User Manual

3
Number of
Blinks
80ºF
85ºF
90ºF
95ºF
100ºF
105ºF
110ºF
120ºF
140ºF
185ºF
190ºF
192ºF
194ºF
196ºF
198ºF
200ºF
202ºF
204ºF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Temperature
Temperature Settings
Conrm/Reset Temperature (factory set at 190ºF . . . Cold Cappuccino set at 100ºF)
Enter program mode –PressandholdtheSTOP/WASHbuttonforaboutten[10]seconds,untilallthelightsonthe
controlpanelareblinking.
Set manual dispense –Whileyouareinprogrammingmode,pressandholdthePUSHbutton.
Hotliquidwillstarttoow.ContinuetoholddownthePUSHbuttonuntilliquidstopsowing,thenreleasethebutton.
Atthistime,youhaveselectedthemanualliquiddispensingmodeandhaveexitedoutofprogrammode.
Thesefeaturesallowyoutocheckorchangetheheatingtanktemperature,ifdesired.Thetemperatureinthetank
isprogrammablefrom80ºF,in5degreeincrementsupto140ºF,thenthetemperaturewilljump45degreesto185ºF
andresume2degreeincrementsuptoamaximum204°F(seeTemperatureSettingstable,right).
Enter program mode –PressandholdtheSTOP/WASH button foraboutten[10]
seconds,untilallthelightsonthecontrolpanelareblinking.
To set & exit - Press one of the PUSHbuttons.
To change the temperature - ReleasetheSTOP/WASHbutton,thenpressandholdit
again.Eachquickashrepresentsatemperatureincrease.SeetheTemperatureSettings
tablefortheactualtemperatures.ReleasetheSTOP/WASHbuttonwhenthedesired
temperatureisreached.
Enter temperature program mode –PressandholdtheSTOP/WASHbuttonfor
approximatelyonesecond,thenrelease.ThecurrentsettingwillbeindicatedbyLED
ashes.
To Change Tank Temperature
Programming Continued ...
WATER LEVEL ERROR –3LONGAND1SHORT
Whenthiscodeisseenonthecontrolpanel,thereisamalfunctioninthewaterlevelcontrolsystem.
COMMUNICATION ERROR –3LONGAND3SHORT
Thisashinglightpatternindicatesacommunicationerrorbetweentheswitchpanelonthedoorand
thepowermodule.
TEMPERATURE SENSOR ERROR –3LONGAND2SHORT
Whenthislightpatternisashingonthecontrolpanelthereisasystemfailurewiththeheatingtank.
ERROR CODES:CurtisCAFEPCsystemscontainvarioussafetyfeaturesintheelectroniccircuitrythatshutdownthefunctionsoftheunitintheeventofa
systemfailure.ErrorcodesaresignalledbytheREADYlightblinkingoneofthreepatterns:
FlushingtheWhipperChambers
Everythreetofourhours,ormoreoftenifnecessary,ushthewhipperchamber/dispensingsystem.
A. MakesurepowerisON.
B. PressandholdtheSTOP/WASHbutton.SelectoneofthePUSHdispensingbuttonsandpress.Hotrinsewaterwillushoutthesystem.
ReleasetheSTOP/WASHbuttonwhenthewaterrunsclear.
C. Cleanupanywaterthatmayhavespilled.
Cleaning
A. Switchofftheunitatthepowertoggleswitch,markedCONTROL,behindtheunit.
B. Wipeallexteriorsurfaceswithadampcloth;removinganyspills,dustordebrisfromtheunit.
C. Removethedriptrayandlouveredscreenandwashoutitscontents.Forhardtocleandeposits,useamilddetergentsolution.
D. Cleanaroundthedispensingarea,wipingwithanon-toxiccleaner.