Owner manual

ENVIRONMENTAL CONTROLS
INTEGRITY “32” SERIES AIR-COOLED
SIDE-MOUNTED AIR CONDITIONERS
K19
Standard Features
• CFC-Free Refrigerant
• EMI/RFI Suppressor
• Internal corrosion protection
• Low Temperature Control Thermostat
• M/TAB Mounting System
• NEMA 4/4X Rating Maintained
(UL50)
• Stainless Steel Cabinet
• UL/CUL Recognized
‡
Accessories and Options
• Cooling Effect Detector
• Filter Recoating Adhesive
• Filters for replacement
• Lifting Eyes
• Low Ambient Kit & Compressor
Heater
• Short Cycle Protector
• Special materials or finishes
www.hubbell-wiegmann.com
Data Subject To Change Without Notice
NEMA
TYPE 4/4X
MAINTAINED
32.25
[819.2]
13.12
[333.2]
31.50
[800.1]
M/TA B
THERMOSTAT
ADJUSTMENT
ACCESS
14.50
[368.3]
13.00
[330.2]
1
2
3
4
3
80
70
90 100 110 120 130
3000
4000
5000
6000
7000
8000
2000
1000
0
Ambient Temperature (ºF)
Cooling Capacity (BTU/H)
Maximum enclosure
air temperature ºF
75
80
90
10 0
110
120
125
KNA4C4P32R
Operation within shaded areas not
recommended.
PERFORMANCE CHART
WNA4C4P32R
MODEL
RATED CAPACITY 95/95 RATING AMBIENT TEMP. °F VOLTS HZ RUNNING APPROX.
(BTU/H) (BTU/H) MAX./MIN. AMPS WEIGHT (LBS.)
WNA4C4P32L 4000 2650 125/50 115/100 60/50 13.0/12.0 105
W2NA4C4P32L 4000 2650 120/50 230/200 60/50 6.0 105
INTEGRITY SERIES 32 AIR-COOLED PANEL-MOUNTED AIR CONDITIONERS
MOUNTING PLAN
UNIT MUST BE 12" (300mm)
MINIMUM ABOVE FLOOR
FOR FILTER ACCESS
14.50
[368.3]
0.38
[9.7]
32.25
[819.2]
4.00
[101.6]
TYP.
1. 0 0
[25.4]
4.00
[101.6]
13.13
[333.2]
1. 3 8
[35.1]
14.50
[368.3]
13.75
[349.3]
M/TA B
POWER
CORD
0.81
[20.6]
0.88
[22.4]
30.19
[766.8]
5.00
[127.0]
12.88
[327.2]
26.00
[660.4]
M/TA B
OUTLINE
UNIT
OUTLINE
(24) .250 [6.3]
DIA. HOLES
1.25
[31.7]
4.00
[1 0 1.6]
1. 2 5
[31.7]
31.50
[800.1]
0.37
[9.4]
13.75
[349.2]
1.37
[34.8]
4.25
[1 07.9]
TYP.
0.37
[9.4]
2.00
[50.8]
10.50
[266.7]
TYP.
13.00
[330.2]
TYP.
4.62
[117.3]
5.12
[130.0]
11.5 0
[292.1]
TYP.
1. 5 0
[38.1]
3.50
[88.9]
3.81
[96.8]
8.00
[20.3]
8.00
[20.3]
2.18
[55.4]
3.12
[79.2]
2.18
[55.4]
4.25
[108.0]
TYP.
(6) .312 [8.0]
DIA. HOLES
(24) .203 [5.0]
DIA. HOLES
3
4
3
3
3
4
3
4
13.06
[331.7]
1
2
UNIT M/TAB & CUTOUTS
Dimensions, inches [metric], are for reference only and subject to change.
‡
UL/CUL Recognized models are available as Listed at added cost.