User Manual

3
Number of
Blinks
80ºF
85ºF
90ºF
95ºF
100ºF
105ºF
110ºF
120ºF
140ºF
185ºF
190ºF
192ºF
194ºF
196ºF
198ºF
200ºF
202ºF
204ºF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Temperature
Temperature Settings
Conrm/Reset Temperature (Factory set at 190ºF . . . Cold Capppuccino set at 100ºF)
Enter Program Mode –pressandholdSTOP/WASHforaboutten[10]secondsuntilalllightsonthecontrolpanel
areblinking.
Set Manual Dispense –Whileyouareintheprogrammingmode,pressandholdthePUSHbutton.
Hotliquidwillstarttoow.
ContinuetoholddownthePUSHbuttonuntilliquidstopsowing,thenreleasethebutton.
Atthistime,youhaveselectedtheManualLiquidDispensingModeandhaveexitedoutoftheprogrammingmode.
Thesefeaturesallowyoutochecktheheatingtanktemperatureorchangethetemperatureifdesired.Thetem-
peratureinthetankisprogrammablefrom80ºF,in5degreeincrementsupto140ºF,thentemperaturewilljump45
degreesto185ºF,thenresume2degreeincrementsuptoamaximum204°F(seeTemperatureSettingstable,right).
Enter Program Mode – pressandholdSTOP/WASH foraboutten[10]secondsuntilall
lightsonthecontrolpanelareblinking.
Enter Temperature Program Mode –PressandholdSTOP/WASHforapproximately1
second,thenrelease.ThecurrentsettingwillbeindicatedbyLEDashes.
To Change Temperature.ReleaseSTOP/WASHbutton,thenpressandholdagain.Each
quickashrepresentsatemperatureincrease.SeetheTemperatureSettingstableforthe
actualtemperatures.ReleaseSTOP/WASHwhendesiredtemperatureisreached.
To Set and Exit,pressonofthePUSHbuttons.
To Change Tank Temperature
Programming Continued ...
WATER LEVEL ERROR –3LONGAND1SHORT
Whenthiscodeisseenonthecontrolpanel,thereisamalfunctioninthewaterlevelcontrolsystem.
TEMPERATURE SENSOR ERROR –3LONGAND2SHORT
Whenthislightpatternisashingonthecontrolpanelthereisasystemfailurewiththeheatingtank.
COMMUNICATION ERROR –3LONGAND3SHORT
Thisashinglightpatternindicatesacommunicationerrorbetweentheswitchpanelonthedoorand
thepowermodule.
ERROR CODES:CurtisCafesystemscontainvarioussafetyfeaturesintheelectroniccircuitrythatshutdownthefunctionsoftheunitintheeventofasystem
failure.ErrorcodesaresignalledbytheREADYlightblinkingoneofthreepatterns:
FlushingtheWhipperChambers
Everythreetofourhoursormoreoftenifnecessaryushthewhipperchamber/dispensingsystem.
A. MakesurepowerisON.
B. PressandholdtheSTOP/WASHbutton.SelectoneofthePUSHdispensingbuttonsandpress.Hotrinsewaterwillushoutthesystem.
LiftofftheSTOP/WASHbuttonwhenwaterrunsclear.
C. Cleanupanywaterthatmayhavespilled.
Cleaning
A. Switchofftheunitatthepowertoggleswitch,markedCONTROL,behindtheunit.
B. Wipeallexteriorsurfaceswithadampcloth;removinganyspills,dustordebrisfromtheunit.
C. Removethedriptrayandlouveredscreenandwashoutitscontents.Forhardtocleandeposits,useamilddetergentsolution.
D. Cleanaroundthedispensingarea,wipingwithanontoxiccleaner.