3. Fitting the guard for straight shaft grass deflector -Fix the transmission with hex key and wrench enclosed as standard ‘accessories for tightening the news with the sags guard. -The guard Is flax to the angle transmission by two screws. Warning! Use only original manufacturers replacement parts, accessories and attachments. Failure to do so can cuss poor performance, possible injury and may void 'your warranty. Never use the machine without the guard assembled! 4.
c} Dreiser the Nylon cutting head. Use screw driver to hold flange and then rotate the Nylon ‘putting head clockwise, it will be replaced d} Fit the bide. Tass the cuter flans off afar assassins the nut, than put the bias, outer flans, shield and nut according to priority a8 below pictures. Nita the blade rotation direction seen be. samey as below picture. Use screw driver to hold flange and tighten nut counter-clockwise, ensure the nut s tightened enough.
6. Flt the bet According to cloture showing, fit the bet well OPERATION When operating this machine, please flow the instructions for operations steps. 1.
Before refueling: Shaka the fuel mixture container well. Place the machine on a flat stable surface, with the fue! tank cap facing upwards, Glean the fuse tank cap and the surrounding area to avoid any dirt from entering the tank during refilling. Carefully open the fuel tank cap to allow the pressure inside to decrease gradually. Use a funnel to refile and avoid filling the tank to the brim. = Unscrew the tank cap and remove it. Pouring the fus! carefully, avoid spilling.
Start on the unit Do not start the unit until it has been completely assembled. Before switching on the unit, always check the oil. Check before use Danger of Injurer Do ot operate the davit unless you did ot ind any f Suite, If part han Be coma adjectival, make sure fo replace 1 barroom you use the device again. Check the safe condition of the device: —Check the device for leaks. = Check the device for visual defects. — Check that all parts of the device have bean securely fitted.
3. Pull the recoil starter handle 3-5 times to start the engine. Hold the machine firmly on the ground with cne hand on the power unit, In order net to lose control of the machine during startup as following picture. 4. Pull the starter grip slowly for uni you feel some resistance, then tug it a few times until you hear the engine tum over. Then adjust the choke lever to (RUN) potion 5. Pull the starter grip again until the engine starts as normal.
6. When the engine is running and idling, the throttle lever on handier is as below picture. First pass the lock off lever and then switch the throttle lever on, the machine will be working. 7. Adjusting line length when working: This machine is fitted with a “Tap & Godhead T release more line, tap the cutting line head against the round with engine at top speed: the line will be released autocratically and the knife cut off the excess length. ol 8.
9. Ifany problem occurs, pull ths pin of safety bat, then release the brush cutter immediately 10. If the machine is hot, the throttle level can be adjusted fo ON position directly when restart machine. 11 WARNING! Do not use the machine for sweeping, siting the cutting Sine head. The power of engine could throw objects and small stones 15 mares or more, causing damage or injuries to people. i Ciceroni zone Note: 1. Do not start the motor In tall grass. 2.
Ll L e Correct maintenance is essential to maintain the original efficiency and safety of the machine over time. Before performing any maintenance or cleaning work, always turn off the engine. 1. Do not spray the unit with water. Ingress of water may damages the engine and electrical connection. 2. Clean the unit with a cloth, hand brush, etc. 'WARNING! During maintenance operations: — Remove the spark plug cap. —Walt until the engine Is sufficiently cold.
Change and clean the spark plug -Periodically remove and clean the spark plug using a metal brush to get rid of any deposits. -Check and reset the correct distance between the electrodes. -Replace the spark plug and fasten it firmly using the supplied wrench. ~The spark plug must be replaced with one with the same characteristics whenever the electrodes have bunt or the Insulation has worn, and In any case every 100 working hours.
