User`s manual

ManualsBrandsWide ManualsComputer equipmentIDP2310UX

Issued Date

Revision Status

Title

Page No.

1 / 44

V2.2

2009-2-20

IDP2310UX

(AL23PUX)

USER’S MANUAL

IDP2310UX

1600 x 1200 TFT LCD MONITOR

23.1" COLOR DISPLAY

Proprietary Data Notice:

This document as well as all reports, drawings, data, information, or other material, whether accompanying it are the property of

WIDE Corporation, are disclosed by WIDE only in confidence, and, except as WIDE may otherwise permit in writing, are to be

used, disclosed, or copied only to the extent necessary for the evaluation thereof by recipient, or higher-tier contractor or

subcontractor.

Information in this document is subject to change without prior notice.

Summary of content (44 pages)

PAGE 1
Page No. Title IDP2310UX 1 / 44 (AL23PUX) USER’S MANUAL IDP2310UX 1600 x 1200 TFT LCD MONITOR 23.
PAGE 2
Page No. Title IDP2310UX 2 / 44 (AL23PUX) Table of Contents SAFETY INSTRUCTIONS .................................................................................................................4 FCC INFORMATION ..........................................................................................................................5 VCCI ...................................................................................................................................................
PAGE 3
Page No. Title IDP2310UX 3 / 44 (AL23PUX) 3.3.1 3.3.2 3.3.3 3.3.4 Revision Status V2.2 Adjustment .................................................................................................................28 COLOR ADJ ................................................................................................................31 PIP(Picture In Picture) ...............................................................................................34 SETUP MENU ................................
PAGE 4
Page No. Title IDP2310UX 4 / 44 (AL23PUX) SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION: DOUBLE POLE / NEUTRAL FUSING. DISCONNECT POWER BEFORE CHANGING FUSE. Precautions ON SAFETY 1.
PAGE 5
Page No. Title IDP2310UX 5 / 44 (AL23PUX) Do not clean the front panel with keton-type materials(e.g., acetone), ethyl alcohol, toluene, ethyl acid, methyl or chloride – these may damage the panel. ON REPACKING Do not throw away the carton and packing materials. They make an ideal container which to transfer the unit. If you have any questions about this unit, contact your authorized dealer. ON DISPOSAL This unit contains which can pollute the environment if disposed carelessly.
PAGE 6
Page No. Title IDP2310UX 6 / 44 (AL23PUX) Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. If necessary, consult your dealer or an experienced radio/television technician for additional suggestions. You may find the booklet called How to identify and Resolve Radio/TV Interference Problems helpful. This booklet was prepared by the Federal Communications Commission. It is available from the U.S.
PAGE 7
Page No. Title IDP2310UX 7 / 44 (AL23PUX) BRIEF DESCRIPTION GENERAL This specification defines the requirements for the IDP2310UX, 23.1” COLOR DISPLAY TFT LCD monitor with 1600 X 1200 pixels visible resolution, which is designed and tailored for use in operator display systems such as ECDIS monitor applications. The IDP2310UX has a 23.1” diagonal viewable display area and 1600 x 1200 pixels addressable resolution. The (0.098 X RGB) X 0.
PAGE 8
Page No. Title IDP2310UX 8 / 44 (AL23PUX) 1. TECHNICAL SPECIFICATIONS 1.1 ELECTRO-OPTICAL SPECIFICATIONS 1.1.1 1.1.1.1   1.1.1.2   1.1.1.3  1.1.1.4    1.1.1.5  Screen Specifications Panel Technologies AMLCD (Active Matrix Liquid Crystal Display) technology Amorphous silicon TFT (Thin Film Transistor) technology Screen Dimensions Aspect ratio 4:3 Active screen size:  470.4 (H) x352.8 (V) mm (18.52” x 13.89”)  588.0 mm (23.
PAGE 9
Page No. Title IDP2310UX 9 / 44 (AL23PUX) 1.1.3    Input Signal Specifications IDP2310UX provides maximum five (5) input signal interfaces, 2 x Analog (BNC,D-sub) Input ,1x Digital Input, 1xCVBS input and 1xS-video. Standard input resolution is UXGA (1600 x 1200 pixels) Other resolutions are supported as specified below. No scaling is provided for input signals with resolutions less than the standard input resolution 1600x 1200 pixels. Hsync Vsync Resolution (KHz) (Hz) 31.0 - 43.0 60.0 - 85.
PAGE 10
Page No. Title IDP2310UX 10 / 44 (AL23PUX)  Manual: Operator can select the input manually using control panel. 1.1.4 1.1.4.1  1.1.4.2    Controls of the Display Remote Control via serial ports (JH Communication compatible) There are serial ports on the back side of the IDP2310UX for remote control of the monitor by customer application.
PAGE 11
Page No. Title IDP2310UX 11 / 44 (AL23PUX) Standard: IEC type connector  1.1.7.2 Input signal connectors Analog Input: 5 Coaxial BNC connectors for R, G, B, HS and VS Digital input: DVI-D connectors CVBS input: RCA connectors S-video input: 4pin mini DIN connectors     1.1.7.3 Interface connectors for remote control RS-422 port: RS-232 or RS-485 port: RS-485 port:    1.1.
PAGE 12
Page No. Title IDP2310UX 12 / 44 (AL23PUX) Digital Input ● Connection Type : 29p DVI-I Female (Digital only support) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24.
PAGE 13
Page No. Title IDP2310UX 13 / 44 (AL23PUX) Serial Interface ● Remote In(female) 1. 2. 3. 4. 5. 6. 7. 8. 9. No connection RxD (for RS-232) TxD (for RS-232) TxIN_B (for RS-485) RxIN_B (for RS-485) No connection Ground TxIN_A (for RS-485) RxIN_A (for RS-485) ● Remote out(male) 1. No connection 2. No connection 3. No connection 4. TxOUT_B (for RS-485) 5. RxOUT_B (for RS-485) 6. No connection 7. Ground 8. TxOUT_A (for RS-485) 9. RxOUT_A (for RS-485) Revision Status V2.
PAGE 14
Page No. Title IDP2310UX 14 / 44 (AL23PUX) 1.2 MECHANICAL SPECIFICATIONS 1.2.1 Dimension and Weight (Rack Mount ) The dimension of the unit is as shown in the table below: Monitor only Packing Height (mm / inch) 534 / 21.02 780/ 30.71 Width (mm / inch) 584 / 22.99 790/ 31.10 Depth (mm / inch) 93.8 / 3.69 297.5/ 11.72 Weight (kg / lbs) 15.5 / 34.2 20.5 / 45.2 The following figures show a Rack Mount version mechanical dimension.
PAGE 15
Page No. Title IDP2310UX 15 / 44 (AL23PUX) < IDP2310UX Bottom View > < IDP2310UX Rear View > Revision Status V2.
PAGE 16
Page No. Title IDP2310UX 16 / 44 (AL23PUX) < IDP2310UX Side View : unit mm> Revision Status V2.
PAGE 17
Page No. Title IDP2310UX 17 / 44 (AL23PUX) 1.2.2 Mounting The weight for the unit shall not exceed 15.5 kg (34.2 lbs)  Fixing: using 4 captive M6 bolts in front bezel  IDP2310UX can be Standard rack mounted with an optional adapter plate 1.2.3 Finishing   Standard Bezel color is Black (Rack Mount Type) Other bezel colors can be made available on request 1.2.4 Screws/Bolts   Number of screws to use for maintenance: reduced to minimum Type of screws requires maximum 3 standard tools 1.2.
PAGE 18
Page No. Title IDP2310UX 18 / 44 (AL23PUX) 1.3.4 Altitude   Non-operating Operating : Up to 30,000 ft : Up to 10,000 ft 1.3.5 EMC      FCC Part 15 subpart B, Class A CE(EMC) -EN55022(EMI) -EN55024(EMS) MIC VCCI Class A IEC60945 1.3.6 Safety  CE & CB EN60950-1  UL / cUL UL60950-1 1.3.7 Certificate for ECDIS  EN61174(IEC61174) 1.3.8 Drip-proof  Front side is drip-proof. Test shall be done when the unit is mounted in a console.
PAGE 19
Page No. Title IDP2310UX 19 / 44 (AL23PUX)  Use of maintenance equipment A modular design is taken for the unit. No special tools or equipment are required for maintenance purpose. 1.4.3 Use of toxic materials Cold Cathode Fluorescent Lamp (CCFL) in the backlight assemblies contains a small amount of mercury. The backlight assembly is placed inside of the monitor and is not exposed to user. 1.4.
PAGE 20
Page No. Title IDP2310UX 20 / 44 (AL23PUX) 2. Communication 2.1 Protocol 2.1.1 ASCII Characters Table : All communications are based on ASCII Code. ASCII ASCII ASCII Char. Char. Code Code Code Char. ASCII Code Char.
PAGE 21
Page No. Title IDP2310UX 21 / 44 (AL23PUX) 2.2.2 Byte# Communication Data Format 0 1 2,3,4 5 6 7,ect 7+LEN ATTN ADDR CMD LEN IHCHK DATA IDCHK Attention (ATTN) This byte is used to identify a start of message. It can be one of 3 values: ATTN Description 0x07 Command (ASCII BELL) 0x06 Acknowledge (ASCII ACK) 0x15 Negative Acknowledge (ASCII NAK) A device shall send a command using the 0x07 Attention Code.
PAGE 22
Page No. Title IDP2310UX 22 / 44 (AL23PUX) Command (CMD) The command shall be one of the following values: CMD 0 CMD1 CMD2 ASCII Description 0x42 0x52 0x54 “BRT” Brightness Command 0x4D 0x41 0x4E “MAN” Manufacturer ID Code 0x4D 0x43 0x43 “MCC” Display Control Command 0x54 0x59 0x50 “TYP” Type/Model Number Command Brightness Command “BRT” This command shall be sent to the display to command the backlight brightness control setting.
PAGE 23
Page No. Title IDP2310UX 23 / 44 (AL23PUX) Contrast control- 0x82, ”a” l “A”, Set all contrast = all channels nn l “+” l “-“ l Value / increment / decrement “r” l “R” Reset “?” Query Color temperature 0xb3, Select color temperature = Main selected select nl Value “0”－9200K. “r” l “R” l Reset “1”－6400K. “?” Query “2”－5600K.
PAGE 24
Page No. Title IDP2310UX 24 / 44 (AL23PUX) V position 0x87, Set H position nnn l “+” l “-“ l Value / increment / decrement “r” l “R” l Reset “?” Query PIP window size 0xa6, Select PIP window size = PIP window size selected Select nl PIP window size value “0”－small size “r” l “R” l Reset “1”－large size “?” Query 0xa7, Select input main = Main selected.
PAGE 25
Page No.
PAGE 26
Page No.
PAGE 27
Page No. Title IDP2310UX 27 / 44 (AL23PUX) The LED light intensity is adjusted with the backlight Knob. HOT KEY The user can assign various display function as hot keys Hot Key1 is able to directly source change. Press the “SELECT”. Hot Key2 is able to directly PIP. Press and hold the “◀” for 5seconds Hot Key3 is able to directly auto adjustment in Analog. Press the “▶” for 5 seconds. When auto adjustment is preformed on the special pattern, if it needs, firstly contact for us.
PAGE 28
Page No. Title IDP2310UX 28 / 44 (AL23PUX) 3.3.1 Adjustment The “Adjustment” menu is for controlling the brightness, contrast, positions, sharpness, clock and phase. 3.3.1.1 BRIGHTNESS The function is able the user to adjust brightness for the display, 50 is default value. “Brightness” adjusts the light output by controlling the opening of Liquid Crystal, it is different from “Dim Brightness” which is adjusted by controlling the amount of light of backlight directly.
PAGE 29
Page No. Title IDP2310UX 29 / 44 (AL23PUX) 3.3.1.2 CONTRAST The function is able the user to adjust contrast for the display, 50 is default value. “Contrast” is the submenu of “Adjustment”, which sets up the gain of output video signal to panel. Its adjustment range is 0 to +100. When one of the submenus of “Adjustment” selected, the select button push to select it. so that adjust the values of the Contrast. When the menu button pushed, going to the upper menu.
PAGE 30
Page No. Title IDP2310UX 30 / 44 (AL23PUX) 3.3.1.4 V.POSITION The function is able the user to adjust vertical position of the display. “V-Position” is the submenu of “Adjustment”, which controls the vertical position of image, Its adjustment range is 0 to +100 and default is 50. When the V-position of the submenu of “Analog adjustment” is selected, the select button push to select it. so that adjust the values of the V-position. When the encoder switch pushed , going to the upper menu.
PAGE 31
Page No. Title IDP2310UX 31 / 44 (AL23PUX) 3.3.1.6 CLOCK The function is able the user to adjust the number of sampling clock. The “Clock” is the menu for the setting of the number of pixels corresponding to the pixel rate of the applied analog input signal. It represents the number of sampling clock during one period of horizontal sync signal. 3.3.1.7 PHASE The function is able the user to adjust phase of sampling clock Its range is 0˚ to 360˚ , which is adjusted by 5.
PAGE 32
Page No. Title IDP2310UX 32 / 44 (AL23PUX) 3.3.2.1 COLOR TEMPERATURE The function is able the user to modify the color temperature of the picture for the Display. Higher temperature : “cooler” picture. Lower temperature : “warmer” picture. User can select one of 9200K, 6400K, 5600K and User color temperature measured You can adjust color temperature via the User(RGB) 3.3.2.
PAGE 33
Page No. Title IDP2310UX 33 / 44 (AL23PUX) When all white levels are on the points of OSD 50, the amount of color is the same each other. But, if the level is moved closed to OSD 100, the amount of color to adjust is more, so, the color to adjust looks like strong. On the other way, if it goes to OSD 0, the amount of color to adjust is less, so, the color is felt weakly. If the color is changed in brighter level, adjust the white level. But it also effects on dark level. 3.3.2.
PAGE 34
Page No. Title IDP2310UX 34 / 44 (AL23PUX) 3.3.3 PIP(Picture In Picture) This function is for displaying the video image window on the image from PC. CVBS or S-Video is possible to display on PIP window. The image from PC over DVI, BNC and D sub connector is unable to display on the window. 3.3.3.1 PIP ON/OFF This function is able the user to configure PIP window ON/OFF < PIP ON > Revision Status V2.
PAGE 35
Page No. Title IDP2310UX 35 / 44 (AL23PUX) 3.3.3.2 PIP SIZE This function is able the user to configure PIP window size. Revision Status V2.
PAGE 36
Page No. Title IDP2310UX 36 / 44 (AL23PUX) 3.3.3.3 PIP LOCATE The function is able the user to the configure PIP horizontal and vertical position Revision Status V2.
PAGE 37
Page No. Title IDP2310UX 37 / 44 (AL23PUX) 3.3.3.4 PIP SOURCE The function is able the user to configure PIP input source. CVBS = manual select composite video signal only SVIDEO = manual select S-Video signal only. 3.3.4 SETUP MENU In this menu, user can set up the setting values. Revision Status V2.
PAGE 38
Page No. Title IDP2310UX 38 / 44 (AL23PUX) 3.3.4.1 INPUT SELECT The function is able the user to select one of Analog RGB(D-sub), Digital RGB, BNC,CVBS and S-Video 3.3.4.2 COMMUNICATION “Communication” represents the communication setting between monitors or between the control system and the monitor Revision Status V2.
PAGE 39
Page No. Title IDP2310UX 39 / 44 (AL23PUX) 3.3.4.2.1 ID This assigns the monitor’s number, range Zero to fifteen, in order to identify the monitors, and it must be unique for distinguishing from each other. And, In the case of chaining several monitors thru communication port, the ID of monitor to be connected with control system must by Zero. 3.3.4.2.
PAGE 40
Page No. Title IDP2310UX 40 / 44 (AL23PUX) 3.3.4.2.3 Communication This assigns the communication mode. The monitor connecting with the control system is assigned the RS232 or RS422 and it connecting with other monitor is assigned to the RS485. So, one of three must be chosen as input communication mode. 3.3.4.3 OSD SETUP “OSD Set Up” is the submenu of “Set-Up” which sets up the position of OSD, and OSD Timeout. Revision Status V2.
PAGE 41
Page No. Title IDP2310UX 41 / 44 (AL23PUX) 3.3.4.3.1 H.Position This function is able to adjust the horizontal position of OSD. 3.3.4.3.2 V.Position This function is able to adjust the vertical position of OSD. 3.3.4.3.3 TIME OUT “OSD Timeout” is the submenu of “OSD Set Up”, which controls the time to display the OSD menu 20, 30, 50, and 100 : When the user don’t touch anything, the OSD menu is disappeared after 20, 30, 50 or 100 seconds, which keeps display OSD. 3.3.4.3.
PAGE 42
Page No. Title IDP2310UX 42 / 44 (AL23PUX) 3.3.4.4 Buzzer Set Up. This function is available to the buzzer model only This function is buzzer on/off and adjusts volume controls. 3.3.4.4.1 On/Off Buzzer On/Off control 3.3.4.4.2 Volume The sound adjust the ‘low, middle and high’ Revision Status V2.
PAGE 43
Page No. Title IDP2310UX 43 / 44 (AL23PUX) 3.3.4.5 FACTORY RECALL “Factory Recall” is the menu for restoring to the factory setting values. The settings with which the display leaves factory are stored in a factory settings storage area on main control board. And the current settings are stored in a user settings storage area on main control board. At administrator level, the current settings are replaced by the factory settings. The user settings disappear after changing by the factory settings. 3.3.
PAGE 44
Page No. Title IDP2310UX 44 / 44 (AL23PUX) 3.3.4.6.1 Serial NO. “Serial No.” describes the serial number of monitor. The serial number is unique on every monitor. 3.3.4.6.2 SW ver. “S/W ver.” describes the version of software installed on monitor. 3.3.4.6.3 Temp. “Temp. Status” describes the current internal temperature status or the information of the warning level (65℃), the critical Value (80℃) and the safe level (64℃). See 1.1.6.4. 3.3.4.6.4 Input A signal to display now on screen is described. 3.