Cut Sheet

Customer Service Department
7 Aviation Park Drive
Londonderry NH 03053
1-800-346-4175
1-603-647-5299 (International)
www.burndy.com
Catalog Item # Length Hole Hardware Torque
WEEB-BNDJMP6.7 30020147 9.0” overall,
8.3” hole-to-hole on center
0.257”
WEEB
®
washer, 1/4-20x 3/4 hex
screw, at washer, spilt washer, & nut
included unassembled
10 ft. lbs.
w/ Penetrox-A
on threads
WEEB-BNDJMP6.7AS 30020117 9.0” overall,
8.3” hole-to-hole on center
WEEB
®
washer, 1/4-20x 3/4 hex
screw, at washer, spilt washer, & nut
included assembled
WEEB-BNDJMP8.0 30020121 6.0” overall,
5.3” hole-to-hole on center
0.315”
WEEB
®
washer included
No mounting hardware
5/16-18 inch hardware recommended
WEEB-BNDJMP8.0AS 50010334 6.0” overall,
5.3” hole-to-hole on center
WEEB
®
washer, 5/16-18x1 hex
screw, at washer, spilt washer, & nut
included assembled
WEEB-BNDJMP9 50028011 9.0” overall,
8.3” hole-to-hole on center
0.257”
WEEB
®
washer included
No mounting hardware
1/4-20 inch hardware recommended
WEEB-BNDJMP12 50014641 12.0” overall,
11.3” hole-to-hole on center
WEEB
®
washer included
No mounting hardware
1/4-20 inch hardware recommended
WEEB-BNDJMP24 50014644 24.0” overall,
23.3” hole-to-hole on center
WEEB
®
washer included
No mounting hardware
1/4-20 inch hardware recommended
WEEB-BNDJMP36 50028017 36.0” overall,
35.3” hole-to-hole on center
WEEB
®
washer included
No mounting hardware
1/4-20 inch hardware recommended
The WEEB
®
Bonding Jumper is used to create an electrical connection between two pieces of anodized aluminum, galvanized steel, or
any electrically conductive metal which has been mechanically spliced. Long spans of mounting rails are sometimes constructed from
two shorter rail sections. Manufacturers may recommend that a oating splice be used to allow for thermal expansion. A oating splice
is rigidly attached to only one rail, and allows the rails to expand and contract in line with each other. In such cases, via NEC code, it is
also necessary to make an electrical splice, which can be done with a WEEB
®
Bonding Jumper. The Bonding Jumper is constructed of tin
plated, braided copper wire with a WEEB
®
washer attached at each end of the Jumper. The WEEB
®
washers provide a reliable, gas tight
electrical connection, and the braided copper wire allows for thermal expansion. All bonding jumpers are listed to ANSI/UL 467 by Intertek
ETL. Able to sustain equivalent current to 6AWG copper wire.
WEEB
®
BONDING JUMPER
4004188
• High quality grounding jumpers
• Corrosion resistant, tin plated, braided copper braid
• Available
- With WEEB
®
washer technology
- Assembled and unassembled
- With or without installation hardware
• Able to sustain equivalent current to 6AWG copper wire
• Available is standard lengths from 6” to 36”
• ETL Listed to ANSI/UL 467
• CSA Certied to C22.2 No. 41
• Custom designs available upon request