User guide

F60
www.hubbell-wiegmann.com
Data Subject To Change Without Notice
TYPE AMP FUSE FUSE DISCONNECT DISCONNECT TWO DOOR
FREESTANDING MODULAR
NUMBER RATING CLIP CLASS HEIGHT X WIDTH Y FLOOR-MOUNT
TCN-30C 30A No fuse — 5.90 6.20
TCF-30C 30A 30A-250V H, K, R 7.50 6.20
TCF-33C 30A 30A-600V H, K, R 10.15 6.20
TCF-33C 30A 60A-250V H, K, R 8.15 6.20
TCF-33C 30A 30A-600V J 7.50 6.20
TDN-60C 60A No fuse — 5.90 6.20 For enclosures
TDF-60C 60A 30A-600V H, K, R 10.15 6.20 that accept
TDF-60C 60A 60A-250V H, K, R 8.15 6.20 these devices,
TDF-63C 60A 60A-600V H, K, R 10.65 6.20 see pages F28-F29
TDF-63C 60A 60A-600V J 7.50 6.20 & F45-F46
TEN-10C 100A No fuse — 5.90 6.20
TEF-10C 100A 100A-250V H, K, R 10.35 6.20
TEF-10C 100A 100A-600V H, K, R 10.35 6.20
TEF-10C 100A 100A-600V J 10.35 6.20
SCHNEIDER SQUARE D
®
CLASS 9422 DISCONNECT SWITCHES USED WITH CABLE MECHANISM 9422-CFT30 AND 9422-A1 HANDLE MECHANISM
CABLE TYPE CIRCUIT B CIRCUIT B CIRCUIT BREAKER CIRCUIT BREAKER TWO DOOR
FREESTANDING MODULAR
SWITCH AMP RATING FRAME TYPE HEIGHT X WIDTH Y FLOOR-MOUNT
9422 CGJ30 75A GJL 4.75 3.50
9422 CGJ30 100A GJL 4.75 3.50
9422 CFA30 100A FAJ, FHL 6.00 4.50
9422 CKA30 250A KAL, KHL 8.00 4.50
9422 CLA30 400A LAL, LHL, Q4L 11.00 6.00
SCHNEIDER SQUARE D
®
CLASS 9422 CABLE MECHANISM FOR CIRCUIT BREAKERS
Use switches listed above with appropriate cable mechanism and 9422-A1 handle mechanism. Cable operators are available in 3-foot, 5-foot, and 10-foot lengths.
Numbers shown (30) are for 3-foot cables.
Use cable mechanism with appropriate circuit breaker and 9422-A1 handle mechanism. Cable operators are available in 3-foot, 5-foot, and 10-foot lengths.
Numbers shown (30) are for 3-foot cables.
Space Occupied by Disconnect Switch or Circuit Breaker
• Schneider Square D
®
cable mechanisms allows disconnect devices to be positioned independent from the flange-mounted handle mechanism.
•RefertoNational Electrical Code
®
article 430-10(b) for wiring space “WB” required for line side conductors.
• Choose cable mechanism length based on placement of disconnect in enclosure. See Schneider Square D
®
instruction Bulletin for minimum bend radius
for cable.
• Space occupied by disconnect is determined by overall height “X”, width “Y”, wire bend space “WB” and location “G” as selected from right to left.
For enclosures that
accept these devices,
see page F28-F29 &
F45-F46
For enclosures that accept
these devices,
see pages F32-F49
†For Two Door Floor-Mount NEMA 12 “E” = 7.88 when “H” = 60.12
(Pages F28-F29 & F45-F46) “E” = 13.38 when “H” = 72.12
For Heavy Duty Freestanding “E” = 11.88 when “H” = 72.12
and Modular Enclosures “E” = 17.38 when “H” = 84.12
(Pages F32 - F49) “E” = 20.38 when “H” = 90.12
FLOOR-MOUNT • FREESTANDING • MODULAR SERIES ENCLOSURES
DISCONNECT SPACE OCCUPIED & AVAILABLE WIRING SPACE INFORMATION
For enclosures
that accept these devices,
see pages F32-F49