACH
LIGHT HOUSING
ONTO
POST
AND SECURE USING
AS SHOWN.
3. PLACE
CAP
ONTO
LIGHT HOUSING
AND SECURE USING
.
#2 PHILLIPS DRIVER
INSTALLATION INSTRUCTIONS
CAP WITHOUT LIGHT
CC025303
1. INSTALL
INTO
LIGHT HOUSING
AS SHOWN.
2. ATTACH
LIGHT HOUSING
ONTO
POST
AND SECURE USING
AS SHOWN.
3. PLACE
CAP
ONTO
LIGHT HOUSING
AND SECURE USING
.
#2 PHILLIPS DRIVER
INSTALLATION INSTRUCTIONS
CAP WITHOUT LIGHT
CC025303
1. INSTALL
INTO
LIGHT HOUSING
AS SHOWN.
2. ATTACH
LIGHT HOUSING
ONTO
POST
AND SECURE USING
AS SHOWN.
3. PLACE
CAP
ONTO
LIGHT HOUSING
AND SECURE USING
.
#2 PHILLIPS DRIVER
INSTALLATION INSTRUCTIONS
CAP WITHOUT LIGHT
CC025303
1. INSTALL
INTO
LIGHT HOUSING
AS SHOWN.
2. ATTACH
LIGHT HOUSING
ONTO
POST
AND SECURE USING
AS SHOWN.
3. PLACE
CAP
ONTO
LIGHT HOUSING
AND SECURE USING
.
#2 PHILLIPS DRIVER
INSTALLATION INSTRUCTIONS
CAP WITHOUT LIGHT
CC025303
LIGHT HOUSING
CAP
PHILLIPS SCREWS
TREE CLIPS
POST
1. INSTALL
INTO
LIGHT HOUSING
AS SHOWN.
2. ATTACH
LIGHT HOUSING
ONTO
POST
AND SECURE USING
AS SHOWN.
3. PLACE
CAP
ONTO
LIGHT HOUSING
AND SECURE USING
.
#2 PHILLIPS DRIVER
INSTALLATION INSTRUCTIONS
CAP WITHOUT LIGHT
CC025303
4X 6-32 X 3/8” LONG
GASKET
4X CHRISTMAS
LIGHT HOUSING
CAP
PHILLIPS SCREWS
TREE CLIPS
POST
1. INSTALL
INTO
LIGHT HOUSING
AS SHOWN.
2. ATTACH
LIGHT HOUSING
ONTO
POST
AND SECURE USING
AS SHOWN.
3. PLACE
CAP
ONTO
LIGHT HOUSING
AND SECURE USING
.
#2 PHILLIPS DRIVER
INSTALLATION INSTRUCTIONS
CAP WITHOUT LIGHT
CC025303
4X 6-32 X 3/8” LONG
GASKET
4X CHRISTMAS
LIGHT HOUSING
CAP
PHILLIPS SCREWS
TREE CLIPS
POST
1. INSTALL
INTO
LIGHT HOUSING
AS SHOWN.
2. ATTACH
LIGHT HOUSING
ONTO
POST
AND SECURE USING
AS SHOWN.
3. PLACE
CAP
ONTO
LIGHT HOUSING
AND SECURE USING
.
#2 PHILLIPS DRIVER
INSTALLATION INSTRUCTIONS
CAP WITHOUT LIGHT
CC025303
4X 6-32 X 3/8” LONG
GASKET
4X CHRISTMAS
LIGHT HOUSING
CAP
PHILLIPS SCREWS
TREE CLIPS
POST
1. INSTALL
INTO
LIGHT HOUSING
AS SHOWN.
2. ATTACH
LIGHT HOUSING
ONTO
POST
AND SECURE USING
AS SHOWN.
3. PLACE
CAP
ONTO
LIGHT HOUSING
AND SECURE USING
.
#2 PHILLIPS DRIVER
INSTALLATION INSTRUCTIONS
CAP WITHOUT LIGHT
CC025303
4X 6-32 X 3/8” LONG
GASKET
4X CHRISTMAS
For additional product or installation assistance, please call 844-922-2368 (844-9-ACCENT).
For additional product or installation assistance, please call 844-922-2368 (844-9-ACCENT).
For additional product or installation assistance, please call 844-922-2368 (844-9-ACCENT).
For additional product or installation assistance, please call 844-922-2368 (844-9-ACCENT).
©2018 Railing Accents
™
All Rights Reserved. Version 1.1
©2018 Railing Accents
™
All Rights Reserved. Version 1.1
©2018 Railing Accents
™
All Rights Reserved. Version 1.1
©2018 Railing Accents
™
All Rights Reserved. Version 1.1
SOLAR 3" LED PERIMETER POST CAP – ASSEMBLY P/N: LS045310
SOLAR 3" LED PERIMETER POST CAP – ASSEMBLY P/N: LS045310
SOLAR 3" LED PERIMETER POST CAP – ASSEMBLY P/N: LS045310
Solar Post Cap Light Installation
Step 1 Remove the plastic tab from the battery
compartment to allow connection to the terminal.
Batteries are included with the solar post cap, but may
not be installed. Make sure batteries are seated firmly
in place.
Step 2 Apply an exterior-grade clear silicone
adhesive to the underside of the post cap and place
firmly on post.
Notes: The battery should last 3-5 years. The battery
is a LiFePO4 battery with a size of 14500, capacity -
600 mAh. Do not use regular batteries in the solar
post cap light. The solar panel will last the lifetime of
the light (15+ years). On a full charge, the lights will
last more than 24 hours. This reserve is to help with
cloudy day performance. The solar panel should fully
charge a completely dead battery in about 8 hours of
direct sunlight. The LED light output is 3000 Kelvin.
Solar Post Cap Light Installation
Step 1 Remove the plastic tab from the battery
compartment to allow connection to the terminal.
Batteries are included with the solar post cap, but may
not be installed. Make sure batteries are seated firmly
in place.
Step 2 Apply an exterior-grade clear silicone
adhesive to the underside of the post cap and place
firmly on post.
Notes: The battery should last 3-5 years. The battery
is a LiFePO4 battery with a size of 14500, capacity -
600 mAh. Do not use regular batteries in the solar
post cap light. The solar panel will last the lifetime of
the light (15+ years). On a full charge, the lights will
last more than 24 hours. This reserve is to help with
cloudy day performance. The solar panel should fully
charge a completely dead battery in about 8 hours of
direct sunlight. The LED light output is 3000 Kelvin.
Solar Post Cap Light Installation
Step 1 Remove the plastic tab from the battery
compartment to allow connection to the terminal.
Batteries are included with the solar post cap, but may
not be installed. Make sure batteries are seated firmly
in place.
Step 2 Apply an exterior-grade clear silicone
adhesive to the underside of the post cap and place
firmly on post.
Notes: The battery should last 3-5 years. The battery
is a LiFePO4 battery with a size of 14500, capacity -
600 mAh. Do not use regular batteries in the solar
post cap light. The solar panel will last the lifetime of
the light (15+ years). On a full charge, the lights will
last more than 24 hours. This reserve is to help with
cloudy day performance. The solar panel should fully
charge a completely dead battery in about 8 hours of
direct sunlight. The LED light output is 3000 Kelvin.
Solar Post Cap Light Installation
Step 1 Remove the plastic tab from the battery
compartment to allow connection to the terminal.
Batteries are included with the solar post cap, but may
not be installed. Make sure batteries are seated firmly
in place.
Step 2 Apply an exterior-grade clear silicone
adhesive to the underside of the post cap and place
firmly on post.
Notes: The battery should last 3-5 years. The battery
is a LiFePO4 battery with a size of 14500, capacity -
600 mAh. Do not use regular batteries in the solar
post cap light. The solar panel will last the lifetime of
the light (15+ years). On a full charge, the lights will
last more than 24 hours. This reserve is to help with
cloudy day performance. The solar panel should fully
charge a completely dead battery in about 8 hours of
direct sunlight. The LED light output is 3000 Kelvin.

Summary of content (1 pages)