White LED Digital Scouting Camera User’s Manual Model # W4FT
Includes page 1 USB Cable 2 - Bungee Cords Camera Unit User Manual
Features RESOLUTION FLASH FLASH RANGE SENSOR SENSOR RANGE IMAGE FORMAT MEMORY USB IMAGE RESOLUTION POWER SUPPLY AUXILIARY POWER BATTERY LIFE ONBOARD POWER HOUSING MOUNTING REDUX MAX: 4 MP 2 High Intensity White LED’s up to 50 feet Passive Infrared Sensor (PIR) Motion and Heat up to 60 feet JPEG - Digital Still / AVI - Digital Video up to 32GB SD Card (not included) 5-PIN Mini USB style - included High (4MP) Medium (2MP) Low (1.
Installing Batteries 1. Open the door at the bottom of the camera by unlatching the locking tabs. Open Illustration A 2. page 3 With the camera facing open, open the battery compartment cover by sliding the latch to the left.
3. 4. Close battery compartment cover. To latch the cover simply pull the latch slightly to the left as you close the battery compartment cover. 5. Load SD memory card (up to 64GB not included) into the SD card slot with the connectors facing down. With the bottom of the camera towards you, Make sure to insert the batteries into the camera with the positive ends towards you where marked positive and the negative ends towards you where marked negative.
Power On 1. 2. To turn the unit ON press and release the power button. Check the battery level icon to ensure the batteries just installed contain the proper charge level. If so, you are ok to proceed with camera use. NOTE: LCD cycle through camera information. PIR picture number > Flextime number > Remaining pictures > Time page 5 Test Mode 1. LCD Ready Mode: The camera will automatically enter Ready Mode if a button is not pressed for greater than 30 seconds. 2.
Power Save 1. After 30 seconds without any buttons being pushed, the LCD will turn off and camera enters into Power Save or Ready Mode. 2. The LCD screen can be awakened by pressing the Power button briefly. Setting Time 1. To change date and time, start by pressing and release the center navigation button to set the hour. PO POWER Note: The LCD will not “wake up” when camera is writing to memory. 2. Press the left or right navigation button to go up or down Open in sequence. 3.
Setting Date 1. Press the center navigation button after setting the minute to change the Day. 2. Press the left or right navigation Open button to go up or down in sequence. 3. When the DAY is set, repeat steps Open 1 and 2 to set the Month and Year. page 7 Location 1. Press the center navigation button while Location is selected. The first character will be blinking. 2. Press the left or right navigation button to go up or down in sequence.
PIR Mode 1. Press the center navigation button while PIR Mode is selected. The highlighted option will be blinking. 2. Press the left or right navigation Open button to move to different options. Press the center navigation button to save the setting. PIR MODE: STILL: The camera takes still photographs. Open VIDEO: The camera takes 30 second videos. PIR Active 1. 2. Press the center navigation button while PIR Active is selected. The highlighted option will be blinking.
PIR Sensitivity 1. 2. Press the center navigation button while PIR Sense is selected. The highlighted option will be blinking. 1. Press the center navigation button while Picture is selected. The highlighted option will be blinking. Press the left or right navigation Open button to move to different options. Press the center navigation button to save the setting. 2. Press the left or right navigation Open button to move to different options. Press the center navigation button to save the setting.
Resolution 1. Press the center navigation button while Resolution is selected. The highlighted option will be blinking. 2. Press the left or right navigation Open button to move to different options. Press the center navigation button to save the setting. RESOLUTION: HI: Images will be at the highest resolution Open but take up the most space. MED: Images will be at medium resolution and take up average space. LO: Images will be at the lowest resolution and take up the least space. Delay 1.
Power Off 1. To turn the unit off, first wake up the LCD screen and then depress and hold the power button until the LCD turns off. Power Port 1. WGI Cameras come standard with an external power port. You must open the weather resistant cover and use a Wildgame Innovations 6 Volt camera battery accessory.
Mounting 1. When mounting to a tree, first latch the 2 bungee cords through the mounting holes on the left or right side of the camera. Then, stretch the cords around the tree and latch the other ends of the bungee cords through the mounting holes on the opposite side of the camera. Important Once you connect the camera to your computer via the USB cable/ports, the camera will then draw power from the computer.
Retrieving Images (SD Card in Camera) Method 1: Leave SD card in camera A. First, make sure that the camera is powered OFF. Next, plug the USB cable into the camera and then into the USB port on your computer. Once this is complete (in this order only), then power the camera ON. B. Once complete, your computer may automatically launch “AutoPlay”, a window recognizing a new Removable disk (the camera). C. If so, it should give you three selections: 1. Import pictures 2. View pictures 3.
Retrieving Images (SD Card reader) Method 2: Remove SD card and use card reader A. First, remove the SD Card from the camera unit itself by pressing on it to where it automatically ejects. B. Next, insert the SD card into your SD card reader. C. Once inserted into your computer it may automatically launch “AutoPlay”, a window recognizing a new Secure Digital Storage Device (the SD Card). D. If so, it should list several options for the next steps (not limited to the following): 1. Picture Options a.
Warranty DISCLAIMERS WGI Innovations, LTD. is not responsible for damage, expense or injury caused by the unauthorized use of, alterations to, improper connection of and abuse or neglect of the WGI Innovations™ products. WARRANTY You must register your product warranty online at www.wildgameinnovations.com. Follow the on screen directions to complete the process. WGI Innovations, LTD.
FCC FCC STATEMENT Product Name: Game Trail Camera Trade Name: Wildgame Innovations Model# W4FT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two criteria: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
602 Fountain Parkway Grand Prairie, TX 75050 800.847.8269 “Wildgame Innovations” and the “Button Logo” are TM trademarks of Wildgame Innovations, LLC. “Sport Responsible” , “Redux” and “Flextime” are TM trademarks of WGI Innovations, LTD.
