Specifications

ManualsBrandsWIA-FA ManualsElectronicsWIA-FA Wireless Equipment

Table Of Contents

WIA-FA Wireless Communication Device Specification

WIA-FA Wireless Communication Device Specification

1. Introduction

WIA-FA wireless communication devices, developed by Shenyang Institute of Automation, Chinese

Academy of Sciences according to the WIA-FA standard, are a group of products for wireless data transmission

in factory automation. WIA-FA wireless communication devices are specially designed to meet the requirements

of factory automation in terms of high real-time and high reliability. The typical networking structure

of WIA-FA

includes gateway devices, access devices (ADs), and field devices (FDs). The hardware platforms of the three

types of devices are the same, but their software systems are different according to the functional requirements.

The main technical indexes are given as follows:

 Input voltage 9~24V and power 5W;

 Operating environment:

temperature 0∼70℃ and moisture 0

∼

85%RH;

 Network scale of one thousand nodes;

 The data period of nodes less than 10ms, for networks with 100 nodes;

 Communication reliability above 99.99%;

 Interconnection with TCP/UDP protocol.

2. Device Size

3. I

nterface Description

WIA-FA wireless communication devices provide one adaptive Ethernet port with 10/100/1000Mbps, one

power interface, one RS-232 serial

interface, three antenna interfaces, one USB 3.0 debugging interface, one

USB 2.0 debugging interface, and one HDMI debugging interface. The specifications and detailed descriptions

Model No.:WIA-FA-FD-X-RJ45

Summary of content (7 pages)

PAGE 1
WIA-FA Wireless Communication Device Specification 1. Introduction Model No.:WIA-FA-FD-X-RJ45 WIA-FA wireless communication devices, developed by Shenyang Institute of Automation, Chinese Academy of Sciences according to the WIA-FA standard, are a group of products for wireless data transmission in factory automation. WIA-FA wireless communication devices are specially designed to meet the requirements of factory automation in terms of high real-time and high reliability.
PAGE 2
of the interfaces are given in the following table. No. 1 Interface Antenna interface 1 External object Description Antenna or Internal pin and external threaded interface, with antenna internal hole and internal threaded antenna or antenna extension cable extension cable 2 Power interface DC 9-24V The inner core is DC+ and the outer ring is DC- 3 HDMI interface Monitor Used only as a debugging interface, not open to users 4 USB 3.
PAGE 3
9 Serial interface User device RS-232 interface based on DB9 10 Switch button N/A Switch button with an indicator light in the outer ring 4. Installation Requirement The WIA-FA wireless communication devices need to be placed horizontally. The size of the devices without antennas is 153mm×109.7mm×47mm. In order to guarantee that a WIA-FA wireless communication device can be properly installed, an area with the size of 153mm×180mm is at least required.
PAGE 4
5. Accessories The accessories of WIA-FA wireless communication devices are given as follows: No. Accessory Quantity 1 Antenna 3 Required 2 Power line 1 Required 3 Ethernet cable 1 Optional, customer self-supplied cable can be used 4 Antenna extension wire 3 Optional，only needed when moving antennas outward Note Figure The installing method of antennas: Take an antenna out of the packaging bag, align it with the position of an antenna joint, and rotate the antenna clockwise until tight.
PAGE 5
The connecting method of antenna extension cables: Take an antenna extension cable out of the packaging bag, align it with the position of an antenna joint, and rotate the nut clockwise until tight. The schematic diagram of connecting an antenna extension cable is given as follows: Note: Either antennas or antenna extension cables can be installed on a WIA-FA wireless communication device.
PAGE 6
The installing method of the Ethernet cable: Take the Ethernet cable out of the packaging bag, align it with the position of the network port, and insert the Ethernet cable into the network port. After installation, the Ethernet cable cannot be pulled out directly. The schematic diagram of installing the Ethernet cable is given as follows: 6.
PAGE 7
FCC ID: 2ATP6SIA-WIA-FA-X01 Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.