Infrared Digital Scouting Camera User’s Manual Model # M16i19-8
Includes Adjustable Strap page 1 User Manual Camera Unit
Features RESOLUTION MAX: 16 MP FLASH 36 High Intensity IR LED’s FLASH RANGE up to 80 feet SENSOR Passive Infrared Sensor (PIR) Motion and Heat SENSOR RANGE up to 60 feet IMAGE FORMAT JPEG - Digital Stills/ AVI-Digital Video MEMORY up to 32GB SD Card (not included and required) Class 4 and above recommended IMAGE RESOLUTION High (16 MP) Medium (10 MP) Low (5 MP) POWER SUPPLY 8 AA batteries (not included and required) Alkaline recommended BATTERY LIFE Estimated up to 1 year or 30,000 photos ONBOARD POWER Buil
Installing Batteries 1. Open the door at the bottom of the camera by unlatching the locking tab. 2. With the camera facing open, open the battery compartment cover by sliding the latch to the left. 3. With the bottom of the camera towards you, Make sure to insert the batteries into the camera with the positive ends towards you where marked positive and the negative ends towards you where marked negative. NOTE: Do not mix old and new batteries.
4. Close battery compartment cover. To latch the cover simply pull the latch slightly to the left as you close the battery compartment cover. 5. Load SD memory card (up to 32GB not included) into the SD card slot with the connectors facing up. IMPORTANT: Make sure the camera is powered off before removing or installing an SD card. If you are using an SD card from other cameras, please make sure to format the SD card in your computer prior to use in your camera.
Test Mode Power On 1. To turn the unit ON press and release the power button. Time/Date Location PIR Mode PIR Active PIR Sense Picture Resolution Delay 2. Still 24Hr High Regular High 5s 15s 30s Video Night Day Low Medium Wide Medium Low 1m 5m 10m Check the battery level icon to ensure the batteries just installed contain the proper charge level. If so, you are ok to proceed with camera use. NOTE: LCD cycle through camera information. PIR picture number > Remaining pictures > Time . page 5 1.
Power Save 1. After 30 seconds without any buttons being pushed, the LCD will turn off and camera enters into Power Save or Ready Mode. 2. The LCD screen can be awakened by pressing the Power button briefly. Setting Time 1. Note: The LCD will not “wake up” when camera is writing to memory.
Location Setting Date 1. Press the Enter navigation button after setting the minute to change the Date. 1. Press the Enter navigation button while Location is selected. The first character will be blinking. 2. Press the + or - navigation button to go up or down in sequence. Press the Enter navigation button when the character shown is what you want and move to the next character. 3. Repeat steps 1 and 2 to set the rest of the characters.
PIR Active PIR Mode 1. Press the Enter navigation button while PIR Mode is selected. The highlighted option will be blinking. POWER 2. + - + - Press the Enter navigation button while PIR Active is selected. The highlighted option will be blinking. ENTER Press the + or - navigation button to move to different options. Press the Enter navigation button to save the setting. POWER 1. POWER 2. + - ENTER Press the + or - navigation button to move to different options.
Exposure PIR Sensitivity 1. Press the Enter navigation button while PIR Sense is selected. The highlighted option will be blinking. 2. Press the + or - navigation button to move to different options. Press the Enter navigation button to save the setting. POWER PIR SENSE: POWER + + - - Press the Enter navigation button while Exposure is selected. The highlighted option will be blinking. 2. Press the + or - navigation button to move to different options.
Resolution 1. Press the Enter navigation button while Resolution is selected. The highlighted option will be blinking. POWER + - 2. Press the + or - navigation button to move to different options. Press the Enter navigation button to save the setting. ENTER POWER + - ENTER RESOLUTION: HI: Images will be at the highest resolution but take up the most space. MED: Images will be at medium resolution and take up average space. LO: Images will be at the lowest resolution and take up the least space.
1. Delay Power Off Press the Enter navigation button while Delay is selected. The highlighted option will be blinking. To turn the unit off, first wake up the LCD screen and then depress and hold the power button until the LCD turns off. Time/Date Location PIR Mode PIR Active PIR Sense Picture Resolution Delay POWER 2. + - ENTER Press the + or - navigation button to move to different options. Press the Enter navigation button to save the setting.
Image Stamp Pictures Display: A A- Time B- Date C- Moon Phase D- Location E- Photo Count B C D E Format SD Card SDXC cards are not supported. Having trouble with your SD card? Try this. 1. Connect the SD card to your computer. If your computer has an SD card slot you can insert the SD card directly into the port. NOTE: If you are using a MicroSD card, you will need an adapter to allow it to fit into standard SD card ports.
Mounting When mounting to a tree, first remove the clip from one end of the strap so you can slide the strap through the slots located on the back of the camera. Once the camera is attached place the clip back on to the strap. Then, wrap the strap around the tree and clip the two ends together. Pull the excess material so that the camera is straped tightly to the tree. page 13 TIPS: Recommended distance from target area is 25-30 feet for optimal imaging quality.
Retrieving Images (SD Card Reader) A. First, remove the SD Card from the camera unit itself by pressing on it to where it automatically ejects. B. Next, insert the SD card into your SD card reader. C. Once inserted into your computer it may automatically launch “AutoPlay”, a window recognizing a new Secure Digital Storage Device (the SD Card). D. If so, it should list several options for the next steps (not limited to the following): 1. Picture Options a. Import pictures b. View pictures c. Copy Disc d.
Warranty DISCLAIMERS WGI Innovations, LTD is not responsible for damage, expense or injury caused by the unauthorized use of, alterations to, improper connection of and abuse or neglect of the WGI Innovations™ products. WARRANTY For the warranty to be in effect, register your product at wildgameinnovations.com. Follow the onscreen directions to complete the process.
FCC FCC STATEMENT Product Name: Digital Game Scouting Camera Trade Name: Wildgame Innovations Model# M16i19-8 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two criteria: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
602 Fountain Parkway Grand Prairie, TX 75050 (800) 847-8269 wildgameinnovations.com “Wildgame Innovations” and the “Button Logo” are trademarks of Wildgame Innovations, LLC.
