Programming instructions

FIND OUT MORE
ON
THE WEB.
WILBURCURTIS.COM
WILBUR CURTIS COMPANY
Montebello, CA 90640
1
F
IND OUT MORE
ON
THE WEB.
WILBURCURTIS.COM
Models Included
ALPHA-1DS
ALPHA-2DS
ALPHA-3DS
ALPHA-3DSR
ALPHA-3DSL
ALPHA-5DSR
ALPHA-5DSL
ALPHA-5DS
CAUTION: CAUTION:
CAUTION: CAUTION:
CAUTION: DO NOT
connect this brewer to
hot water. The inlet valve
is not rated for hot water.
CAUTION: CAUTION:
CAUTION: CAUTION:
CAUTION: Please use
this setup procedure
before attempting to use
this brewer. Failure to follow the
instructions can result in injury or
the voiding of the warranty.
WARNING TO AVOID
SCALDING, Do not
remove brewcone whil
brew light is flashing.
ISO 9001 REGISTERED
C
WARNING HOT LIQUID,
Scalding may occur.
Avoid splashing.
Important Safeguards/Conventions
Alpha DS Decanter Brewer Instructions
FOR THE LATEST SPECIFICATIONS AND INFORMATION GO TO
WWW.WILBURCURTIS.COM
This appliance is designed for commercial use. Any servicing other than cleaning and maintenance should be performed by an
authorized Wilbur Curtis service center.
Do NOT immerse the unit in water or any other liquid
To reduce the risk of fire or electric shock, do NOT open top or rear panel. No user serviceable parts inside. Repair should
be done only by authorized service personnel.
Keep hands and other items away from hot parts of unit during operation.
Never clean with scouring powders, bleach or harsh implements.
ConventionsConventions
ConventionsConventions
Conventions
WW
WW
W
ARNINGS – ARNINGS –
ARNINGS – ARNINGS –
ARNINGS –
TT
TT
T
o help ao help a
o help ao help a
o help a
void personal injurvoid personal injur
void personal injurvoid personal injur
void personal injur
yy
yy
y
Important Notes/Cautions – from the factorImportant Notes/Cautions – from the factor
Important Notes/Cautions – from the factorImportant Notes/Cautions – from the factor
Important Notes/Cautions – from the factor
yy
yy
y
SanitaSanita
SanitaSanita
Sanita
tion Requirementstion Requirements
tion Requirementstion Requirements
tion Requirements
YY
YY
Y
our Curtis our Curtis
our Curtis our Curtis
our Curtis
ADS System is FADS System is F
ADS System is FADS System is F
ADS System is F
actoractor
actoractor
actor
y Pre-Set and Ready Pre-Set and Read
y Pre-Set and Ready Pre-Set and Read
y Pre-Set and Read
y to Go… Right from the Carton.y to Go… Right from the Carton.
y to Go… Right from the Carton.y to Go… Right from the Carton.
y to Go… Right from the Carton.
Following are the Factory Settings for your ALPHA™ DS Coffee Brewing Systems:
• Brew • Brew
• Brew • Brew
• Brew
TT
TT
T
emperaempera
emperaempera
empera
ture = 200°Fture = 200°F
ture = 200°Fture = 200°F
ture = 200°F
• Brew • Brew
• Brew • Brew
• Brew
VV
VV
V
olume = Set to dispensing vessel requirements (60 oz)olume = Set to dispensing vessel requirements (60 oz)
olume = Set to dispensing vessel requirements (60 oz)olume = Set to dispensing vessel requirements (60 oz)
olume = Set to dispensing vessel requirements (60 oz)
WW
WW
W
armer Setting on HIGH with Quality armer Setting on HIGH with Quality
armer Setting on HIGH with Quality armer Setting on HIGH with Quality
armer Setting on HIGH with Quality
TT
TT
T
imer OFFimer OFF
imer OFFimer OFF
imer OFF
Generally there will never be a reason to change your ADS programming. However, should you need to make slight adjustments to
meet your brewing needs, programming instructions are provided later in this manual.
System Requirements:
WW
WW
W
aa
aa
a
ter Sourceter Source
ter Sourceter Source
ter Source 20 – 90 PSI (Minimum Flow Rate of 1 GPM)
• Electrical:• Electrical:
• Electrical:• Electrical:
• Electrical: See attached schematic for standard model or visit www.wilburcurtis.com for your model.
Equipment to be installed to comply with applicable federal, state, or local plumbing/electrical codes having jurisdiction.
SETUP STEPSSETUP STEPS
SETUP STEPSSETUP STEPS
SETUP STEPS
The unit should be level (left to right and front to back), located on a solid counter top. Connect a water line from the water filter to the
brewer. NOTE: Some type of water filtration device must be used to maintain a trouble-free operation. (In areas with extremely hard
water, we suggest that a sedimentary and taste & odor filter be installed.) This will prolong the life of your brewing system and
enhance coffee quality.
1. A 3/8” NPT x 1/4” Flare elbow has been supplied for water line connection. Use tubing sized sufficiently to provide a minimum of
1.0 GPM.
2. Connect the unit to an appropriate electrical power circuit.
3. Turn on the toggle (STANDBY/ON) switch behind the unit. The heating tank will start to fill. When the water level in the tank rises
to the correct volume, the heating elements will energize automatically. With ADS Systems there is no danger of element burnout
caused by an empty tank.
4. The heating tank will require 20 to 30 minutes to reach operating temperature (200°F) as indicated by the READY-TO-BREW
indicator.
5. Prior to brewing, dispense 12 ounces of hot water through the hot water faucet.
6. Brew a cycle of at least 12 ounces, to purge the water lines of any air that may be trapped after filling.
The National Sanitation Foundation requires the following water connection:
1. A quick disconnect or additional coiled tubing (at least 2x the depth of the unit) so that the machine can be moved for
cleaning underneath.
2. In some areas an approved backflow prevention device may be required between the brewer and the water supply.
BREWING INSTRBREWING INSTR
BREWING INSTRBREWING INSTR
BREWING INSTR
UCTIONSUCTIONS
UCTIONSUCTIONS
UCTIONS
1. Brewer should be ON (Confirm at rear toggle switch, then press ON/OFF button). Ready-to-Brew light should be ON.
2. Place empty DB-12 Decanter (not included) on warmer.
3. Place filter in Brewcone.
4. Pour ground
coffee into
brewcone.
5. Position
brewcone into
brew rails.
6. Press Brew
button.
WW
WW
W
ILBURILBUR
ILBURILBUR
ILBUR
C C
C C
C
URTISURTIS
URTISURTIS
URTIS
C C
C C
C
OMPOMP
OMPOMP
OMP
ANYANY
ANYANY
ANY
, I, I
, I, I
, I
NCNC
NCNC
NC
..
..
.

Summary of content (4 pages)